Community Brag Posts

Found the headboard directions on here... Messed w dementions for footboard n connect it w a 2x12 w three lag bolts each comer. Night stand was constructed the same but on a smaller scale

This was my husband's and my second furniture build, and the first with doors! We went ahead and followed the dimensions in the instructions, and even with wood that was 3.5, we still had doors that were a little short. I figure it adds character. Hinges were a little difficult for us, as we are new to woodworking DIY projects, but I'm very happy with the final project. Edge banding, magnetic clasps, and stain throughout really makes it look like a nice, finished piece. Thanks, Ana!

A side note on timing, for us this was a long weekend project that took us in to the next week. For others, I am sure it could go much quicker. That time also included finishing.

Built this 8' farm table after watching your video. Its my first piece of furniture. 

Thanks to Ana's plans I was able to build this in a couple of hours. It's not necessary, but a miter saw makes this project a cinch. I used one coat of Minwax Mahogany for the stain and distressed the wood with various sharp edged tools from my garage. I used a large Lowes moving box ($1.50) to cut the backing to 18"x24" and spray glued it to the print. I didn't use glass partly because its expensive and I was a little lazy. As you can see in the pictures below I just stapled the back to the frame. Even without the glass, I think it came out pretty well. Another project completed to go in the mountain house....

We had extra space in the backyard and I always wanted somewhere cozy to sit. Of course, the 'conversation' sets you find in stores were out of our price range so we turned to Ana!!

The whole project took a long weekend to complete - including shopping, cutting, sanding and putting it together. The cushions took a bit longer because they were custom made.

The project was much easier than I expected and the result is fantastic (in my opinion, of course!). I can't believe we actually built a piece of furniture!!

Thanks Ana!

Beautiful media center, couldn't resist building it for our living room! Thanks Ana for such awesome plans!!

Our home improvement store didn't have non-pressure treated 4x4s so we screwed 2 2x4s together to make the posts. We chose not to put quarter round around the posts, but instead added baseboards to the front and side to finish it off. We're really happy with how it turned out.

I followed the plan exactly. I did have to improvise attaching the footboard to sides.

This vanity is an amalgamation of a few ideas I found online. I used the Reclaimed Wood Console Table as a guide to pull it all together. All three drawers are functional. The plumbing falls directly between the center and right drawer, and the drawers are mounted on bottom center glides.

When the neighbors came over and looked at this, they thought it came from pottery barn. I knew it reminded me of something, but I couldn't put my finger on it. This picture is about 2 years after I made it.

This was my first large project. Built it in one very long day and then finished over a few weeks. Instead of 2x4's for legs I opted for a 4x4 post with a bolt running through. I didn't really want to figure out the square washer so I just went with standard round. I spray painted all of the hardware silver with Rust-Oleum Universal Hammered Spray paint to coordinate with the Tolix like chairs I purchased from Restoration Hardware.

Made with Western Red Cedar 1x6 fence boards and 2x4. Finished with General Finishes Arm R Seal. 

Thank you Anna. 

I made this with oak plywood and used a straight edge and paper knife to score it to look like planks and a chisel to vary board lengths and stained it. This is the first house I made like this. I made second house like this after a house fire destroyed the first one. My people were well pleased with both of them. I will put lights in the next one.

I'm not sure that anyone would want to build this table, but I attached my plans made in PowerPoint here.

We have a 600 square foot apartment. We enter through our kitchen, so we wanted a dining table that did not take up much space visually or physically. The Squared2 Dining Chairs inspired the creation of our Squared2 Dining Table. We appreciate having it.

To cut down on cost, we purchased 1/8" plexiglass and cut to fit our table top.

This is a ocean/mermaid version of the sweet pea bunk bed. I had to add an additional section above the original plans in order to accommodate for the slide. I also forwent the bottom storage and opted to just put a bigger door, which allowed more headroom inside and the ability to put both a mattress and box spring on the bottom bunk. I used real shingles and painted them gold. The slide came from Home Depot. The octopus door handes I got off of Etsy for about $5 each. I found a doorbell on an old plastic outdoor house set laying around. I added some seaweed from Joann Fabrics. The steps are made out of 2x6 boards vs 1x boards. I also changed the plans so both beds are full size instead of twin size. The top bunk has so much support...it was tested with 600 lbs up there and held up fine!

Shopping for bedroom furniture, my spouse found a bed that was way more than we wanted to spend. After finding this site, and a bit of convincing he finally agreed to try building this. Now he wants to build everything! We now have a long "to do" list of plans we want to try.

Farmhouse table made from 100 year old wood. The wood was taken from a porch at my great grandmother's house in Vernon Parish, Louisiana.