Modern Adirondack and 2x4 Sofas
![](/sites/default/files/IMG_20200628_154533.jpg)
Thanks Ana for your easy to follow plans - I made the sofas and coffee table two years ago, and added the Adirondack chairs in June.
![](/sites/default/files/IMG_20200628_154539.jpg)
Thanks Ana for your easy to follow plans - I made the sofas and coffee table two years ago, and added the Adirondack chairs in June.
My husband built me a potting bench and I painted it with leftover house trim paint. We did make it several inches wider and added a middle 2x4” under the top surface slats to help with bowing boards. I added iron hooks for tools. Love it!
I made this for my boys and they LOVE it! I opted for a square top, since the flower would not have gone over well...Plus I found a square top for $1 at the Restore and who can pass that up, and the legs were free. The rest of the wood was from the Home Depot Cull bin or furring strips. The chairs didn't get rounded (no jig saw) and I didn't add a hole (not a big enough drill bit). But my boys love them and use them all the time!
Thanks Ana for such great plans!
Check out more at http://mylove2create.blogspot.com/2012/10/diy-kids-table-and-chairs.html
I had a good time with this project, and I learned a ton!
It took me a very long time (months!) because I had to work on it during nap time, and I had a baby before it was finished. There were times when I thought it would look terrible, but my husband assured me that after sanding and painting it would be fine - and he was right!
I had to modify the plans slightly (ladder in front) so the bed would fit in my daughter's tiny, tiny room. I also made the door and front window a bit larger. If I were to build it again, I'd make the railings higher as well - the mattress we bought is pretty tall, and there's only about 5" of railing above the mattress.
My daughter LOVES the bed! :)
We have been eyeing this table for years now...finally the military has brought us to the east coast where we have room to do some wood work hobbying! This table is sturdy and beautiful. Love that we can break it down into so many pieces for our moves. Thank you Ana White!!
Wed, 05/08/2019 - 14:49
Can you please link the original design plans for this table? I really like it!
I built the 8 Foot Picnic table off of Ana's plans but didn't do the greatest job following the full directions. I was going a little too fast. The area I most regret moving too quickly on was the legs. I neglected to look at the sketch of the table legs with dimensions close enough to see that the spread for the bottom of the legs should be 47-1/4" and that the top 2x4 should extend beyond the top of the leg by 3". I only looked at the note "meets at corner" and built the legs off that. The legs were thus, not uniform. The next error I made was not measuring my 2x6 boards to make sure they were equal. All were longer than 8' and none were the same length. When I started attaching the unmeasured, uncut boards to the table legs, I attempted to attach them per plan but ended up with a table slightly out of square. Overall though, I am generally happy with the table and will be donating it to my church. If I build more in the future, I will make sure to space my legs correctly.
60 inch version. Sir Duke chalk Paint color from the blue box store.
Rich
This was my first build! I made this kitchen for my 2 1/2 year old son, and he LOVES it! I used the Kreg Jig which made it super easy to build. It was the finishing that took the most time. That and I had to squeeze the work in during naptimes and bedtimes.
I followed the plans for the Simple Play Kitchen and also the Old School Fridge. I added 3 inches to the height and width of the sink and stove pieces after reading another post. The fridge I kept the same dimensions as in the plan.
For the accessories:
Fridge handles: under 3$ each at Lowe's, Stove handle about 4-5$
Sink faucet: random plumbing part from the plumbing aisle at Home Depot, glued together and then spray painted
Sink hot and cold knobs: clearance replacement knobs from Home Depot
SInk: pet food dish spray painted
Stove burners: wooden discs from Michael's, spray painted black
Stove Knobs: replacement knobs also found at Home Depot
Stove Light: $5 at Home Depot, it's battery-powered push light, and happened to have a magnet on the back of it, so I screwed a magnet plate in the oven and now it stays in place, the velcro didn't work
Towels and other accessories found on clearance at Marshalls
The building part went quickly like I said, but the finish took forever! But it was worth it to see the look on my son's face when he finally saw it. He loves it!
Fri, 05/06/2016 - 11:50
I couldn't help but get a little excided when I found this play kitchen you have built. I am currently building a tiny house in my daughter’s bedroom and I am working on her kitchen. I have been having nothing but nightmares trying to get a realistic stainless steel appliance look. I have tried stainless steel contact paper and the exact same glittery stainless steel spray paint you tried before. I also ended up with a horrible outcome and had to sand everything back down and start over. I can wait to go to home depot and get the colors you used for your final coats and give them a try. You may have just saved my workshop from a father that might have went incredible hulk on it from one more failed attempt at creating stainless steel looking play furniture... Thank you!!!
I followed the directions other than the hinges in the plans. Those hinges where $25 a piece so I went with a basic hinge and added the soft close attachment. Works just a as well! This was a mother day present and it turned out so nice I hated to give it up.
First project so I followed I plans pretty close. I took the Cut list to Menards lumber yard they got the wood together for me for around a hundred bucks .
I used a Minwax orange stain brushed on polyurethane.
The 1x4's are used for the back had very rough saw marks my sanded everything before I stainded it after I stand it I sanded it lightly to expose some wood and then I brushed on Minwax polyurethane I am happy with the results bright color yet you can still see the wood grain
I wanted an outdoor lounge. My partner had to work so he helped me get started and I finished it alone. He surprised me a build a corner table to complete the look.
I love it !!
Donna H.
I went with a 1x6 on the bottom so that I would be able to display more than just pictures. So far they are working great and I love them.
I used the kreg jig, filled the holes with wood filler and then painted them white.
This was my first project! I took my time, learning many lessons as I went and borrowing tools from friends. Although there are some flaws, I am so proud of these chairs. They look awesome on our front porch and are the perfect spot to relax after work and watch the sun set with a glass of wine. After building the first chair which fit my husband (6'3" tall), I decided to slightly change the angle of the second chair such that the depth better suited me (5'4" tall and short legged). Thanks for the inspiration Ana, I can't wait to start my next project!
wife wanted some new tables.
I picked up wood working as an indoor hobby during the Coronavirus and working from home. I was doing everything on the floor in my garage until I saw these plans for the Pony Wall Workbench. I'm 6'4 so having a bench to work at is such a savor for my back. I didn't have as much room, so I just used the 8 foot section and dropped the miter saw into the middle, two drawers on either side. I'm a big golf fan as well, so I spiced it up with some old golf balls I had laying around for drawer knobs!
I really appreciate this site and all the plans. I'm looking forward to many new builds, not on the ground haha!
As part of my backyard overhaul I've added an outdoor shower and chalkboard against the wall of the house. There's also a small sand pit and deck area, so the shower comes in handy to wash the dirty feet. I had a few pallets sitting under the deck for years and finally put them to use. Some cuts here and there and some sanding and they look great. For the floor mat I just cut the pallet piece you can see in one of the photos in half and framed it with treated 2x4". The chalkboard is a plain sheet of 2x4' project board primed and painted several coats with flat black exterior paint. I used this over the 'chalkboard' paint because it's exterior grade. It works great, even better than chalkboard paint imo. The frame is made of the cut slats of the pallet, just glued and nailed on. The fence also is a cut pallet. I just made random cuts about half way through on varying angles which resulted in two mirrored halves of the pallet. They fit the space perfectly. I love the random look of it and may give it some paint eventually.
Built this from the mini farmhouse bedside table plans, but decided to use the lathe on the legs (which also added a lot of time). This was one of the first furniture projects I've done and it was pretty easy to follow the plans.
Thu, 01/12/2017 - 10:15
adorable! the turned legs add alot of character too!
I'm a high school teacher and like flexible seating. I needed something that is very sturdy and can take a beating from teenagers. I used Ana's "2x4 Outdoor Sofa" plan, made it longer, added some extra braces, and here it is! My new classroom couch.
Julie Stanfill
I built this console for my living room. I love the style and the color of the console of shanty2chic and I wanted the same.
Thanks for the plan and inspiration.
Sun, 09/01/2013 - 06:46
You did a great job! Any tips or hints about steps that you may have done differently from the plan, or found challenging or got you stuck?
I modified the legs to fit a counter height table
I made the seat 25in tall to fit a 36in table...
Changed the top a bit, but otherwise matches the plans.