Community Brag Posts

I saw this at the perfect time for deciding to make one for my niece for Christmas. It was too cute of an idea to not make!! She turns 3 at the end of January and it's perfect-sized for her. From what I hear, she threw a tantrum when her parents told her she had to stop playing with it because it was naptime! I'm hoping that she will share with her brother when he's older (he's about 7mos now) and they can play with it together.

I apologize for the lack of pictures, I got the buntings done about one day before we had to pack it up to head out for the holidays, so there wasn't much time for pictures!

For the hutch part, I attached each side with bolts and wing nuts so that it could be knocked down for transport (especially since we have smallish cars and had to drive an hour to gift it, and the recipient had to drive 2 hours back to their house!). I added some holes just under the dowel (lining up with the holes in the base when knocked down) so that it could be connected again as a shorter version for transport. This actually worked out pretty well and you can almost use the dowel as a handle when it's like that. The only issue I ran into with that was once I put the lower velcro on for the theater curtains, they would hit when trying to collapse it and we wound up losing one in transport.

Buntings weren't too hard, but I've been sewing much longer than I've been building! I did have some issues getting the theater curtain to lay right.

This table was made with already turned legs purchased at HD, one 4 x 8 sheet of oak plywood cut into two 4 x 4 sheets, pine for the cooler supports and edged with 1 x 3 oak routed with an ogee detail. Table supports were attached to the legs using pocket holes. Legs and supports were attached to the table bottom using pocket holes. The opening for the cooler was cut by plunging a circular saw from the top.

I loved making this chair for my granddaughter! My pug is for size reference! Thank you Ana White!

This plan isn't an Ana-White, but I wanted to share due to the low cost. I'm sure many of you are like me and are about tired of building on the garage floor.

(I'll be posting more projects soon)

I modified the plan slightly by making a thicker top (doubled the OSB and some 1/2 plywood I had around the garage for a smoother surface.) and 1 x 4 furring strips for trim around the top edge. This gave a very sturdy setup and matched the height of my table saw, making this my outfeed table when needed.

We decided to make loft beds for our girls room to offer them more space and also give them some individual room. The old room had daybeds that just took up so much of the room.

I saw the hanging beds on this site and thought they would be great. So I got to work.. I used 1x4 s for the platform to lighten the weight of the bed. I had to customize the sizes a bit but that wasn't a big deal. I used the Kreg jig to joint the 2x4s as well as on the rail posts. They are attached below the platform to the front 2x4. We also used chain rather than rope as chain doesn't give.

We are really pleased with the results. The girls love them. Each has their own desk space now, they shared one before, and their own storage space.

Cost us with all wood, supplies, hardware, paint, about $150-175

Made exactly to the plans with the exception of the middle 2x4 between the legs. I used 1/2" threaded rod, some steel rings welded to the rod, and a double sided clevis to make the connection in the middle. 

These bunk beds are a big hit for daughters, nieces, granddaughters, and even full grown kids. After making a few as gifts, I decided to make three at once and cover several birthday parties at once.

The plans were very well done and I just followed along. Worked great!

Thanks for the plans!

Peter

p.s. I put that these take more than 20 hrs, because there's a lot of gluing and waiting time while doing the guard rails.

p.s.s. An old pillowcase is the perfect size for material for the mattresses.

Finally having a house meant that we could finally have family over for holidays, parties, etc. The problem was that we didn't have a table large enough to accommodate more than 4 people comfortably. When I saw the plans on here, I knew it would be the perfect fit for our home which is turning out to be a little bit rustic, a little industrial and very eclectic. While my dad has done some woodworking projects, they have mostly been easy shelves or home construction, nothing like this project. We built the table and built the matching 8ft bench out of approx. $95 of construction pine lumber. We changed the table lumbar from 4-2x10s to 8-2x6s (cut down to 5" width for cleaner edges). My dad did most the construction and I completed the finish. I sanded to 220 grit. We used SamaN Water-based stain in Black (I love that stuff, so easy to use and re-wets so I didn't have any lap marks, although it did wipe off some when I applied the poly) and ZAR Ultra Max waterborne oil-modified polyurethane. The grain raised even more after I laid on the poly. I love how the pine created a reverse grain and has such great texture. We made some modifications, one being that we did not attach the table top to the base. Instead, we added some wood to the bottom of the table to brace against the brace and legs. The table top is so heavy that is never moves and will make it easy to move since together, the table and brace are too heavy for 2 people to lift. Some of the things we learned: always double check the measurements (the base braces were about 1.5" to tall), if at all possible, create a jig to keep the leg pieces square, be careful assembling the base (we cracked one of the braces), and let poly cure for at least 24 hrs even if none of the literature mentions it. If we had the equipment, we would have loved to use a planer and a joiner, but even so, I think it came out awesome. It only took 40 years, but I think that our first father-daughter woodworking project has been a great success. Can't wait to work on our next project!! Thanks Ana-White & Shanty 2 Chic for some great plans!

I wanted my top to be a lift top, so I used 1x3's adding breadboard ends. I ordered the lifts from Amazon. I applied a single coat of stain and then sanded it down to give it a more rustic look before applying a satin poly coat.

A. Henry

This is a mini version of the Laundry Basket Dresser that fits 2 baskets instead of 3. VERY easy to do!

Thanks Ana White for creating such great plans! This was my first furniture build and I must say I am so happy I did it! Our living and kitchen area are now complete (finished mine just in time for Christmas) which was a life saver! This table can hold a lot of decor and cookies!!

Have yet to get the hardware spray painted and attached - but even with out it looks amazing (already have been asked by 4 friends when I can build them one). We decided to go with Grey Stain and a satin poly.

Changed the scale of the front panel and the window trim slightly.  Added window boxes for a drink, toys and book storage.

We just finished building this room and decided to finish it off with Ana's loft bed. It's mounted at height of 6 feet in order to accommodate our 18 year old.