Community Brag Posts

I used flat stone and a masonry circular blade for the base of the corner posts. I also used 2 x 4's for both layers of the top boards. It was a lot of fun to build.

This is my first Ana-White project (first furniture project, for that matter). I used the Farmhouse Bed as inspiration and modified the headboard / footboard to be a little taller. Other differences are that I used larger side railings (2x10) and left off the decorative tops of the headboard / footboard. Pocket holes hide all of the attachments, and I found some amaing bed rail hangers so the bed can easily be disassembled in case we move. It's super sturdy and my wife is happy (the most important part)!

My wife liked the PB Larking High/Low table, but I didn't like the price. Took about 3 weeks of evenings and weekends.

Used 3/4" MDF Panels for sides, bottom, and top
used 3/4" select Pine for face frame
used 3/4" smooth plywood for drawer faces.
cut additional pine strips at 15/16" and then routed one edge for trim work around drawer face.
same process for right side door, but added 1 1/2" pine to trim along sides and bottom
Attached 2x4's to bottom of table and then covered with MDF panel for skirt.
Skirt is an 1/8" raised from floor to give space for carpet and not cause stress on skirt
used a jig saw on front of skirt for cutout
used decorative molding for under the table top lip, you'll need to figure out your overhang for whatever molding you use.
Used MDF for the changing pad holder. about 3 inches tall and then cut to dimensions of pad.
Topper on the right is just a miniature of the full table, from a contraction perspective.

My dimensions are slightly customized from the below.

Changing Table
Overall: 55" wide x 21" deep x 44" high
Dresser Cabinet: 15" wide x 19" deep x 23" high
Dresser Drawer (3): 31" wide x 18" deep x 7" high
Small Top Drawer (1): 11.5" wide x 15" deep x 5" high

Topper
Overall: 34" wide x 17.5" deep x 3" high
Topper drawer inside small cabinet: 16.5" wide x 11.5" deep x 5" high

Great outdoor project.... Kids loved helping too....

My husband modified these plans by making it a 42" tall bar high table. He built it and I stained it with Dark Walnut Danish oil and it came out better than we imagined. Thank you for these awesomely cool DIY plans.

Again I'm sorry I have no plans, but what I do have is a great instructional video. Drawer slides are such a pain to install without the right tools. I'm sure you can find great dresser plans but the kicker is how you install the drawers. These inexpensive drawer slide mounting tools might save you from going insane. Check them out. http://youtu.be/vI3jgkhxxPE

I built this 10.5' farmhouse table for my aunt and uncle's dining room. I modified the plans slightly to try and look more like the Restoration Hardware version, using 4x4's for the beams and side supports and rounding the sides of the side supports. I also modified the top by adding an extra sideways board in the middle. The rationale for this was that I was worried about finding boards at the length I wanted that were perfectly straight from end to end, so by adding the center sideways board I only had to find boards that were perfectly straight for about half the full length. Also, we liked the look of the extra board in the middle. My little cousins had fun helping me distress the wood with hammers and other tools laying around. We love the way it came out, thank you Ana!

With a third baby on the way, they may not be enough room in this one for much longer, never realized how many they had till be put them all together.

My husband and I were inspired by Ana's plans, but needed to use up some wood we had laying around the garage because it was starting to bend and warp. We made the large box 2x6 ft and the smaller one is made from scrap and is about 15in x 2.5 ft.

This is the second project I've completed and I'm very proud of it. The design was changed just by adding four legs instead of three. It took me awhile to get the color even. Sanding between coats of the clear coat semi-gloss finish would leave white marks/residue that was difficult to clean away. I would have to restain those sections with a swift wipe on/wipe off action. This made the color deeper but also richer. During the summer months, the bench will be outside but will serve as indoor seating in the winter.

Rustic X end table

The original plans make a pretty big coffee table (52" wide).  I made this one (32") with the left over pieces of 2x6 from the bigger one. It was fun to make and is great for someone with a smaller living room

My dear husband built the bed and I painted it. He found that it was easy to make. Thank you Ana, we love it. We are waiting for our new mattress!

I was looking for inspiration for the grandchildren when
I came across the full size version. I have now made 3 of the 1\3 sized as pictured, in different colours. It takes longer to paint them than make them.

First table I've built. The Rustic X Console Table was fun and fairly simple. A little complicated since we live in Hawaii and decent cheap wood is difficult to come by. Makes my entrance way very inviting. 

Needed to get the girls Dresses out of the nursery, this will work.