Community Brag Posts

I built this crib and changing table using the DIYstinctly made crib plans and the simple changing table plans from this site.  The tartan design on the shelving is the product of LOTS of painters tape.  A word of warning: if you decide to build this crib, buy your matress first and cut the rails to length.  I had to remedy a gap of about 6 inches at the end.

Potting bench I built for my daughter.

My mom asked me to build her a buffet to match the Provence style dining table I built her a few months ago. I used the Providence Table plan as a jumping off point. Here’s a quick breakdown of the changes I made to the plan:
• Supply list – 3 2x6x12′ boards for the top
2 2x6x10′ boards for the shelf
5 2x4x8 boards for the legs and supports
• Design – I cut the legs to the same dimension, but flipped the legs 90 degrees so the profile matched the table’s. I placed the leg support 4″ from the ground, again to match the dining table. I added a shelf by drilling the 10′ 2×6′s down onto the leg supports, and used scrap 2×4′s under the center to keep it from dipping. I nixed the center top support, and decided to keep the cross supports at the same angles and length, but doubled them and used scrap 2×4 cut at 18″ wide (the width of the buffet) to span the three boards so the center wouldn’t dip or warp over time.

We chose cedar to match the table and cut down on chemicals, but it could cost a lot less if you used untreated pine for indoor use. Either way, $120 for a twelve foot long buffet isn't too shabby!

I built this for a silent auction at my school. My students chose the theme. Each of the kids in my class signed the white legs. Super easy to put together after following the plans to cut each piece of lumber. The painting was another story thanks to those stars!

I was thinking of buying the conversion kit for my son's crib when I came across this bed. I modified it a little but used the base design. It came out great and this was the first time he saw it and got in it. Now all we need to do is figure out how to get him to use it! 

I retired from law enforcement and took up a new hobby. Your plans have helped me learn to build. This is a tv console I built for my sister’s new house.

We just slightly modified the plan to accommodate our really great industrial sewing table base.

A great weekend project...the "love swing"! I used the plan from Ana for the swing seat and added two arm rests from left over 1x6, rounded them off and sanded.

I cobbled together an A-frame to hang everything, made from five 8 foot 4x4s and two 8 foot 2x6s laminated together for the stretcher. Assembled with 1/2" galvanized carriage bolts and hung with 1/4" chain.

Definitely going to want a good miter saw for the A-Frame angles (the top ones are a bit tricky to get everything lined up)

Love it! Thanks for another great plan Ana..and of course..Shanty2Chic!

I’m an avid boxer and wanted to be able to work out in the convenience of my garage without making too much noise, and still make it easy to carry out normal garage functions (workshop and parking the car). I came up with an original design of a speed bag platform that locks away in a raised position, completely out of the way for normal garage usage. Then it unbolts and slides down when ready to engage. I also used rubber dampeners where I mounted it to the ceiling rafters to reduce vibrations and cut down on noise travelling through the house. 

I documented the whole project in my blog post at http://www.justmeasuringup.com/blog/diy-boxing-speed-bag-station-that-stows

I work on a lot of projects in the garage, and having a speed bag right in the middle is a great way to take a short break in the middle of it all - or when I bang my thumb with the hammer and want to release some anger :)

Thanks to your clear plans it was easy to make these two chairs from scrap 2x4s. Found the cushions at Lowe's. I'm a grandfather with eight grandchildren live in Iowa.

We love the medicine cabinets that are found in 5 star hotels and had come across a blog (Batchelor's Way) that had built one very similar. We decided during our renovation that we wanted one, too. In the photo you can see that we still have to install the light fixture, which fits perfectly within the high top molding, and the vessel sink and wall-mount faucet below.

This was my first attempt at building something with doors- the one on the right got knocked off square at some point and required some finagling to get it to fit. As a result, there's a gap above it, but it opens and closes smoothly. I'm okay with it. It's not perfect, but at least it's MY not perfect.

This project was very straight forward and fairly simple.  The only big changes we made to this:

-Used solid wood paneling in place of plywood.  We are now fans of using this stuff over plywood (For furniture building)

-Made the top drawer faces flip down isntead of building drawers

-Added roller catched to all drawer faces to keep the kids from gaining access

-Added a 1x4 on the back to have something solid and easy to strap our tv to

This is now our favorite piece in the whole house, very funcitonal!  Thank you for the plans Ana!

You can see more pictures at: http://gingerandthehuth.com/2016/08/restoration-hardware-tv-console/ 

Inspired by a photo on a DIY site i made this simple stool from pallet wood. No plan, just an idea, and i know that the hight should be around 20".

Build this bench for our dining room. Had some left over stuff and got a 11 feet plank for free at the lumber yard.
66 inches long, 14 inches wide and I made it a little higher, 19,5 inches.
Have a weakness for red benches :-)

My new handmade Rustic Console, made from 4x4 Douglas fir, 2x4 pine and 2x6 pine wood. This stained using leftover stain from Minwax Expresso and Special Walnut and mixed them together and created a deep golden dark brown color with made the grain texture stand out more. Then I applied Varathane Polyurethane to protect the finish. The entire project was fairly easy besides the angle pieces on the legs since my miter saw only can achieve a 65 degree cut. I ended up creating a jig to cut the angle pieces.

44in long X 15in wide X 33.5 in high

More pictures available on my Facebook:

https://m.facebook.com/Ngo-Inc-912298105544682/