Farmhouse Table
My husband built this table from the Farmhouse table plans. Just changed up the top somewhat. It's beautiful!
My husband built this table from the Farmhouse table plans. Just changed up the top somewhat. It's beautiful!
I'm making this for my wife, I added a little Riser on the back because it won't be leaning up against the house and I didn't feel back was high enough.
If you find yourself in the 6-foot range I would recommend increasing the leg height and adding a 4th 2x6 or even a 5th to increase the bsckrest.
My daughter found this plan on the Ana White website and now, we have made 3 tables total. Pictured is the 2nd one we built together and is currently in her house now.
My husband I built this kitchen set for my daughter's 2nd birthday. She just loves it. For the sink I used the same plans as the stove and changed them a little. There is not enough room below but we used the Cute Play Pie Hutch plan too. The double door fridge we use as a pantry. I can't find the plans for the fridge but we used Ana's plans for that too.
I admired this project the first time I saw it, I thought about building it for a few months and got the opportunity when my Fiance left town. I completed this project in a weekend with a had from my friend (more just to hold the pieces where I needed them). I had previously built her a hope chest out of a Rare and Beautiful tongue and groove pine, I used the same wood for the head and foot board so they would match. Overall these plans were great, I changed a few things to make it a little more what I wanted. I made the foot board 24" in height with a total of 20" of tongue and groove. I also used some wrought head nails to give a little more character to the piece as well, you can find them here, http://www.rockler.com/product.cfm?page=1152 . I wont do too much to the piece, more than likely just add a couple coats of shellac to match the previously mentioned hope chest. I hope you all enjoy this project as much as I did.
Wed, 07/03/2013 - 08:44
Did you need to pre-drill the nail holes? I am worried the wood will split with these types of nails. Thanks
Thu, 07/11/2013 - 12:36
Yes you do, I made a jig so I knew all the nails would line up with my wood and be in the same place. The bit was half the size of the nail, they are really just for a decorative look. Good luck with everything.
In reply to Yes you do, I made a jig so I by capecodfarm
Thu, 07/11/2013 - 12:51
I figured out my biggest mistake was not lining up the nails with the grain of the wood. Once i had the nails lined up in the right direction they went in mostly without a hitch. One of the panel boards did split but was hidden by the 1x4 face board. Thanks again for the idea and i'll post pics when completed.
I adjusted the plans to make this a chair that would fit under a regular table. The front legs are 19" and the back legs are 40". Then I followed the plans as written.
Hi, I built this wedding Arbour for my daughters wedding a while ago and unfortunately, I have no plans as I built from my head. It now sits in pride of place within thier garden as arch for thier garden.
I built this with a drop saw, hand saw, router, drill and hammer only.
I follow Ana's plans every release and save her plans for when I retire in two years to build for our house as well as try to run a small business from my shed.
Thank you Ana for you continued plans and wonderful advice.
Tue, 10/05/2021 - 10:40
WOW, such a sweet gift and reminder of their special day! Thanks for sharing:)
I built this entire project out of the scraps from the closet organizer and a 1×2 that I had. You could use the metal brackets Ana suggests, but the 1x2s are working great for me. The wheels are from an old rolling Target TV stand.
We used two tracks, instead of three, because I do huge loads of laundry in my front loaders. If you want to do the closet organize and this, do the closet first.This will be a free project. That's right, $0 out of pocket! Oh, and the top is scrap wood, just glued, and screwed (counter sunk).It made for a more finished “island” look. This step is completely optional. It's just for looks. I would love to add a towel bar to the side of this and a bracket to hold my iron too. The mini ironing board does fit on top!
I made these for my Mother's Day present to myself. I painted them the color of Carrots and Lettuce. Working on the third one titled "tomatoes today." Easy to build, fun and quick....
Sun, 05/19/2013 - 18:38
Love the colors! What a good idea! They look wonderful!
I modified the dimensions slightly and opted to not mount the fold down doors as I figured they would always be open anyway. I built this mostly from solid red oak save for the bottom panel and the middle panel, which are plywood. I crafted the top out of 5 pieces tongue and grooved with mitred corners on the front. I also tongue and grooved the doors with glass insets. I finished it in Minwax red cedar under poly.
Ana I’m new to wood working and I really love your plans. They are so much easier to follow than a lot of other plans that I’ve seen. It makes me feel like I can build almost anything. Thank you.
Brandy
I really wanted a sewing table/desk for my office but wanted something that could be repurposed in a few years when we move. I chose the Narrow farmhouse table plan because it was a really sturdy plan that was easy to modify for our needs and was a timeless enough style that I can use it in another room if need be. I especially loved the look of the legs.
We made our table smaller to fit our space and also made it about 1 or 2 inches shorter because I’m really short and wanted a comfortable place to sew and craft. The top of our table is 58″ by 24″. We used MDF for the top instead of slats because my kids use this as a craft/coloring table when I’m not sewing. I didn’t want their pencils to poke through their papers if they got caught on the slats. We used thin molding for the edge of the MDF to give it a nice finished look.
Check out the details about how we build the bed on my blog: http://www.brightgreendoor.com/2013/05/diy-ana-white-jr-loft-bed.html
Although nothing about it was difficult, it was time consuming, and consumed the greater part of two weekends.
We followed the plans on Ana White’s blog pretty close, other than narrowing up the stairs by a few inches due to a furnace vent that would have been in the way.
We bought all of our boards at Menards which came in just under $100 including the large piece of plywood. I spent chunks of time throughout the week getting all of the boards sanded. Then we spent a Saturday getting all the boards cut to the proper size. Then it was a week full of giving all the wood 2 coats of Bulls Eye primer and a top coat of high gloss cabinet paint.
I also installed the Ikea Kvartal track system around the inside of the bottom bunk. I used leveler clips from Ace to hang Ikea curtains that I altered.
My boys were SO excited the whole time we were building it and love it. My little one calls the whole bed his “top bunk”, even though he sleeps on the bottom. They also have dubbed the area under the platform the “hideout” and think they are invisible when they are hiding in there.
Fri, 06/21/2013 - 18:46
These are awesome and I think it's so smart you stained them after you cut them and before you drilled them! Thanks for that time saver! Question? Is the bottom bunk raised or did you raise the height of the planned bed? I want to make ours a bunkbed too, but don't want it to be too tall.
Thanks
I adjusted the measurements to make it longer and wider. I also looked the original Pottery Barn trunk and tried to copy the multi color finish. I had so much fun building this!
In reply to This is truly gorgeous! by Ana White
Tue, 04/28/2015 - 12:05
Thank you, Ana! Your comment means a lot to me! =-)
Tue, 04/28/2015 - 12:07
The handles are from Ace hardware--I had to spray them antique bronze since they only had them in silver. I stained the trunk is dark walnut from minwax and then used diluted paint in barn red and teal to spread some color here and there. Finished with some polyurethane in satin (spray). That's it!
Tue, 12/25/2018 - 19:42
I don't know if you will check the comments on this brag post since you posted almost 3 years ago, but I'm also curious about the hinges to use. I have watched some youtube videos that show how to chisel out a space for the hinge, but I know there must be an easier way and an easier hinge to put on this box.
Thanks so much ,
Apryl
We wanted a patio table to fit up to 10. Done with a mix of pocket holes & 1/2" hex bolts. Made small changes to the stretchers. Moved them inside because we liked that aestetic better. We made the top longer because we didnt want to do the breadboard ends. Used big 4" hex bolts & washers and painted them with "hammered steel" paint to give them a more vintage look.
Will be making the matching benches next. We wanted the benches to fit perfectly underneath the table for storage, so Ill be cutting the bench seats to fit under table leg to leg.
Built the Helper Tower for my grandson. It's the optional hinged version. He uses it every time he visits, and will get a lot of use out of it - platform is at its highest setting.
Mon, 10/04/2021 - 16:51
This is such a great way to include the children in learning and fun! Thank you for sharing, it looks amazing!
This was my first furniture building project. I made quite a few mistakes along the way, but I'm happy with how well it turned out. This project took me ages; I'm amazed that people can pull it off in a weekend! I made the table slightly lower and narrower than Ana's plan. It comfortably seats 6 people. I'm so grateful to Ana for her plans, and I also found the instructions at the tommy & ellie site very helpful.
Mon, 01/20/2014 - 14:25
Your table looks amazing! I am going to start my farmhouse table this week and I've been trying to decide on the color. I think the dark walnut looks awesome! Great job.
In reply to Your table looks amazing! I by tricia.flores
Wed, 02/26/2014 - 18:52
Thanks! I couldn't decide easily either. Good luck with the table :)
First project my husband and me attempted- turned out awesome! Very sturdy bed. The metal frame and box springs are not attached, it just sits inside the wood rails, headboard and footboard. We worked on this a few hours at a time on Saturdays and Sundays for one month since we work full time. Definitely more projects to come!
My oldest son grew out of his twin bed and we found the plans for the Cassidy bed and thought it'd be perfect. He couldn't think of a " theme" for his room so we decided to make the headboard taller to keep from having a "blank wall" to have to decorate. It turned out great! We used Colonial Maple, American Walnut and English Chestnut stains for the shims & Colonial Maple + Kona for the border. This was my first time building a queen bed. I am so excited with the way it turned out. This project was so much easier than I had anticipated. It took about 3 days for me because we had triple digit weather and that limited the amount of time I could work outside. I needed help with the final assembly, but other than that, it was a breeze. Thanks again for the awesome plans!