Community Brag Posts

This was my first project using plans on this site. It was relatively easy and a joy to complete.
Everyone loved it!

23" wide by 21 1/2" high by 15 1/4" deep

I needed a little bookshelf to fit under my window so I went with one full shelf (11 1/2") and a baby shelf (3 3/4" not including the area behind the top front lip - it's 5" from shelf to the bottom side of the top surface)

Now, to get around to putting on some stain...

Plans were great, thank you. We made our table a little deeper to accommodate 3 to 4 little ones, and purchased some little chairs at IKEA. 

We followed the plans for this table that will sit behind our sofa in the main room. We've never really built furniture before, but this wasn't too difficult to make and I love how it looks. Plus it's super heavy and sturdy, so it will be perfect to store items and decor for the main room.

One of my friends at work is going to a new job, and this build is her going away gift. It is a variation of the Fancy Jewelry Box, with the following modifications:

Made from select pine, no plywood is visible on the outside on this build.
Slightly smaller, the box is made from 1x6, the back is a ½” x 5 ½” craft board, and the door outsides are 3/8” x 5 ½” craft boards.
The drawer boxes are ¼” thick craft board and the doors and overlay drawer faces are 3/8” thick craft board.
Overall dimensions are 13” wide, 5 ½” deep, and 14 ¼” tall.
The select pine worked very well for the luxe stained finish I was trying to achieve.
Used fancy knobs instead of wood knobs (also swapped out the included screws for shorter ones).

I really took my time on this to get everything just so. The project took about 15 hours in total, including the build, finishing, and decorations - - a bit at a time, spread out over the last couple of weeks.

I'm very happy to say the gift was a big hit!

I built this bed frame with the general guidelines for the queen sized farmhouse bed. I adjusted some of the dimensions to better suit our layout.

I made a smaller version of Ana's trash can for outdoor use. I used scrap wood that I joined with the Kreg Jig but I think it would have been easier to buy the size she recommends (but this was free!) We are always walking our dogs and then stuck with bags of poop and no where to put them. They end up in a pile near our door (GROSS.) so I built this to 'house' the dog poop until trash day. It's enclosed so there's no odor when you walk past it, and it looks much better on our front porch than poop bags. I painted it to match our front door so it looks like it 'belongs' up there. Ahhh, much better.

Farmhouse bed!!!

My new garage shelves.  Not my first project, but I really liked the way they turned out.  Used 1/2" plywood at 16" width.   I attached the plywood with wood glue and 2" brad nails every 12 inches.  I used an impact driver to screw the 2x4 into the wall and to attach the vertical legs. Saved a lot of time and wrist fatigue.

Had to adjust the measurements to fit the space I had to use it in my tiny kitchen but it turned out pretty well.

I've looked around for a crib for my son who is very manly, and also has a baby doll. All I could find were pink or purple or floral cribs which led me to the Internet in search of Plans to build my own. I found your site and love the crib that you built for Olivia. This is our manly version that my son and I completed today. Thank you!

Really enjoyed this project, thanks for the great plans!

I love the C&B Big Sur dining tables and was excited to come across these plans. I tackled making a copy of the Big Sur dining table using Ana's plans as a starting point with some modifications and custom dimensions (4' x 4' x 31"). This was my first major woodworking project and I wanted it to be as nice and strong as possible so I tackled joining the rails of the frame to the legs with mortise and tenon joints. The main reason I did this was because I used 1 1/4 and 1 3/4 red oak for the entire table and I just wasn't convinced screws could handle the weight of the top on the frame. I also wanted to learn how to make those joints. I used my plunge router to cut both the mortises and the tenons and it worked out reasonably well. Now that I have a table saw I will be using that with a dado blade for tenons in the future. I sanded to 320 grit and finished with four coats of General Finishes Gel Stain in Java followed by four coats of Minwax spray on polyurethane. The last step was to apply paste wax using 0000 steel wool and then buff with a clean rag. I love the way this came out and am now planning on making a bar cabinet with wine bottle holders in the same style. The total cost of the table was on the higher end than I'm used to because the wood was pricey but it was still so much less than the C&B Big Sur price tag. I'm lucky that I have a hardwood lumber supplier just a few minutes down the road that does custom milling of 100's of different species.

I finally have order in my garage! I built a mobile lumber rack using plans from the Rogue Engineer. My husband and I knocked out this project one Sunday afternoon. It can store a huge load of lumber and best of all, it’s portable. We are very, very pleased with the final project! Storing all our lumber on the rack has freed up a great deal of space in our garage.

Thanks for the free plans made some modifications.  Sharing for all....Have the assembly line going as gifts to my Oklahoma University friends...Personally I am Oklahoma State University....but was a Wine-A -Dirondack among friends....

This is the cabin single bed. The bookcase/drawers and desk are almost done and will be posted soon. This was a great project, very easy and my son is so excited! Thanks again Ana :) We used a green milk paint with Federal Blue milk paint over it, distressed it and then used a brown glaze and polyacrylic.