Community Brag Posts

This was my first project and I'm really happy with the result. I didn't even make any mistakes! I love it and my friends always ask me to make one for them too.

This was built mainly as a place to bring our pond plants in for the winter. After looking at various kits we decided this was the best option for us and much cheaper.

The size was increased to 12 X 12 and the walls/ceiling were increased another 15" in height over the original plans. An entryway was added to block the cold wind as our original barnstyle door wasn't tight enough and ended up being too drafty. Also added an RV type autoswitching propane system and blue flame heater for backup. For the winter months we insulated the lower portion of the interior walls with spun fiberglass and 6 mil film stapled over it. 

This is a very utilitarian version that serves our needs well. Great original plans and easy to build.

This was my second Ana white project and first complex one.

I learned a lot and look forward to more.

We were looking for a temporary desk to fit in a space next to our fireplace until we can build some built-ins. We modified the width and depth to fit. This was super easy. We love it.

I used the Turned Leg Farmhouse Table Plans for the frame of the table, but changed the measurements to fit the table top from the Farmhouse Table - Updated Pocket Hole Plans. I also saved a little money by using a set of black turned legs from an old kitchen table. 

I completed these chairs about 3yrs ago.  It was a great project and I learned a lot.  I really appreciate this site and have made a sofa and 2 benches as well.  Thank you Ana for the site and I wish HGTV or another station would pick up your DIY show!  

This set of tables is exactly what my fiance and I were looking for. Its rustic knotty look pulls the room together and glows a warm colour when the fireplace is on. Thanks Ana!

My wife and I just purchased a new home with our first dining room. While debating the expense of buying new dining room furniture we decided that we should try a do-it-yourself project and were lucky enough to stumble on Ana's website. While we had never done any real woodworking (we made a cat tree once), Ana's plans and the accompanying comments were easy to follow and proved that even beginners can make cool furniture!

We built the bench first and managed to complete it in one weekend without much trouble. This helped us learn the basics of the tools we were using, especially the miter saw. The table followed.

We wanted a slightly larger table and bench than those in the plans so that we could host more people and fill out the room. Our table is 78" x 38.5".
Increasing the width required adding an additional 1" x 6" on the table top. The only other change that we made was to extend the 2" x 2" on the side of the table the entire length of the table as is required in the bench instructions. We thought that this provided more stability for the bread boards. We used a threaded rods and turnbuckles on both the table and bench for the accent piece between the legs.

While we certainly had hiccups along the way, but we really enjoyed the process, and love the dining room set that we built. It was a really rewarding experience and now we're looking forward to building most of our furniture!

Special thanks the Ana for her plans and website. We couldn't have done it without her.

This took me about 1 1/2 week to complete.  I'm active duty military so my hours are always crazy.... I didn't get this from any specific plans. If anyone needs guidance feel free to get in touch with me.. you can also follow my work here...  

https://www.facebook.com/J0EPEREZ/

Well I have found your site through Pinterest md now I am Addicted. Not only did I make one stool, but now three ( one for each of my boys). I will be finishing them shortly. But since it is my first project I wanted to share and thank you for the plans.

Next up is a sofa table (90% done already) and the media center (which I will float and use as storage for kids toys and double as a window seat)

Anyway, these stools are great, the kids love them and thy will go great in the kids room under the camp loft bed or loft playhouse bed (my next project :)

Modified the main table by knocking down the length one foot. Slightly reduced width based on lumber used by about 2 inches. Added two extensions. Used 2x4s for side aprons and 2x6s for end aprons. This allowed me to notch 2x3 (lumber size) holes in the ends to slide extension arms in. Arms held by friction and torque so if you do this make the holes tight. Don't over stain or poly. Slide wax candle on arms to help them slide in. If lose you can install a latch on arms under table. All items from Home Depot. Last photo shows dry fit of extension prior to screwing on top from the bottom. Gave me best alignment.  If you haven't paid it forward for this great FREE site, do so by ordering Ana's book a Handmade Home. Making the coffee table I found in it this weekend. Good luck all and if you are wondering if you should? Yes, you should. 

I used the plans provided. I made a small change to the windows and made the bigger. 

Super easy project with huge results!

Took us 2.5 hours to build and about 2 hours of finishing work. Be sure to use a square as you position each panel.

Thanks Ana!

Here is my latest project completed. I took the table that belonged to my wife's parents and re-purposed it. Took it apart, stripped it, rebuilt it into a farm style table, and refinished it. Put it on top of a base that I built, painted and distressed. Turned out solid as a tank. Broke bread on it for the first time tonight. It should last for a couple more generations!

Intermediate project. It is not specified how to attach the top but I would recommend using the Kreg Jigg on the outside ends. Beautiful and spacious amount  of storage. 

Made from leftover 16x24 and 12x12 tiles from my daughters bath room remodel and leftover treated 2x4's and 1x6's. The legs and cross pieces were ripped from 2x4 and attached using my Kreg JIg. I glued the tile tops with silicone Calk and ripped 1x6 's for the shelf bottoms and nailed them to the lower cross pieces. Opposite side cross pieces were 3/4 in lower to accomodate the 1x6 shelf to make it even. The width and length of the tables are 1 inch less then the respective tiles to allow a 1/2 inch overhang each of the tile tops.