Community Brag Posts

Queen headboard. Natural finish.

This is a poplar (yellow tulip) chifferobe I purchased off of Craigslist for $40. I included some before and after photos. It was in sad shape. Much of the veneer was broken or coming off. My wife wanted me to add shelves inside. I began stripping off the old finish using liquid stripped and by sanding. I removed the old veneer by using a very hot steam iron and a putty knife. I ordered up the new veneer from veneersupplies.com and new hardware from Kennedy Hardware.

I built the new shelves using 1/2" poplar. I then began putting on the new veneer. I used 22 mil. paperback veneer and contact cement. If you have never replaced veneer spend $10 and get a veneer cutter and another $10 and purchase a scraper. They make the job much easier.

I then began applying the stain which is Minwax Aged Oak gel stain. I had a challenge with trying to match the stain. The old veneer was tough to match the stain with the new veneer. Father time adds his patina so I had to darken the stain. I used Minwax Jacobean stain. I think I got it too dark but since it is completed I like the contrast. I went ahead and purchased some 1/2" rope trim (poplar) and a poplar applique to add to the door. Since the mirror was broken I decided to go ahead and fabricate new back splashes for the chifferobe. I found these on Ebay. A gentleman had bought out these from an out of business pool table company. They are poplar and once I cut them down they really seemed to match. I will use the mirror frame for a later project to make a photo frame.

My wife and I had wanted to put this into our bedroom for extra storage. We didn't realize that we couldn't get it into the bedroom due to a narrow hallway. It ended up in the kitchen/dining room as a buffet. The funny thing was that it looks like it belongs there now.

The whole project cost me around $150 and took approximately 40 hours to complete.

Our first plan from Ana White. It was really easy to follow and this was a fun project to do with the children. We used pine wood because it was cheaper than cedar, so we will try to not put them directly under the rain.

We were able to make two birdhouses in removing .25 inch in one birdhouse. We used wood we already had for the third one.

We let the children added some details to the birdhouses. Because of the birds we want to attract here, one hole is 1.25 inch and the other two are 1.5 inch.

If you're looking for an easy built that will INSTANTLY add more seating for your outdoor space, look no further! This was such an easy build and is one of my favorites so far. All it took was 2X4 boards, which are dirt cheap. 

www.withlovefromgablog.blogspot.com

I combined the Reclaimed-Wood Headboard with the Hailey Platform Bed patterns, both found here on Ana's website to make my queen-sized bed. Alterations to the general instructions include: A 1x6 was sandwiched into the lower portion of the headboard to create the head of the bed platform (same as the panel pieces of the headboard). Another 1x6 was fastened from the back, the same as the other trim pieces. 4 holes for the light wires were chiseled out of the top trim, then a 2x6 was fastened across the top of the headboard to allow more room for the mounting of the lights. (these last 2 pieces flush to the back of the headboard instead of centered.) So the project was not too top-heavy I added a 2x6 center leg to the headboard. For even more stability I added a 4 x 4 leg to the center support of the bed portion. The lights are LED (Ikea) and the wires are fastened to the back of the headboard to keep them safe from pets, etc. The corners of the platform bed are held together with screwed-in knock-down hardware (Lee-Valley). Dis-assembly was important to me, so the bed could be moved from the garage to the house! I am not an experienced wood worker by any means, nor am I particularly fast. The plans I downloaded from this site were very detailed. The project was both fun and full-filling!

Built in cabinet based on the bar door cabinet project. Reclaimed bar wood used for the doors and trim. Custom made steel hardware. 

This was our first project.. it was a good one to start off with because it was pretty easy. Our bed is king size. Our boards weren't perfectly flat so we had to screw a few braces in the back with some scrap wood we had left over.

The only real change I made to Ana's plan was switching out the 2x6 board for 1x6. I still used 2x6 boards for my base, but went with the 1x6 for my decking boards, and top backing boards. My reasoning for this was to reduce weight. Other than that I increased the size of the base by adding another 2x6 on top (basically doubling up the base height). This made the sectional the perfect height, in my opinion. The plan Ana offered was pretty straight forward, and I love the size of the sectional itself. Very happy with how it turned out.
Cost Breakdown:
Lumber : $200
Screws: $20 (I used anti rust deck screws)
Stain: $35 (I used a semi-solid stain in a drift wood grey)
Cushions: approx $500 (when I started this project I had no idea cushions were so expensive)

Took 2.5 hrs to cut, fasten and sand, and approximately 24-48 hrs to paint, stain and poly.

This has been a very rewarding project. Now I have people comissioning work!

Thanks for the plans

This was the hubby's second project off this site. Our dining room has been empty for the past 6 months that we moved in to our first home, so it was only appropriate for him to build something for this very empty space.

We did end up modifying the plans a bit... making it smaller (instead of 8 ft, it's 6ft) since we didn't need a huge table with just the 2 of us and the pups living in our home.

First I built the 3 weatherly style sectional, then I added the two-seat bench with table in between to square off a seating area in our yard... Family and friends loved them for 4th of July and I really appreciate the plans!!! Thx Ana White ;)

Built a small table for the living room out of a reclaimed pallet. 

11 year old son made most of it. 4 year old daughter helped paint it. Such an easy project! Thank You!