Community Brag Posts

This is the first furniture building project that my husband and I have completed. It took us about 5 weekends to complete it- including finishing.

We started with the benches as recommended in some of the comments and ended up buying a pocket hole jig and redoing the tops of the benches before completing the table.

The stain is Minwax Red Chestnut and there are three coats of Minwax Fast Drying Polyurethane on it. We're so happy with it and can't wait to start the next project!

Built to go with my farm house table. It looks amazing.

I was inspired by Ana's Over the Toilet - Leaning Storage Ladder to create my own!  This build is about as easy as it can get!  Just 3 easy steps. More pictures and details can be found HERE.

Let's chat wood!

Lumber:

(2) 8' - 2x4

(1) 8' - 2x6

(1) 8' - 2x8

Step 1:

Drill pocket holes into ladder legs.

Step 2:

Attach shelves with 2" wood screws.

You will attach your smaller 2x6 shelf at 17" from the top of each ladder leg and your larger 2x8 shelf at 34" from the top of each ladder leg as well.

I plugged each hole with 3/4" pine wood plugs.

Step 3:

Sand and paint

Happy building!

Miranda

I built this hutch from Ana's book. I made a few modifications to the plans. The stained top and stained back planks are from reclaimed wood. If you build this hutch be sure to choose white knobs. I my opinion, its what makes those hutch pop. If anyone has any questions I would be happy to answer them. - Brad

Custom Kitchen Island with a butcher block top and reclaimed pallet wood on the sides and back. Sliding barndoors cover the lower cabinets and hammered black gate knobs finish out the upper drawer. 

Our daughter has a very small room. She also LOVES disney princesses. So I wanted to build her a princess castle bed.... but how do you fit a castle bed in a 9x11 bedroom?

There were some plans on Ana's site (good plans), and others on-line. But many of these plans had the bed on the TOP of the castle, and we were concerned with her trying to make her way down if she needed to in the middle of the night.

She also loves her Disney princess canopy bed that she has now... so if I could somehow build the castle around that bed, we'd be set. Which is exactly what we did.

I reviewed several pictures online, and then designed this bed with Sketchup (I LOVE that tool).

There is storage in the stairs, in the towers on the front down below, and in the back up on top. I also put rope lights inside around the ceiling over her bed for that 'Night light Princess glow."

There is also enough room on top for her bed if she wants to put it up there at some point in the future.

The idea for the decoration came from another poster who simply used the Vinyl Disney princess wall decals.

She loves it. Plus its big enough for daddy to read stories to her up in the loft at bedtime!

I've posted the plans on the sketchup warehouse... here is the link...

http://sketchup.google.com/3dwarehouse/details?mid=65f7fb029052c660cb6c…

If you can't find it with that search the sketchup warehouse for 'castle bed.'

As a beginner I found this very easy to build. I took my time to make sure everything was measured and cut just right. I substituted longer screws for the brackets. The ones that came with the brackets seemed a little short. There's a trick to getting the screws in the brackets. The angled bar swings back to make it easy to attach the screws. Very happy with the finished product.

I saw a picture of marble machine years ago and I finally got around to trying to make my own. I seriously had doubts about getting it working; so I didn’t want to invest money in nice wood. Therefore, besides the dowels, everything you see was made from a scrap 2×4.

As expected, it was a challenge to get mechanism worked out. I had to remake the cup and adjust the pivot point but I eventually got it working as shown in video.

Build Instructions: https://www.instructables.com/id/Wooden-Marble-Roller-Machine/

In Action: https://youtu.be/sel0w0gXGQk

My first pocket hole project! Adjusted plans to make table 50 inches long.

Project is still in progress but so far this has consisted of a firepit, 20x20 slab, 4 cypress columns, bistro lighting, 2 modern outdoor chairs, 1 modern outdoor bench, 4 matching tables, and a project screen.  To come: flower bed, projector storage stand with casters and hinged top, outdoor speakers, and possibly a green egg stand, and extending power to the back of the slab.

I built this table with the dimensions described in the original plans, but made a slight modification by using my Kreg Jig to add pocket holes for attaching the tabletop and seat boards from below rather than drilling down through the top. I'm never really happy with the way a finish comes out after using wood filler, plus not having to fill holes saves a step in the finishing process (which is the really arduous part of the job for me). I also like the sturdiness of the Kreg joints.
This was my first project using the Kreg Jig in an application that didn't have the location for the pocket holes specified, so for the first bench I followed right along with the plans and just detached the drill guide and clamped it to my project to drill the pocket holes as I went along. For the second bench I was familiar with where all the holes should be drilled, so I was able to quickly mark off the location and pre-drill all the pieces assembly line fashion. The second one practically flew together.
If you want to use this method, you will be drilling your pocket holes in the boards labeled "seat support" and "tabletop support" (there are 2 of each of these pieces for each bench/half table). You can mark the position of the tabletop boards on the tabletop supports and drill your pair of pocket holes to correspond roughly to the center of where each board will be (so 6 holes in each of the 2 pieces labeled tabletop support for each bench). Nearly the same process for the seat supports, but remember that the holes to attach the outermost seat board won't be centered because of the location of the front leg. I chose to add a couple of pocket holes through the front leg board as well for extra sturdiness in case it gets picked up by that outermost seat board when the bench/table is getting moved. I have included a picture of the pre-drilled pocket holes to help clarify the above directions.
The build itself can definitely be classified as a beginner project and easily manageable by one lady (although it would be really nice to have a buddy to help move the finished bench...I had to take the tabletop back off mine to move it from my "workshop" (carport) around to my patio). In terms of time, the build for both benches could easily be completed in an afternoon; I ranked it as a weekend project because of the finish. The tabletop and seat boards each have 4 coats of an exterior semigloss paint and I custom blended the colors so that each board gets progressively darker as you go down the bench. I was inspired by the ocean, with the water getting darker as you go deeper and deeper. As you can see from my photos, I rushed headlong into the first bench and put it together unfinished (I was more concerned about figuring out the placement of the pocket holes than the finish.) For the second one I pre-drilled my pocket holes, then put on 2 coats of base coat and 1 coat of color (on seat and tabletop boards) before assembly, saving only the finish coat on the colored boards and touchups on the white boards for after assembly. I definitely recommend the second method.
I worked on the project over a couple of weekends and evenings because of weather and time constraints, but under the right conditions it could be completed in a weekend or even maybe a long day (especially with a second painter and in good paint drying weather). I'm really happy with the final product and I've already been enjoying the comfy bench seat for reading.

As part of a redecorating project using reclaimed barn wood for our guest bedroom, we constructed this window frame to display some photos from one of our siblings of barns found in Iowa.

The dimensions are 44” X 33” with each photographic image being 11” x 16.5”.
Since the wood had so many bore holes, we used ¾” redwood under the visible fascia for added strength.

Cost - $75 / 4.5 hours to build.

http://ana-white.com/2009/12/plans-barnwood-frames-1-and-10-minutes.html

My daughter-in-law requested a pub table for my son’s birthday. Having never done this before I searched the web and found Ana White’s site (great by the way).  Table was built using the image of old_man’s table on Ana White’s site as inspiration (size 42” x 44” x 42” high).  I used 2x8s for the top, jointed and trimmed down to 6” wide and then glued together.  Since I could only clamp up to 25” wide, I made the top into two sections gluing one board at a time to minimize wet boards.  I then had two halves that I glued together using a wedge setup so as to avoid purchasing additional expensive clamps.  Once the top was complete, I sized out my base and opted to place the apron boards between the 4x4 leg instead of placing them outside the legs.  They were attached by drilling pocket holes in the apron and then attached with glue and screws.  The top was then attached to the legs and apron from using 1 1/2” right angle brackets.  As old_man stated and I concur, this table is HEAVY....  Thanks to both Ana White and old_man for the inspiration.