Community Brag Posts

I used pine wood and minwax walnut stain. I did run into a minor issue with a few of the slat boards being warped so I ended up screwing on (3) 1x3's onto the back, perpendicular to the slats, so the boards sat flat and their edges were flush. This also added more stability to the project. One coat of stain did the trick for the color we were going for. For such an easy project, this makes a big difference in the look and feel of our bedroom.

Since I am a very visual person when it comes to drawings and 2D/3D renderings, I have included pictures of the cut list shown on the boards you will need to use.  I hope this helps some people!  Keep in mind, if you use side mount drawer slides like I did, you need 3 extra 15.75" pieces for the slides to mount to.  I just used extra 1x3 boards I had hanging around.

We built this dresser plan to be used as a dresser / change table combo.  The guy at the home improvement store said to use oil based polyurethane so that it was more resistant to change table spills and traffic/wear over the years.  The oil based poly also added a nice amber color to the stained wood which I really liked.

This is the most complicated project I've made so far (because I've never made a plan with drawers), but after a couple tables and a desk from Ana's site (and referencing Shanty-2-chic also) I was confident that it would turn out well.

Change from the original plans --> We used 16in ball bearing "soft close" side-mount drawer slides instead of the euro style bottom corner mount ones mentioned in the plans. This requires adding the supports shaded in blue on the plans near step #7 pictures.  Getting the exact spacing width for those slides was a bit tricky and the drawer boxes had to be within 1/16" for them to work, so if you want simple you might want to stick to the euro style ones.  They allow for more "play" in the operation. 

Tip for attaching drawer faces:  For one thing, make the attahcment of the top and back of the dresser the LAST two steps you do on the whole project since it makes installing drawer slides and drawer faces a breeze.  That said, when it cam time for attached the front of the drawers I used 1/8" tile spacers all around the sides to make sure that gap was uniform and correct (see pic #4).  It was the simplest way I thought about of going about it.  Mounting the drawer boxes to the slides needed to be done before attaching the face boards for me.  And instead of nailing the faces on from the front and then screwing from behind; I put glue on the drawer box, put the face board in place using the tile spacers, and then added screws from the inside of the frame side.  It was a breeze. 

As the plans stated, I attached the top with PH screws through the side panels and six countersunk screws in the 2x2s along the width of the top using 2" screws.  It would have been a lot simpler to install the countersunk ones if I had a right angle drill or short handles screw driver, but I did not, so I made a normal one work.

If you have any more specific questions about my version of this project please let me know.  I was hoping to get to share more than 5 pictures, but that seems to be all the posts let you put up so I tried to included the most helpful ones.

got a kreg jig for mother's day and tried it out on that dead space in my broom closet.  I made $10 shelves, but in a "Z" shape instead of a "U" shape so I could attach from below and have more room on the shelf for cleaning supply storage.

 I used a 1x6 for the shelf and spray painted them black with some paint I already had.  So easy!  I used a 1x4 with a block of wood to hold up one end of the shelf so I could screw it into the cabinet.  Then leveled it and added second screw.  Awesome first project!  I learned a lot and got a place to put my spray bottles.

Sorry for the dark photo, my cabinets are black cherry.  

The cedar planters are ready and waiting for spring to arrive. I made three of these planters and absolutely love them. Thanks Ana for inspiring me to build. I love the third one but have to admit that it was a mistake. I made it for my father-in-law's 76th birthday. He loves gardening and shiny wood. So I used a polyurathane on it but it didn't look nice (my nail holes were very visible). So I sanded it with 220 grit sand paper and then used the steel wool/vinegar solution that I used on the first two. It turned out so different so I sanded again, then tried the solution again. I love it! It looks so old. I will be keeping that one and giving him one of the other two.

I needed a custom built printer table for the massive printer I just bought.  I figured if I was going to custom build it, I might as well add a couple storage areas.  Then I thought, I'm tired of having this VCR sitting on a TV tray to dub home movies to digital. So, I turned the top drawer area into a fold down face droor for easy access (and hiding) of the VCR.  Turned out great. 

I made this for my outside patio but since completing the project, it's been raining. So, it's inside the screen porch for the time being.

This was my first build- it went pretty smoothly. The most time consuming part was the finish since my time between coats took longer to dry due to the weather.

This is how we modified your plans. The project was built on the school campus then transported to the final site. We made this in frame sections and then assmbled with let in bracing to give ridgidness to the structure. We coverd with corrigated metalm and corrigated clear PVC glass. THe edges were covered with 2" x 2" dripedge. We will set it up on block and fill the middle with gravel to support water runoffand to give a solid walking surface. Our goal was to make a good quality movable greenhouse at the lowest cost possible.

Notes: If i was not concerned about cost, I would have used cedar 2x4 and would have used a heaviedr guage metal and glass. these two changes will raise the cost to around $1200.00

I've been needing a patio table for some time and this fit what I needed. Ready for next project!

I built this desk so my son would have a place for his old school tv and to do his homework! It was super easy and I love how the finish came out! His room is a huge work in progress but this is the first step:)

So easy! We need to hide a return vent on the wall and a faux fireplace was an excellent solve!

Plans make this a fairly easy project. Im looking forward to making a dresser to match as time allows. The bed ends up being a bit higher than i expected but still very happy with it. This made for a good 4 day father son build. 

I built 6 of these chairs to go with my Farmhouse Table I built. I did change them a bit. I changed the angle on the back legs and the seat. I posted some pictures of the process and went a little more into detail about my changes on my blog.

I mostly followed Ana's plans but used 1 5/8 screws and had a problem with wood splitting so for the ceder I used a finish nailer instread which worked great. I also painted before nailing the ceder pieces so they would really stand out and I also cut a few inches off the front ceder piece as I think 5.5in is too high and covers too much of the entrance. 

This is my first project working with wood. My husband and friends are very amazed by what I built.