Community Brag Posts

This has been a project all summer and I was so excited to find that Ana had made a mantle. I had to make it bigger and I had so much fun making it! Thank you Ana!!!

Update 8/2017: This project started with the Storage daybed, which I built in 2014. My daughter is a book lover and I wanted to provide her with more space for her books. I recently added the following plans to the Daybed with Storage Trundle Drawers:

- Twin Storage Headboard Base

- Small Hutch for Storage Headboard

- Cubby Hutch Plans for the Storage Headboard

I also made one extra storage headboard base and added more shelves along the long side of the bed so she could be surrounded by books. There are two additional supports under long bookshelf and I placed them roughly behind each of the trundle drawers.

For the bed (I built two), I opted to use the alternate slat system. I also used 2" caster wheels and added dividers to the drawers--one drawer has three compartments, and the other two drawers were divided in half.

Note: In my main brag photo it looks like the drawers don't close flush... I didn't notice when I took the photo because I was focused on the new shelves. But they do close and line up perfectly!

This was my next attempt after hte end tables. I used several ideas from different tables to get the finish i wanted. I also had to increase hte length and width slightly to suit my room. Had numerous complements from it and very happy with the finish

I was looking to add an element of luxury in my master bedroom so I built a fireplace wall with front opening mantle.

Christina Brooks

My son asked me to build him a narrow desk for his bedroom, with lots of drawers. This desk is a modified version of the Brookstone desk, with 7 drawers on the side and a pull-out writing surface (inspired by the pull out surface LadyGoats added to the Mod bar wine grid base – Gina’s pictures from her blog were really helpful!) The top measures 16 ¾ x 48 (top is a 1x12 and 1x6 edge joined with pocket holes). Lots of pocket holes on this one, because it’s stained and I didn’t want to fill nail holes. For the color we were trying to match the PB small printers desk Chestnut color. The pulls are antique bronze from Lowes. The drawers slide directly on the wood, because I knew I wouldn’t have the patience to install 8 sets of drawer slides ;) used ¾” S4S and 1x2 to hold the drawers. The drawer bottoms and the wood all got a coat of soft wax, and they slide nice and smooth. This took about 20 hours to build and finish over a long weekend. My son said he thought it looks amazing, which is the best part!

Built this for my cottage out of 3/4" birch purebond and pine. I finished by pickling the purebond and painting the pine and then used a laminate countertop.

I took these plans and changed the dimensions to match my dining room and made the cross members out of 4x4's. I wanted the bottom to be bigger, as well as making the top look like used yarn wood planks. Turned out great. It was wonderful to be able to have all the family around the table for Thanksgiving. Thanks Anna for the inspiration. 

Consoles tables made from reclaimed oak flooring 32 inches tall x 30 inches long and 7 inches wide.

Very easy and fun project.

This tower is from two or three plans found on Pinterest as well as the plans on Ana White.  The materials are from 2 x 2 or 1 x 5.  Length of legs are 34 inches, all cross members are 17 inches  basically your cutting list is :

Quantity         Size                             Description

4                      2 x 2 x 34                     Legs.  You can change this to taller or shorter.

14                    2 x 2 x 17                     Cross members

3                      1 x 6 x 17                     Safety sides

1                      1 x 6 x 16 7/8              Door (optional)

3                      1 x 6 x 16 7/8              Floor

2                      1 x 2 x 17                     Floor Braces

1 set                                                   Hinges (Optional)

1                                                          Latch (Optional)

1                      ¾ x ¼ x 3                     Door stop (Optional)

Distanced between parts-I used Ana Whites dimensions.

Basic unit.

1. Cut, sand, rout, sand, to size.Do not rout the floor as yet.Save that for later.
2. Drill Holes for fasteners on the cross members.I used the Kreg unit for this.Be careful as the 2½ screws can come out on the finished side (the point) if you tighten too much.
3. For the Safety sides, drill using the Kreg unit.
4. Finish sanding.I finished with 220 grit.
5. I stained before I assembled.Worked great.If you are going to spray paint, assemble and paint.See floor assembly now if you are going to paint.
6. Assemble is easy.Use glue if you want.Fasten 2 cross members to the legs at the top.You now have 4 legs and 2 cross members fastened but do not have cross members fastening all four legs together.They are two separate units.
7. Now measure for the cross members for the floor and attach.Install the top cross members first and work your way down.
8. If using the safety sides, attach these.Install the door if you want at this time.I waited unit I finished spraying the finish to install the door.Install the doorstop when you want.
9. Now attach the remaining cross members to form the basic unit.
10. Admire what you have accomplished.

Floor Assembly

1. I did not use the Kreg drill to assemble the floor.I used glue and 1 ¼ inch nails to assemble the floor.
2. Lay the floorboards on the cross member as if the unit was finished. Scribe a light line on the bottom of the floorboards next to the cross members the floor is sitting on.
3. Remove the floorboards and turn upside down.Put some glue between the boards and clamp.Lay the braces near the line you drew about 1/8 to ¼ inside the lines.This is important-you must have wiggle room for the floor to wiggle.
4. Fasten the braces to the floorboards.After the glue dries, check to see that it fits.
5. Sand, rout and sand the floor.
6. Stain the floor.

Final Finish

1.         I love rattle can finishes.  Deft is my favorite.  Use what you like.  Take your time.

My son and I build these shelving units as a side hustle. We’ve built dozens over the past few years, this was a solo build this AM as he was working at his day job.

Tip: use clamps to hold the pieces of wood together before which put in the vertical supports.

Nice little corner unit.

I made this for a friend whose son is turning 1. I wanted him to be able to sit in the seat without falling out, so at first I just planned on making arm rests (thus destroying the stack element, but he's an only child haha!). I had an extra piece of 1x8 laying around that turned out to be just long enough, and some hinges and a sash lock.

in the first picture, the desk is screwed on. I ended up changing it so he could use the desk longer! little legs can only squeeze into spaces for so long :)

Long story short, for this project I took all of the measurements for the original stackable chair and took 2" off to make it more appropriate for his size, EXCEPT the front legs, which I actually added 5 inches to. The front legs then stuck up from the seat about 5 inches, and i attached a 10.5" 1x2 from the front leg to the back leg on each side. Hinges on one side of the 1x8 board, sash lock on the other, and voila! desk-chair!! and it fit my 15 month old AND my almost 3 year old! granted, it was a tight squeeze for the 3 year old, but he LOVES the desk and I'm planning on finding a way to convert his stackable chair into one :)

Love these two projects in getting my son's room organized, and he loves having a desk for his lego creations and his "projects". We used poplar for the sawhorses that we had cut from family land and planed down ourselves, then purchased a premade project panel for the top. Used a paint sprayer for the blue and finished the top with Rustoleum stain in Wheat with several coats of Rustoleum Satin poly. For the toy shelf we just purchased pine and finished with the same stain and poly.

Loft bed made from the camp loft plans. I used 4x4s for the legs for extra support.

My husband and I made these for our grandchildren for their bedrooms at their new house. Same plan, just personalized each one.

We started with a play table from Ikea, added a 1X3 lip around that and then built a train table top to the same dimensions as Thomas the Train tables, trimmed it with 1X2 and glue thin felt on the base. I built cleats uner the top to fit snuggley over the base table. The train top can be lifted off and the under table is perfect as a leggo table when my grandson is old enough for leggo.

Months ago while browsing online I stumbled across a cool coke bottle opener. I had no idea what I would do with it but I knew I had to have it! So after months of procrastination I finally decided it was time to use it.

I found a cheap esky at kmart and decided that I would be able to make an esky stand and use the coke bottle opener on it. So after a trip to Bunnings for some new timber I got to work. It only took about a week to get it done including staining it.