Community Brag Posts

Built in a few hours and cleaned up seams with caulk.  Finished it off with standard trim paint.

Loved this project! Now I can really start building some other wood projects.

I decided to modify the one piece kitchen plans for just a stove and sink as I wanted something a bit smaller. I added a shelf (or rack!) to the oven and "tiled" the backsplash with scrapbook paper and Mod Podge. The burners are wooden plaques from Hobby Lobby that I painted with chalkboard paint and on the side outside of the kitchen (not pictured) is a chalkboard and towel rack. The Kreg Jig was incredibly nice to have for this project but I did add L-brackets to the outside shelves in case a lot of weight (i.e.. a 30 lb toddler) was placed on them.

I started building built-in bookshelves based loosely on the LACK copy-cat plans Ana posted.  I started getting to work on them and realized I needed a way to handle the 8' and 12' boards I have to cut down to make the parts.  Back to the home store I went!  This was an extremely easy project to put together.  I used one sheet of cabinet grade plywood ($30) and had it cut down at the store on their giant saw and three furring strips (as described in the plans, about $1.50 each).

My cuts were: 

1. In half lengthwise (now you have two 24"x96")
2. 24"x36" (on both halves from 1)
3. 24"x30" (on the long part remaining from both parts from 2)
4. You are left with two sections of 24"x29.75" (depending on the blade)

Assembly at home was really fast.  It took me 90 minutes, it would have been probably under an hour if I had the table already!  I didn't like the folding brackets at the store, so I went with fixed cheap ones for now.  I'll swap them later. You'll notice the saw sits a little lower than the side tables.  I'm going to mount the saw to the table and I'll fine tune with that.

Back to the bookshelves!

These planters were really easy to make, and held up well all through the spring and summer. This was my first garden, and I was excited to try raised planters. I added some reinforcement to the middle just to keep everything together, and they were really sturdy! Thanks Ana!

This is the rustic x coffee & end table I used 2x4's for the X. I like the wider look of the 2x4's over the 1x's it adds more dimension to the table. 

This is the first wood project I have made in years. Just got my wood shop built and this was the first project - thank you Ana. It ended up taking me way longer than expected. It was the first time I have ever used the Minwax custom color stain and quickly discovered after trying to stain one side why many say it is best for smaller projects. I quickly learned for a large project like this, it is best to do the boards before they are assembled.
It is pretty much the stock build, tho I did deviate some and added a couple of things. First, as i was doing this project by myself, I discovered that just flipping a wall over to add the trim is not as easy as it sounds. At that point in the build, the only thing holding the walls together is the bottom trim piece so it is very flimsy. To make it easier to flip over myself, plus maybe add some extra stability, I ran a 1x4 along the entire back wall about half way up. I believe it really helped with the stability and still can't be seen.
I also added 1x4's on the inside of the front walls from the edge by the 2x4 leg to the doorway - one above the windows and one below the windows, on each side. I just wanted to make it as stable as possible as I built it for my 3 year old grandson and I knew his 5 year old sister would be jumping around in there with him. It didn;t take any room away from the inside and really helped make it sturdy.
One other thing i sort of changed was the ladder. I do not know why as the trim piece was right at spec according to the plans, but the 38" ladder came up about 3 1/2" too short, so I ended up having to cut another one at 41 1/2". Also, especially as it was for a 3 year old, I thought it was a really big drop to the first rung when they were getting out of bed, so I added a 4th step. With 3, my grandson would have had to climb into the bed and when he was getting out, would have had to hang over and find the rung, this way he just walks right up. Keeping it at the 8" apart, the 4th step fit perfectly.
You can't really see the legs in the picture, but on the front legs, instead of using bolts going thru both legs, I put in threaded inserts on the front wall legs, that way you do not see any bolts on those legs. I also used the threaded inserts to mount the ladder.
It ended up costing a small fortune as I used #1 grade wood. I was originally going to stain it something along the lines of early american, but after spending hours trying to find decent wood at both of the big box lumber yards, even buying #1 grade I could not find enough good wood where the grain patterns were similar. I tried 4 various stains on some test pieces, was not happy with any of them, so then went with the Minwax Custom color charcoal gray, and I am glad I did. It has a bluish tint to it and looks just about right for a little boy.
Also, instead of adding the top trim piece to the back of the back wall, I put it on the front where it could be seen, plus it made it easier to hide the boards not lining up perfectly.
After it was all complete, I then applied 3 coats of brush on poly, sanding between each coat. I really wanted to finish it off by then wet sanding it and rubbing it out, but I did not think my grandson really wanted to wait any longer while I waited for the poly to cure, so instead I sanded it down one more time with 220 grit and then applied the wipe on poly.
In my opinion, it was Jaime from That's My Letter idea of the window frames that really sets it off. It looked kind of plain until I added the windows. For framing the windows, I just went ahead and sort of did it like a real window. The only difference was I was a little worried about my grandson maybe hitting his head on the window sill, so I turned them around and the window sill is on the outside. I didn't think it thru as i was thinking he could set some stuff on them, like his thomas train or something, but that obviously wouldn't work as everything would fall off when he opened the window.
For the red, I just used latex paint, apple red, then stained over it with the charcoal gray.
And then to finish it all off, the last thing I added was a 16' LED rope light. I just ran it along both sides and the entire front. I do need to put a switch on it so he can turn it on and off and not have to have his dad plug it in. I will just add it to the back of the wall where you can't see it, that way he can just flip the switch.
Biggest thing is I can't thank Ana (and jaime) enough. The grandkids love it. It isn't as nice as many would have done, but I am very happy with it and I forgot how much I like doing projects like this, tho this particular one took me a looooooooong time.
I still need to make him a sign and we are thinking about putting up a bell in the space in the top of the wall.

Very happy with the results.

First table!! I used all white pine that was milled over 45 years ago cut my own lumber out of this wood and the table top was made with 3 pieces of wood to make the top. Bench is being made now! 

This was my attempt at the 'Build an Entryway Bench...' project. It was also my first Ana White build.

A few notes:

- I had to modify the length of the bench in order to fit the 12 x 16 inch wire baskets I bought off eBay. Basically, I added 5.25" to all the horizontal pieces.
- I used a jigsaw to the the half-oval cut-outs on the bottom pieces. I got this idea from a similar bench from the Pottery Barn website.
- I routed the front edge of the seat with a round-over bit.
- I also routed the inner edge of the top with a core box bit.

It was amazing how quickly this went with the right tools and a couple mornings. Thanks for checking it out!

-Will

Liked the Griffen Reclaimed look Media console, but not the $1099 price tag that came with it!  LOL

So with $100 and 3 hours of work, BAM! 

70L x 15W x 30H

This was the first furniture my husband built. He also did amatching  sideboard table using Ana white plans.

This is our first project. I mentioned to my mother in law, we were one a mission to try an Ana White project while we were home over Thanksgiving. She surprised us with a kreg jig for Christmas! It is absolutely amazing!! I suggest it to anyone who is considering making this a hobby. Not on screw, is visible. THANKS SO MUCH ANA, WE CAN'T WAIT TO FILL OUR HOME WITH BEAUTIFUL FURNITURE!!

Quick and easy endtable made from scraps I had on hand.

Made from your Fancy X-desk plans. Dark Walnut & clear gloss polyacrylic Miniwax finishes.

This was my first wood working project. I am really starting to enjoy it.