Community Brag Posts

My husband and I built two of these endtables over the last two weekends. This was our first real furniture project, and we had a lot of fun working together. Thankyou so much for you plans Ana, it couldn't have been easier!

I used Ash wood from my local woodworking shop. The wood varied in width but is a true 2" thick. The table is 12' long and 4.5' wide. I didn't see the need in having the X on the leg ends as the ash was plenty strong enough to hold the top planks. Plus, I really like the look without it. I did add a cantilever beam in the center to stop sag. I didn't feel like I needed diagonal bracing in the center to support the cantilever beam (Note: Original design has center diagonal supports in wrong direction which do nothing for structural integrity of table). The table top planks were strong enough to span an 8' distance. The table top over hangs each end by 2' on center. I left the wood as rough cut as possible. I did rough it up a little more. I sanded with a #36 grit only to sand off writing, dirt, and burrs. I stained with MinWax Early American and sealed with Satin Poly by MinWax. Feel free to ask any questions. This is my 2nd wood project and I am hooked.

I saw this on Pinterest and immediately had to make it for my 2 year old daughter Autumn. It took only 1 weekend to do from start to finish. The instructions were very easy to follow. I did substitute 1 item though. I swapped out the 1x6 boards for the roof paneling and used cedar privacy fence pickets instead. The pickets were sitting outside at my local Home Depot and already had the great grey age to them. I simply cut them into 3 equal lengths and dog eared the ends to match.

Made with an ikea pallet and some other stuff.

After reading the comments, we decided to do the hinged learning tower, but took one dad's suggestion and used vertical legs on the non-ladder sides, too. We felt like it would be sturdier and would put less stress on the hinges. My son is much safer than he was on our step stool. He calls this tower his castle.

This is a small storage shed project I did to replace an old dilapidated plastic one that was falling apart and leaking. It was a fun on and off week long project.

Total cost of wood and material was around $200.00. All cuts can be done using a circular saw however I used a table and miter saw for simplicity and speed. The basic joinery for the frame is glued hardwood dowels (1/4" and 3/8") however you can use pocket screws or simply glue joints (screws for the 1x2 trim as they will move). All of the trim was hand cut using my pull saw because, well, it's just so much easier cutting 1X2's by hand than running back and forth to the miter saw each time.

A good rule of thumb, be prepared to use a weatherproof sealant on all cracks and openings that might let water in prior to finishing. For a finish I am just using two coats of outdoor primer and 2 coats of outdoor paint. I may end up brushing on a coat of water sealant (Thompson's) along the bottom half to prevent the skirt from soaking up any water.

Overall dimensions are approx. 7' tall X 3' wide X 22" deep with a total of four shelves and a small attic you can use for whatever you like.

The whole build is documented by pictures and text upon request, just send me an email if interested. Enjoy :)

This was a really fun project. I wasn't able to build it int time for the WWFC donation but suggest everyone do it this year (2016) around November. 

This is my 3rd build from Ana’s site. I built the dream Dollhouse with my daughter. She loves it! I would recommend taping off a section the size of the finished doll house to get a feel for the size. I knew it would be big, but wow it is huge. Fist thing she did was climb inside.
My 3 year old daughter helped when she could. She applied wood glue with a foam brush, painted the bottom and checked all the board walls and floors with a level.
I did not do the stairs, I did not think my daughter would play with them; I also wanted to keep the floor space. I still need to finish putting the wall paper up & add the casters. My dad got me 1 ½ trim for crown molding from the habitat for humanity store. He is also looking for caters there as well. Next time he come to visit are we are going to install it. With the crazy snow in Washington it might be a while.
I used a cheap primer that really mad the paint worse, but like my mom said I can always remodel it later.

I the supplies were close to $75, the new saw blade, Kreg Jig Jr., and other misc. to stock my shop a lot more.

Thank you Ana for such a great plan!
Becca

Theses cabinets were built for a customer from plans they had found online. The hardware was ordered with the plans for an extra expense and the glass was made to order. Hope you enjoy them thanks for looking.

I had a blast building this rustic x coffee table. Fun project

Super easy chair for the little people in your life.

I followed the plan exactly. The only thing different is that I added decorative trim.

I am a beginner and this was fairly easy. The only part I had trouble with is when I went to attach the back panel to the bench. It didn't quite line up. However, once I started screwing it down, it got better.

This (so far) is my best creation yet! I had previously made a bed for my son but my joinery skills were not up to par so it didn't make it. After re-evaluating his room I realized he was lacking on space so we needed to ditch the dresser. So glad I ran across this plan on Ana's website!

Since I was ditching the dresser in his room I needed to make sure the drawers were deep (25"x18"x10.5"). I once again ran into some issues where I was not paying full attention to the instructions and ordered side-sliding drawer slides instead of under mounting ones. So I had to alter the plan a tad bit. Not to mention my drawer openings were not completely square so I added some door trim and beadboard to the face and let it cover the imperfection. I must say it was well played!

I didn't have all the tools needed right away so as I got to different parts of the project I bought so many tools!!!

Easy beginner project.