Community Brag Posts

I just had to build these for my two kids. Thanks Ana!

Play Teepee used 4 yds of fabrics, 2.5 yd of webbing, bias tape, ribbon, heat and bond double sided adhesive, and 4 1x2s at 8 ft.

I looked at all the sofas that people built and took bits out of a lot of them to decide what I needed to fit my needs. I am in a tiny house and I wanted the sofa to be super versatile as well as being good for storage. I decided to build it the size of a double bed, but to divide this into three sections so that it can be used as a sectional, a seating area for meals and a bed for overnight guests. It was a lot easier than I thought it would be.

Thank you for this, I would not have known where to begin.

I decided on brightly printed outdoor fabric because the interior of my tiny house is all wood and I though the bright colours would be a nice addition. The outdoor fabric was chosen so that it would resist water and stains as well as pet hair.

We made this table from the farmhouse table plan but used 4x4s for the legs and slightly wider (2x10) boards for the top.

So my wife found this on Pinterest last month and loved it. We have been searching for something to go behind our sectional couch in our den. When she showed it to me I discreetly emailed it to myself as a plan was forming in my head. She was working nights for the month of December so I worked on it in the garage in the evenings and hid it in the crawl space so she wouldn't see it. She woke up Christmas morning to find it in place with a bow (clearly made by a man who is much better at carpentry than bow making) attached and was very surprised and excited.

I distressed the wood using several highly complicated techniques such as hitting it with a hammer, dropping a bag of screws on it, and scratching it with a screwdriver. It was then sanded and stained with Minwax Provincial 211. I applied two coats of satin polyurethane for protection.

I liked the look of the hex head screws so after painting them flat black I actually used them to hold the top on.

2 - 2x12x8

2 - 2x3x8

2 - 4x4x8 (cedar, fur is cheaper and will work fine also)

16 - 5/16x4 lag screws 

16 - 5/16 washers

3x10 feet 1/4 hardware wire

20 - 3inch wood screws (outdoor rated, deck screws or the like) 

you will have left overs if you buy extra lags you can make some other boxes depending on how high you want these, or set them on ground without legs. and use the wood screws 

I had inquire on your Facebook about you making a new plan... i had wanted a side table to hide my propane tank. I used the planter plans as an inspiration for this table. It is regiment rough looking as I managed to build it using only scrap on hand. I did have one cedar board in my pile that was leftover from another project that I used for the top... pretty happy but know it would have been better with new wood that was the right size and not warped! The space at the top is on purpose to be able to teach in and turn the gas on and off.

My sister n law and her family were moving and sold a lot of their furniture, so I built these as a Christmas gift. They came out great and I think they really appreciated it!

We made this a double bed and lowered the height by 3 1/4 inches because we have low ceilings. We added an extra support under the mattress since it's a double. Plan to add the desk and low shelves later. Followed the plans very closely, worked out great. One thing I would suggest is to do the slats after the guardrail. Otherwise you can't stand under the bed and it's hard to get a good angle when screwing it on. Many happy hours of reading Harry Potter up there in the first week :).

Outdoor couch excellent plans, easy to make and result is amazing.

This was our first woodworking project. I was not that hard to put together.

I made a couple of changes to the design. I used 4x4 for the legs. I also change up the board that were used ontop. I have a step by step on my blog.

The almost the same as the table. Check out the changes and the cut list here: http://www.domesticated-engineer.com/1/post/2012/05/bench-for-farmhouse…

This is my first fully finished build. My very good friend was about to have her first child and I wanted to do something special for her so I embarked on this project. I had HD cut my wood to size. After I came home and started building I found that my wood was not exactly cut to size. One side was one quarter inch too short. I did some improvising and some trimming with my jig saw (only saw I had) and was able to eventually create a rectangle.

This is also my first mitered trim project. The edges are NOT perfect but what I could I filled in with wood filler. That helped hide where the edges did not quite meet.

I then sanded and sanded and sanded. Don't want little fingers to come into contact with bad splinters. I finished with a bright white paint.

I wanted the toy box to also be a seat so I got some fabric and did just that. I was going to add hinges to it but then thought again and decided not to. Wanted to prevent any accidents.

I built it over many months spending maybe 20 hours or so. Many many mistakes and many hours thinking about how to fix them.

I took a crib plan I saw on here from DIYstinctly Made, but I wanted to have a crescent moon, so I altered the plans to a solid back with a crescent moon in the center!

Such a fun build! Can't wait to start my new project 🤗

Jenuri