Community Brag Posts

Built 2. Stained one Briarsmoke the other to be determined. Thank you Ana for the inspiration and plans!

I took the Hailey Platform Bed plan and cut to a twin bed size. I used some old wood I found in the garage for the head and foot boards and the legs. Notice the legs are 4x4s. The grandkids had some old bed springs under their mattresses so I incorporated the spring into the build. That required that I lower the cleat a couple of inches and it meant I had a very complicated leg geometry in order to get it deep enough to support the bed. I built the frame with Kreg Jig pocket joints and they made the work very easy with such large and heavy timbers. Notice I attached the legs to the frame with 5/16" lag screws which allows easy removal of the legs if you need to make it easier to move. Came out very good but I think I will build the second bed without the springs and go for the slat method as shown in the plans.The result is beautiful. My neighbor commented that it looked very Pottery Barnish!

The second bed I finished yesterday is made with slats. A very smart move. The legs are so much easier to attach to the frame. Both beds are beautiful and sturdy. One grandkid told me that when the hurricane comes he is going to get under his bed because it is so strong. He may be right but I will be in Laredo or San Antonio.

I'm so excited, this is my first furniture project. My husband was a little hesitant initially but is happy with the completed bed. This bed is so sturdy, I can easily sit on the edge and even lay down with my daughter. She loves her new bed and her brothers are a bit jealous. I told them to go through Ana's site and find something they like! Thank you so much for the projects you offer on here.

I altered the plans for a 28" wide crib mattress. Instead of a 1 x 3 on the ends of the head and footboard, I used 1 x 4s all the way across.

I also altered it to be 3" taller because I need a little extra storage space under my daughter's bed.

I did not use a nailer, just a hammer and nails. I found that it helped to use legs and shims on the bed rails frame and get to perfect level and then nail the footboard to the frame. Next, I screwed the frame into the footboard. This might be unnecessary info, but as a beginner, this part gave me a bit of trouble.

I used Behr Premium in Ultra Pure White with an Eggshell finish.

We are developing a completely off-grid property and before starting on construction of the house, we decided to start with a smaller project to get our feet wet (no pun intended!). We also wanted a place to soak our sore muscles while we build a house since we are restricted to taking 60-second hot showers, and so we came up with the idea of a wood-fired cedar hot tub.

Buying a cedar hot tub retail can cost anywhere from $3,000 to $7,000, but we were curious to see what we could build our own for and it turns out, we spent $850. Since there were no existing plans on the internet that we cound find for such a project, we decided to document the entire process and make our own! We struggled a bit with the build, but on our blog we documented what worked to save other people time who want to build something similar. In our post here, you will find a 9-part video series on how we put the hot tub together. Enjoy!

Built from Ana's doll bed plan. Added a drawer to match my granddaughter's bed and painted it her favorite color.

This morning my dad decided to help my build the workbench I've been wanting since we moved to our new house. I would usually do it myself but being 37 weeks pregnant I wasn't wanting to get out there on my own and lift a bunch of 10 ft boards. So we got a bunch of 2x4s and some 2x6s and threw one together... it ended up being 10 ft long and around 28 inches wide and a good 36 inches tall. Now I have a nice place to put my new saw I got for Mother's Day

http://ana-white.com/2010/09/pb-kids-caroline-craft-table

 *** apologies for the missing baseboard in the photo- we are in the midst of a remodel ***

We wanted a high quality table so we researched the Parker Play Table ($1200) and the Carolina Craft Table- ($600). 

In the research i found the plans for the Carolina table on this site- and modified them a bit (we wanted the removable storage top). 

We painted the top with White board on one side and Chalkboard on the other. 

The table has 22" legs and they can be changed out with a second set of legs when our daughter gets taller.

There is plenty of storage for all the art supplies in the unit and a art paper dispenser on the end. 

The unit is made of poplar on the inside and the legs and facia are all red oak- a very dense and beautiful wood. 

All exterior screws are counter sunk and hidden under face grain wood plugs that are surface sanded.  i chose to do no finish as the wood grain is beautiful- although i may do a timber oil or tung oil at some point - 

the project took about 2 days total time- $150 in supplies (including paint) and the piece feels substantial..... like it will be used for my daughters children. 

you will want to have access to a table saw and some clamps, wood plugs and a countersink bit for your drill

I essentially used the same materials as posted on Ana's website, with the addition of modifiying the plans to fit to my needs. I used the same hinges, however got mine from home depot Canada for 3 bucks each! woot woot. The paint was a high gloss enamal with 4 coats on the top or so. The legs were bought from a local hair pin leg guy and the cabanit doors were something a lil more special. The doors were made from 3 really really really old fence boards, that were sanded down and stained with golden oak minwax then 2 layers of oil polyurathane. Since the boards were a little more fragine than i thought, i attached them together with an extremely thing pieace of birch plywood and screws on the back. I really loved this project and pleased that ana replicated it on her website. Thanks Ana!

My husband built this for my birthday. He adjusted the seat height so the storage bins would fit underneath. We also added the corbels under the shelf on top. I can't stop staring at it! Just love it! We had no place for coats etc by the front door of our apartment before!

I actually designed & built this table on my own but it is very similar to Ana’s Simple, Cheap, & Easy Console Table. When we moved from an apartment to a house our lil neurotic jack Russell terrier decided he wasn’t going to eat unless we were both in the same room as him. So his food was put in a spot where he could see both of us even if we were in separate rooms, it just turned out that where that spot was, is the exact spot I wanted a console table. Well I couldn’t find a console table with a raised dog bowl shelf in it so I built my own. Now the dog bowls are up off the floor at a comfortable level for our fur babies & I keep all their vet paperwork, sweaters & toy stash in the drawer, all puppies things in one place.

After moving from Hawaii to Maryland, I was finally able to make good on my promise to make a new bed for Suzie. I made very few minor modifications to the plans as posted.

I made these ledges with pine and white wood, 4' long. I wish I had used pocket hole screws to connect them, but instead I just counter-sank the screw holes and butt jointed the boards with wood screws. I filled the screw holes with 5/16" wood plugs and sanded them down flat. Then I sanded, stained, varnished, and sanded again.

Please see my process below on my blog.

Thanks, Ana!

First Project...Used pine for the base and oak for the top to match home counter top.

The bed is a mixutre of the loft bed plan and the farmhouse loft bed plan with some modifications of my own thrown in.  I liked the headboard look of the farmhouse loft bed and incorporated it into the plan.  I also made the side rails out of 1x10's to make it more beefy looking and I think it works better.  The supports for the mattress are made out of 3/4" bookshelves, cut down to fit as it added more support than 1/2's.  The desk is based off the loft bed desk plan, but I made the top piece out of 3/4" MDF. I think it makes a nicer look.  I added 1x2's to the face of the bookcases and desk top to finish it off and make everything look more finished.

I also added a programmable, remote controlled, RBG LED lighting system under the bed.  My daughter can go from dance party to mood lighting depending on the situation.  This bed will deliver.

I also modeled everything in 3D CAD using Solid Edge.  This was a very helpful tool to get all the measurements correct as well as incorporating 3 different deisigns blended with my own.