Community Brag Posts

It was a fun project over two weekends. Thanks to this platform. - Teji

Followed the plans for the sandbox for my granddaughter. She absolutely loves it and so do I since I have a seat I can sit at! I did enlarge it a little so added some supports. It works so great. - Sandy

My hubby is 6'5'' tall. Since most matresses are 80 inches long, he mostly ends up with his feet hanging out of the bed (since you don't lay your head down at the very beginning of the mattress, right?). So I tried to solve this problem by making the bed 4'' longer than the plans suggested. I added 2'' of foam on each end of the bed, so now its 84'' long and my hubby fits perfectly!

Thanks for the great plans, I had a blast building my own bed!

We recently moved from our small Minneapolis Bungalow to an apartment in Maryland. It was the prefect opportunity to build the Farmhouse Table plans I had been admiring. When we went to my parents farm in North Dakota for Thanksgiving we spent a couple hours digging through the barn to find old barn wood for the project. The wood then made the 1,400 mile trek to our new apartment in Rockville. Yes, you read that correctly…the table was built in our carpeted apartment! No excuses people…you can make this table in your apartment! If you do not have access to a saw your local big box home improvement store can make the cuts for you. If you go that route the cut list Ana has will come in very handy!

I do a fair amount of woodworking, so I was able to complete the project in one day. If this is your first project I would allow a weekend to finish it.

This is only the second project I've done, and I think it turned out great.  I modified the measurements so that it fits 3 on each side and 2 on each end, 10 total (but it can seat more; the table is huge).

All I have is a band saw and a drill, and that's all I needed!  The legs and support are Doug Fir from HD.  The top is all 2x10's that I bought at a lumber yard so that they would have it kiln-dried and have the edges re-sawn.  The only 2x10's I could find at the big box stores were green.

I finished it by sanding with 100 grit paper (I read not to over-sand doug fir for staining purposes), stained with one coat of Special Walnut (two coats on the breadboard ends), and 4 coats of satin poly.

This table is a tank.  So glad I assembled it indoors, as we would have had trouble getting it in the house after it was all put together!

Using the plans for the farmhouse table, I took them and modified a bit and this is what I have come up with...so far... many more projects to come!

I used elements of both the Emme Twin Bed and Farmhouse Storage Bed to create this perfect bed for my daughter. Thank you so much for your fantastic plans Ana!

This was a fun project that my Dad and I had the opportunity to work on together. We were able to locate an old barn that and recently been blown over (farmer gladly told us to take whatever we wanted). We salvaged the wood, hit it with a little sand paper that provided the true rustic farm house look. With some modifications and a biscuit joiner we were able to fit this together. All in all I think I spent a total of $6 on the lag blots for the legs. 

I made a couple of decorations from my scrap wood.   On the snowflake, I had some extra parts of 1x2s laying around so sized this down to 20" and used those.  The tree is just a bunch of different types of wood I had left over.  This was really fun to do. 

It took me a little over a day as I had to paint and wait for it to dry before I could assemble.

Thank you for the ideas and plans.

Looking for rustic outdoor table ideas, I came across Ana's website and the Providence Table and benches. When I saw it, I knew this was what we were after. After some more browsing I came across the 4x4 truss beam table and decided to rather go with the chunkier table. Although I’ve done a few woodwork projects, this was the most ambitious to date, especially considering that I only have a few hand held tools.

We live in beautiful Cape Town, South Africa - we work in metric, so all dimensions needed to be converted. Also, our locally available wood sizes are different to timber sizing in the States, i.e. we don't have 4x4 (100mm x 100mm) or 2x4 (50mm x 100mm) available, so it was a bit of a challenge to decide what to go for. In the end I decided to use 75mm x 50mm rough cut treated construction pine. It was cheaper, and I could end up with a REALLY Chunky table if I glued 4 pieces together! In order to do this, I need to amend the plans as if it was made from 6x4 beams.

So I started the process of cutting the 75mm x 50mm timber to rough sizes, gluing the pieces together, sanding the joints, filling the gaps with glue/ sawdust mixture and re- sanding for each member of the table! I took my time with this and did a bit each day after work. It was interesting watching YouTube vids on this build - the guy starts with perfect 4x4 timber pieces, cut them and assemble. For me just to get to the starting point took quite some effort, but I knew I would be very happy with the more chunky look.

Other challenges I did not fully appreciate when deciding on the REALLY Chunky size, was the cutting of these thick pieces of timber using hand held tools and how to join them!! You don’t get very long small drill bits for pilot holes, so ended up using self-drilling screws. Unfortunately the longest length I could find was 120mm (8.66inch) - so I had to counter sink them really deep into the timber - this was quite tricky!

Other things I did were to lower the original design table height as recommended by other builders on this site so I made the table height 750mm (29.5inch). It worked out very well for small children as well for adults (I'm 6ft2). Table length I made 2.4m (approx 8ft). For the table top I used 220mm x 50mm (8.66 x 2 inch) timber, once again due to the restrictions of locally available sizes. I also change the spacing between the legs in order to fit the benches under the table (1600mm opening to fit the 1550mm benches).

For the benches, I once again had to decide what timber sizing to use. I wasn't keen to go through the process of forming 6x4's for each bench member for 2 benches and also felt that it would look just too chunky for the short bench legs. So the design ended up being a hybrid between the providence bench- and the chunkier 4x4 bench design, using 2 pieces of 75mm x 50mm to create 100mm x 75mm (4 x 3.5inch) legs.

Other changes made to the bench design was to make the bench height 450mm (17.7inch), amend the overhangs of the seat, and change the overall length to be able to slide the bench in under the table.

The altered height of the table and benches really worked out well and we sit very comfortably at that table.

We used chalk paint for the finish, but as you can see, we're still deciding on colour choices and final look of the top.

As stated in my table post, I just wasn't happy with what I was finding in the stores as nothing seamed sturdy nor made out of solid material. So I built a pub table and these stools to match.

I combined the stools from multiple projects and eventually just made my own measurements and mimicked the table construction that I made.

Although more expensive, I used Oak so it is sturdy and will take more than normal wear and tear (as I have three young boys under 10)

Loved the twin sized cabin bed but my grandson is a few years away from needing a big boy bed.  Husband scaled down the plans and this  is what we came up with. 

This was my husband and I's first furniture building exercise. We've been looking at farm tables but the prices were astronomical ($500 to 1,000+)! So, we came across this plan and thought maybe we could do it. And we did!

It took us about a weekend...we have two kids - ages 3 and 6...so we have frequent interruptions...including my daughter spilling my brand new quart of paint...so another trip to Home Depot.

We made some alterations to the plans...to fit our needs.

List of Alterations:
- Moved apron back (and would move it back more if I built again) 1" further.
- Added another stretcher on the bottom so that we could put a shelf there. We will probably add wood to the shelf in the future. Another blogger used a free pallet that he took apart. Seems like a good idea. Also moved the stretchers toward the back so that stools can sit under the table and be out of the way. Our table (as seen in the pictures) is up against a wall...so it made sense.
- Didn't add breadboard - the look was too finished for us.
- Used 1", 2x6 pine boards for two reasons - 1) liked the thinner material. 2) needed a smaller table than then 2x8's would let me do.

Tools:
We did have to buy tools to accomplish this project. My husband has a lot but obviously not enough.
- Purchased a table top miter saw - Harbor Freight - $89 on sale. Our circular saw just wasn't powerful enough (battery operated) and too hard to use.
- Purchased the full Kreg Jit (because it has the clamp mechanism) - $99

Thanks for looking!

Built from the storage bed collection as one of my sons Christmas presents. He loved it so much he cried. This is the first project that I have built and I think that it went rather well. I can honestly say I am now hooked.
 

Hello everyone

Just wanted to thank everyone for there great cabin beds and anna white for the amazing plans. My husband and I found them super easy to follow and create. I highly reccomend some stairs our little guy is still only 20 months hes a little short getting in and out... currently the step stools working great.

We had a blast making it ! 

I built this Kid's Country Bench for my son's play corner in my living room. It was so easy! The hardest part about it was waiting for the finish to dry lol. My 3 year old was able to help with a few things and he absolutely loves it! Thank you so much Ana!