Community Brag Posts

I followed the plans to the dining table with the suggested 1/4" spacing and extra slat so that this table will match the bench I will be making next.  I used the kreg jig for everything so that there are no visible screws.  This table is relatively simple to assemble and seems sturdy yet not too heavy.

I followed Ana's plans http://ana-white.com/2012/06/plans/fancy-x-farmhouse-table Total cost for me was $150 thats lumber,screws and stain. Total time for me was approx 6 hours and it was most time consuming for the legs. I build this in my yard as I don't have a shop. I put my old table saw on a pallet and my chop saw on the table saw. I altered a couple pieces to make the look different and bulkier for me. This is going to make an excellent gift. I just need to put a finish on it and seal it. Oh and I made mine from spruce. *Update* So we finally were able to put a finish on it with a 24 hour window of no rain. We used 2 coats Behr Cedar stain. It is an all in 1 and turned out beautiful.

*Note*

Not pictured, but I did add a strip of wood under each end to pull the board ends flush with one another. I used 2 1x2's with ends cut at 45 degrees. Length was cut to fit. This isn't something that was in the build plans, but it was very hot out when I was building this and the boards were starting to run up and down if you can see that in the photos.

I went this up this afternoon after seeing the plans. It's only 3 feet long because I only had one board that was salvaged from a friends garage. I could not bring myself to use another piece of lumber I went this up this afternoon after seeing the plans. It's only 3 feet long because I only had one board that was salvaged from a friends garage. I could not bring myself to use another piece of lumber different

I love this storage bench!  I modified the cut sizes to make it a coffee table also.  I made it shorter and thinner.  Now I can put my feet up on it, put a drink on it, and store some toys or garden tools in it!  You can check out modifications by clicking here.  Thank you Ana for the great plans!

A good friend of mine, a pastor of a local church, asked me to build a pulpit for their recently finished church up in the countryside of Grenada. She showed me a picture of what she had in mind and based on that, I drew my own plan in SketchUp, and then built it out of Yellow Pine boards and Plywood.

Note to the dimensions:
After I drew the plan, and just when I was at the lumberyard to have the plywood and boards cut, I thought I might have had it estimated not wide enough, so I decided on the spot to make it 2" wider and the top panel 2" wider and deeper too. So if you'd like to build based on my plans, please consider if it's wide enough for your purposes.

This is what I used (corrected measurements here):

2x 2x8 26" long YP Boards (Base)
1x 18 1/2" x 6 1/2" Plywood (Base Support Panel)
1x 26" x 16" Plywood (Top)
1x 18 1/2" x 9" Plywood (Shelf Panel)
2x 45" x 9 1/2" Plywood (Side Panels ) - these are cut angled, see plans
1x 44 1/2" Wood Moulding (for the "stopper" on the top panel, and the "back" of the top shelf.

Built this table to have plenty of room for all the kids and a few family members for holidays

This plan from Ana's site fit the bill perfectly for the vanity in our guest bathroom. Only a short four years after building our home, our guest bath finally has a functioning sink vanity! We also added a Kraus brand faucet and vessel sink, as well as tiling the back wall and installing faux board and batten. The estimated cost is for the entire bathroom project.

Rustic Sideboard Project.

We had so much fun doing this! Took about 3 weeks with significant effort.

We only made it with the center drawer. The cabinets were enlarged on the outside to account for this.

We didn't tack the backing on. We routed in 1/4 inch in the back to inset the entire back. Very simple and easy.

The finish was fantastic. We did the following (Sanding heavily between each step):
-Minwax Provincial Stain
-Miss Mustard Seed Luckets Green (1 coat)
-Minwax Furniture wax.

We used the same hardware as on the website. Lowe's and Home Depot don't care a lot of inset hinges and I was concerned about ordering on line.

The plans were great and the project came out fantastic. Thanks for the plans and guidance!

Thank You Ana White for posting the plans to make this great project! Mine is a little different without the "X" on the sides....maybe mine should be rustic ( / ) consule....

The closet had a divider when I moved in. I removed that. It opened up the room nicely. I modified the master bedroom closet plans just a bit to fit my needs and space. The closet divider had to first be removed which opened up the room nicely.
It is roughly 94 inches wide, 18 deep, and approximately 84 inches tall.

I used Soft-Close drawer slides. I also installed motion lights under the top to both add a touch of something special and simply because it was kind of dark with the floor being black wood and the closet system stained black. I sanded it to 400 grit smooth by hand. It soaked up over 4 coats of minwax polyshades ( black) applied with a brush and then rubbed smooth with a soft cloth.

Wine hutch with added trim to give a finished look.

We have a limited amount of counter space in our kitchen, while also having a large open space that is unused. We've always planned on including an island once we renovate, but we didn't want to wait. We decided to build a butcher block-style island with open shelving underneath - a simple design that would give us all the counter space we needed and some additional storage space.

We bought a premade bamboo tabletop, as well as 4x4 cedar posts for the legs, 2x4s for the framework, and 1x2 slats for the shelf.

You can see all of the details of how we built it in the blog post, but here are a few of the features:

- an interior framework that connects to the tabletop and outer framework so that no screws are visible on the outside

- countersunk GRK structural screws used to attach the legs htat look like carriage bolts

-feet are angle cut so that floor is less likely to be scratched if the island is moved

We're really proud of this build and are enjoying having so much extra counter space. It's amazing what you can get done in a weekend!