Community Brag Posts

Decided to build a vertical herb garden after seeing a brag post. I used 3 six foot cedar fence pickets cut to 22 inches to fit between our garage doors. I used 2 inch nails and wood glue to keep everything together.

The best part was ripping th left over pieces of cedar at a 45 degree angle to use as hangers. I have not seen this described yet on this site yet. After you rip the boards you attach the one side to the back of the box so that the short side is flush. The other portion you attach to the wall so that the pieces will slide together to form a full board again. Its a great way to get the boxes flush against the wall and avoid expensive hanging accessories. It also allows you to do all your gardeining at your potting bench and then hang them when you are done.

This was a fun, easy project. The main modification I made was to use 1 x 6 boards for the bench tops.

I also used my Kreg Jig extensively for this project. There are no visible screws on the tabletop or bench tops.

My grandson Oliver couldn't wait for me to put a finish on it. He had to try it out while snacking on his great-grandmother's pumpkin bread.

My take on the Rustic X Coffee Table

Hello Ana

Just a quick e mail to say how pleased I am with your chair plans , I did add a few extras hope you don't mind.

I chose to go with regular plywood, and I used thin pieces of wood to cover the screw holes in the corners. I just rounded the edges of the corner pieces to make them meet up with the molding better. Then I routered the top to smooth it out. I stained and clear coated it instead of painting it. For the lettering I chose to router it out instead of drawing it on.

I have a small mud room and this bench was perfect for keeping shoes organized on the bottom shelf, as well as storing hats and gloves inside. The storage area isn't very deep but it holds a decent number of hats and gloves.

Fancy table for outside barbecues. I built this table out of 100% Cedar. In order to maintain the lighter cedar color, I just several coats polyurethane for outdoor protection.

I had a bunch of extra wood sitting around the garage, so I decided to build this. Reclaimed wood 41 1/2 long by 17 1/2 wide and 19 inches tall. I used natural stain so it could keep it's beat up charm.

My first project!

Our very first DIY furniture piece my husband & I made. We absolutely love it & will definitely be doing more DIY projects together.

I built these planter boxes to hold my raspberry and blueberry plants. Also by connecting them with 2x2s, it keeps my dogs out of the garden

We don't have a ton of space in our back yard thats in direct sunlight. Also we have an ugly old chain-link fence. I saw a lot of vertical gardens and decided that would help two issues, maximize sun space and obscure part of that ugly fence. It's super easy to put together and was pretty cheap as well. I took some inspiration from the cedar raised beds on the site and built all the planter boxes out of cedar fence pickets. I added some extra supports so that the weight of the boxes wouldn't rip down the planters.

I'm so excited. I have my very own work bench! Thank you Ana for the sturdy work bench plans. I've added drawers and some curtains to keep the dust out. My brother did most of the work on this but I did some of the build at the end and all of the painting. Even though this will be stored in the garage, I wanted it to look like a piece of furniture found inside the house. I love the distressed look and I think I've succeeded in making it look old. I've made a few of your projects which I will post later. Right now I'm enjoying my new (old looking) work bench and I think it's really cool that it looks like it belongs to a girl.

I learned from other project fails to sand down the boards as I go. So my hubby cut the lumber and handed each board to me and I sanded down the boards with 120 grit sand paper followed by a finishing sanding block. Luckily the lumber that we purchased was not super rough so I hand sanded everything down. Once each board was mostly sanded down we put it all together.

Since my hubby countersunk the screws I applied standard wood filler and sanded it once it was dry (about 2 hrs later). I then applied wood conditioner and about 30 minutes later, followed by 1 coat of stain and 1 coat of polyurethane finish. Once the polyurethane was dry I sanded it down one more time with the fine sanding block so it was perfectly smooth.

I must confess: this was the second time I built a coffee table from this plan. The first time I built it I did a HORRIBLE job with the sanding & staining. When my husband and I first built from this plan it took us about 8 hours to build it. The second time it took us 3 hours.

New Deck Chair

My daughter's school needed a personalized item, (a class gift) to be auctioned off at the annual Spring Gala. The project needed to be personalized by the children in the class. I used the plans from Ana's toy box project plan, changed the footer to bun feet, and added a lid. The lid is also an upholstered top that can be used as a bench. I used two slow close hinges, one on the left one on the right, then two regular hinges to hold the lid on. We sent in blank tiles for each of the children (4 year olds) to paint in class. They turned out pretty abstract but cute. The tiles on the front are supposed to be bee's, the school's mascot. It turned out great! Having a hard time uploading other pics of it, specifically how I did the lid inside and attached it to the box.

I built this piece from ana white's plans. I modified the shelf design and also the dimensions to meet my needs. Instead of using 2x6 douglas fir for the top, I built the top out of hard maple. The top is built by ripping down several strips of hard maple 1.75 inches wide, turn the strips on there edge and gluing all the strip together. This is what is known as a edge grain cutting board. I finished the top with mineral oil and bees wax. The top is food safe and knife friendly. If you have any questions please don't hesitate to ask. - Brad