Community Brag Posts

I combined the loft bed and the storage daybed to make this bunk bed. I also modified the plans slightly so that the posts extended to the ceiling and added stairs instead of a ladder.

Added rolling casters to the plan. Also decided to go with one big drawer instead of two small ones. The top is made from pine 1x2's that I glued togeter and then sanded dow. Do yourself a favor and go through the plans and sketch out your own plan and wood requirements ahead of time. There are a few mistakes in the plan when it comes to your buy list.

I made this easy and cheap Christmas tree wall shelf to add character to my guest bathroom.  I went through all my wood stash and found enough wood to build this project with! 

Make sure to pay attention to the long and short point directions in Ana's plans.  Since I was hanging this above my toilet, I didn't need the hooks so I just omitted the bottom piece all together.

I ended up using wood glue and a nail gun to put everything together so it went really quickly. 

I painted the whole tree with green chalk paint and distressed the edges with sandpaper.  Hung it up with L brackets in a stud.

Fun and easy project!  Thank you Ana!!

I saw this and fell in love! I've made three so far!

Thanks for the shed plans, I've been looking all over for something like this. I used 3/8" ply wood for the back wall to save money but spent what was saved and more on the shingles and stain/seal. I made the shed exactly 6' wide and 4' deep to fit the 6 2'x2's patio slabs.
The entire project took about 2 weeks to complete and cost about $700. We pay more in Canada but at least I finally got the shed I wanted.

We always wanted a real barn beam in the house, we bought an old ash beam that we used to create a modern mantel.   After some research, I decided to save some money and mount it on a 2 x 4.  I've provided some instructions on my blog.

http://www.woodworkingfourdummies.com/blog/barn-beam-mantel-diy

Cheers,

Ian

This was built as a nightstand/charging cabinet.  I made it a little deeper for more stability. I also replace the 4-5 drilled holes with a corded electrical/usb outlet that allows you to both plug electri cords and usb cords for electronics (about $10 online). I added a center 1 X 2 and magnet closers on the doors. I used unfinished wainscot for the center of the doors.

The bed on the left is the one that I made. I used as much reclaimed wood as possible for this project. I had a bookcase that wasn't stable that had a lot of 1 x 4s so I took it apart and used them. In the second picture, I made the elephant wall art with some 1 x 2s and stapled the fabric to it. It hangs on the opposite wall. It was a fun project. (did not make the bench) I have a lot of interruptions when I build, so I am not sure about the length of time.

My first Ana white project!
It was easy and I really tried to take my time to make it look nice. Great new BIG table for my sewing room! LOVE IT!!

Stained the top 2x12's black and the legs are oops paint that are a teal color.

I enjoyed making this project! My wife loves the table and benches.

A few months back a friend of my Sister asked if I would build a bed for her 10 year old daughter. I was excited to do it! So I finished up the projects I had already started and then went to work. I had never built bookshelves before. I wanted it clean and "hole-less" on the outside, so we found a Kreg Jig and I started learning. SUPER easy!! I believe it has been painted white. I can't wait to go see it!!
I followed Ana's plans except I used 2*2s for slats and used 16" wide boards for one of the bookshelves and the desk top. I want them to be able to use this for years to come and not out-grow it too quickly.

Thank you for the plans for this fence! So many sites tell you what you need to do to plan for a fence, but don't give you any dimensions, materials, etc.

I didn't do it exactly like your instructions, but close enough to give you all the credit!! I am a 45 year old woman, with only a little do-it-yourself experience. I went to the hardware store, and asked "what are these PH screws?" and felt a little stupid. But my friend Tanya and I built this fence this weekend, with a post level, stakes and string, a chop saw, two 18v drills,a sledgehammer, a string level and a sharpie! We are so proud of ourselves.

I still need to trim off the tops of the posts, and do a few little tweaks. Also, we did not dig post holes. We used oz-posts, and pounded them in with a sledgehammer, attached the wooden posts into the oz-posts with heavy-duty construction adhesive and 8 screws, and straightened them with a huge wood clamp. And next weekend, I'll be putting in raised flower beds along the bottom to cover the lower space. :-))

We have a very big dining room in which we tought none of the store-bought tables would look good in. We needed a square table!

We got inpired by this beautiful post on Ana White (http://ana-white.com/2011/05/farmhouse-tablesquared) and soon after that starting to go look for what sizes of wood we can get. We live in an apartment, with no access to super big machinery so we needed to work with what wood stores offered us. We adapted the plan to our desire. Total cost was lower that 300 Euros, including screws, glue and stain. We are THRILLED!! :)

Turned leg coffee table from pine.  I also built matching end tables (shown in another post).  :)

Built this bench over a couple of nights. It was really easy. The most difficult part was deciding on the color and finish. Overall it came out great and looks good by our front door. The finish is Old Fashion Milk Paint in Salem Red. I painted two coats and then sanded the sides and corners. I'm contemplating adding an antiquing glaze to give it an older look.

I utilized a mix of the platform sectional and the simple modern sectional to create this piece. I added the design on the back rather than the simple 1x4. I also made the entire piece out of 2x4s and 2x2s.