Community Brag Posts

This was a fun project for my husband and I! My 4 year old absolutely loves her bed. We have plans to add a curtain to the bottom to let her open and close it for her reading nook (or as curtains for her "stage")! :) 

I am very happy to have completed the up portion of the bunk bed. The full size down was done quite sometime ago and I became sidetracked on other projects.
This is a sturdy bed and a favorite in my home. One day I even found my husband napping (hiding) on the top bunk.
The part that I like the best is when we graduate from bunk beds we still have two beds to use.
I also completed the ladder and it works, but I cut it just alittle shorter than the plan called for. Lets just put another on my to do list.

Started with a reclaimed old barn door and framed it with Ambrosia Maple, see atop the base of the Fancy X Farmhouse Table base.

Full size bed frame.  Made from 4 by 4 posts.  ! by 4 and 1 by 6 boards for footboard and headboard.

Side rails from 1 by 8.

This cabinet was inspired by an Ana White project. My wife wanted more storage in our new home, and we had a sofa table at this location. But it was just a top, no shelves. I custom fit it to be flush with the window sills at the top and ends so it takes on a bit of a built in appearance. The top and bottom are oak faced plywood, all edges covered with iron on oak facing. As I was short of the expensive plywood, the ends, shelves and kick are doug fir plywood with a light oak stain; while not a perfect match gave a pleasing result that guests have not caught. The doors are 1/2" MDF, with a 2" solid oak end glued on where I routed the slots to open them. Slots are 1/4" +, 3/8" apart, and the top and bottoms of the doors routed to leave a 1/4" rail. The bottoms of the bottom slide slots have a slick poly tape in them, which really helps the doors to slide easily.

Sides and interior are brush finished with 3 coats of semi-gloss polyurethane, while the top has 5 coats. The MDF on the doors has one sprayed coat of white primer (oil based to avoid bringing up the MDF) with a final sprayed coat of mat finish enamel. I need to do one more step, light sand with 320 grit and paste wax the top to get that really fine finish.

While not as easy as Ana makes it look, it turned out pretty well. That hard part on a piece this size is getting all the pieces cut precisely, and I mean with less than 1/32nd difference, to provide a good fit. As it was I had to custom cut the oak opening ends on the doors to account for the small differences in widths at the top and bottom to obtain a nice fit against the sides. Next time I'll triple check all finish dimensions to make those small adjustments in parts before assembly, then triple check again for placement during assembly.

While I'll always see the small "errors", my wife is very pleased with the finished cabinet.

I actually used Ana's "Grace's kitchen" plans and modified them to make a single unit kitchen that was smaller to fit my space, after I was done this new project plan was posted! My kids love this kitchen and I love it's smaller size. I used all plywood scraps to make it, so the cost was minimal.

First project for me. Easy to do even with limited tools. Now I realize I need more tools to do bigger and better. It was a nice stress relief to go to garage and build something. My wife wanted something so it made sense to do this.

Built this

 Ana, you're the BEST!! Thank you so much for sharing these plans. This was a very simple build ... my problem was trying to decide how to paint and decorate it. There's a lady in our little town that cut out the letters for me. I think it turned out so cute. I'm working on a Christmas collection for our church auction next April and thought it would be fun to have Christmas in April :-). Thanks again Ana!!!

I modified the Salsa console table plans a little for my version. Assembly is pretty much the same, just added more detail like making 5 piece doors and draw fronts, adding back brackets to allow for cedar paneling behind the doors and recessed the middle walls so the doors close on them instead of inside the opening. The center will remain open for now.

the whole table and parts are poplar, minus the drawer bottoms which are beech ply. Because its made out of poplar, it jacked the price quite a bit. However, i wouldn't consider using anything less then select pine to make this table which is only slightly less that poplar. The #2 pine is total crap and not suitable to build a piece of furniture out of. Anyway, I've got about $300-$350 in building supplies (wood, screws/plugs, finish), and about $80 in hardware (hidden euro hinges and bearing drawer slides).

Hope you like it, as i am quite proud of it!

One other thing, if you plan on building this table, double check the material & cut lists. I found discrepancies.

My husband and I built this for our son for Christmas. We had so much fun doing this and all the detail that went into it. Both the fridge and stove have battery operated motion sensor lights & the backsplash is diamond plating. Very cool!

took me prob 6 hours to build 2 hours to oxidize 1 hour to oil.  No bolts are brackets yet, I really love it without! This was my first piece of furniture and first time oxidizing & oiling!

Flower potting bench for the front porch.

I needed something to fill an empty wall in my kitchen. I wanted something for both baking and wine storage so I modified a couple of things I saw on this website. Wine storage on the very bottom (the slats are wide enough apart that the wine bottles sit in the cracks and stay snug) with baking stuff above that. I think I'll build a matching shelf or two for the wall above it

I built this stool for my 2 yr old grandson. Added yardsticks to the top of the steps for a different look, and painted the stool, then sanded randomly, added stain and wiped off for an aged look.

Quick build for the garden swing.