Community Brag Posts

My wife and I loved the look of this plan, so I decided to make it happen! I built this same console, only half the length for our dining room, and then made this full size version for the living room area. I used this plan for both designs. I used a table saw to cut dado channels from the intersecting pieces of material for the "X" design on each side of the table which was considerably easier for me. It can get a little tight when trying to secure the 11.25 inch pieces of 2x4 and 2x2 with pocket holes so I opted to secure through the outer frame with 2.5 inch screws. Countersinks, wood filler, and some sanding made for a clean alternative to the pocket-hole approach. Stained and chalk painted frame and shelves separately before assembling. We love this table and promise you will not be disappointed either.

I didn't get the plans from this site, but figured I'd post a brag anyway. The plans were downloaded from MinWax several years ago , but it wasn't until this year that I started to build this roll top desk. It's made with white oak, along with maple plywood for the side panels. It was finished with a simple polyurethane clear coat.

I'll be using this as a work desk in my den. It has just enough room to house my laptop with the top closed.

This is definitely one of the more challenging projects I've taken on.

https://www.minwax.com/en/woodworking-project-inspiration/wood-furnitur…

Wanted a nice big table, but couldn't find one in local stores. Decided to build one after seeing a small tiled table at Home Depot. This is my first project like this. I am a network engineer not a carpenter, but the table turned out great.

I made it wider than the plan and use it in my bathroom for storage. Its pine and cedar.

So I made this a couple weeks ago. I used 2x12 for the top and 4x4 for the feet and legs. This was my first project and it came out ok. The feet need some work. The plan called for feet to be angled but unless you have a band saw just cut the 45' for the feet. 

It's the 8ft Barn Door tv console plan I purchased a while back, I finally put it together. I added my favorite color of paint and side brackets, I used coat hanger knobs for door handles. I love it, I've never took on a job this big ever. I'm so impressed and very proud of myself because I did it all by myself. Thank you so much and I'm a 62 yr old lady.

I built this caddy to celebrate a 4th birthday party for a sweet little girl. I used pine scraps, painted it with some leftover pink paint, and then created some name artwork and a little logo with her initial. I made the art on my computer (in Adobe Illustrator) held up a piece of notebook paper to the screen and traced it with a pencil. Then I held it on my caddy and used a mechanical pencil with the lead down to press the indent into the wood. Filled that in with a silver paint pen and traced it with a fine tip black sharpie. Then filled each cubby with a large mason jar from Walmart (about 50 cents each) and filled them with art supplies. It turned out so cute! And it's a great way to use up some scraps.

This was my first building project, made possible by finding this wonderful website. The beds were made from the Classic Bunk Beds plan. Several months later I added a slide made out of melamine board and 2x3s - very sturdy and somewhat overbuilt to compensate for not using any plans for the slide).

I used Minwax polyshades for the finish - my first time finishing wood, and let's just charitably say that I learned a few lessons in doing so.

The steps are a repurposed solid pine Ikea Trofast unit - it worked very well for the kids (4 and 2 when the bed was built). However, it wasn't a great choice for getting my wife and I up to the top bunk - one of the top panels eventually broke... leading to a big bruise for my wife and strict instructions that I quickly build a new, more solid staircase option - to be shown in a future brag post.

All in all, I am very thankful for this website and its plentiful plans - more brag posts to come!

I loved building my Coffee Table, thank you Ana White! I built mine to be 42" long and kept all the other dimensions the same, (but didn't do the X's). I also installed leveling feet. I stained it Minwax's Early American, and used 3 coats of Polyurethane and applied everything with a rag. I used 2" Corner Brackets, spray painted with Rustoleum Metallic Charcoal. I bought the baskets from Michaels.

Provence table knockoff from restoration hardware (aka: providence) with 4x4s and providence benches

table modified to 90 inch length, benches to 42 inches

used lag bolts with a washer on 4x4's that show, kreg pocket screws everywhere else

note: the free-diy plans listed last have an issue with the table height. It came out 1 1/2" too high, so we made a change that I like better: we modified the table top to have a 2x4 skirt held together with kreg pocket screws that drops over the 2x4 frame above legs. we left about 3/8" gap between the skirt and framing so the framing would fit in easily. The top actually just sits on the frame so it is possible to move it in two pieces. It is so heavy and stable that we didn't worry about screwing it together.

we love it! perfect for 2 families to eat dinner together. my husband calls it Thor's table because it looks so tough.

Plans use was the Bailey Console Table. 

This was build for the #igbuilderschallenge hosted by @desertwoodwrks and judged by @anawhitediy and @davidsheinkopf. 

I used two old queen sized bed frames for the legs and stretchers, welding them together with a Lincoln Weld Pak HD Flux core wire feed welder. With a little practice, anyone can do this easily! 

I used poplar hardwood instead of pine for durability. Stain is Minwax Jacobean, with 4 coats of Deft Clear Satin Spray Lacquer on top. 

Added a face frame around the doors, and made then inset flush mount drawers. The left drawer also has a false bottom, with hidden storage beneath the lift off tray. 

Recycled bed frames were used for the legs and stretchers (both front and back) and them painted with Rustoleum Black Satin Finish Spray Enamel,with the lacquer on top of that for protection. 

This challenge was so much fun to do, and it was a real blast seeing the creativity of everyone else involved! I can't wait for the next one. 

Follow me on Instagram : @amanteafinewoodworks 

I have a mountain cabin with limited storage. A friend gave me two cabinet doors so I built the box to go with them. I used 3/4 in birch plywood for the box and shelves which I made adjustable using metal shelf brackets.

This is a Double Pallirondack Settee, an Adirondack-styled set of chairs connected by a two-shelf table that is also an umbrella holder. It is made 100% from recycled wooden pallets (thus the name). It took approximately four full pallets to make the settee. The finished picture was taken by its new owners after they stained it with a cedar-colored sealer and added an umbrella.

The other two images show it before I had added the bottom shelf of the table and it finished before staining. I just finished a second settee and will be selling that to someone who saw the original one at a party.

The design is based on a couple different plans -- one for the chairs and one for the table/umbrella holder. I modified both plans to make them work together. Great fun. If I could have worked on it straight through, it probably would have taken 2 full days, starting with pallet deconstruction, then cutting pieces, sanding, assembly of chairs and, finally, assembly of the connecting table.

I made half of the Rustic X Console table. It was an easy build until it was time to make the X's. They were only hard because I was using a circular saw and carpenters square and I couldn't get my lengths right. I ended up with a lot of short pieces and I was glad I ended up buying more than enough 2x2's. If I had a miter saw it would of been a lot easier (I have one now).

I made this book case  for my daughter to replace an existing book case.  I the design is a little different from what I found.