Community Brag Posts

Made it a little taller and a little deeper.  

The husband kept complaining that the washer and dryer were too low without pedestals. Well, no problem! I've got plans from Ana's site.

I measured to fit our machines and followed the plans. But somewhere along the way I screwed up. I think it might have been how I attached the legs with the "L" brackets. My legs were sitting away from the base, not flush with it. Anyhow, the way to correct my mistake was to attach the moulding along the sides, front and back of the base, not around the legs. But I don't mind the way it looks. Just an FYI: there was a lot of waste with the sheets of MDF, but that's not a problem because I'm using it in another project as I write. :)

First, I put on two coats of primer. Then I decided I wanted a splash of turquoise in the basement, so I mixed a blue and yellow paint until I got the color I desired. After a few coats of paint, I distressed and then decided to tone down the color a bit with a Valspar glaze. I put on two coats of poly, hoping that would be enough to withstand the inevitable water on the pedestal. I thought the piece was screaming for a quote, so I painted "The most memorable days usually end with the dirtiest clothes."

And you think with the new height he'd help me with laundry a bit more? Yeah, I think not.

Our original sofa and loveseat turned out so well that my parents asked that we build them a set. It was our first time converting the plan to a single seat so I was nervous on how it would turn out, but it looks great!

This TV console was made on request.  Its made from maple plywood and Pine top, trimmed with Small crown,  large chair rail  and base board moulding.  It has one media shelf a larger shelf for Pictures. The very bottom has two 18 inch drawers that are 5 1/4 inches deep for dvds or games.

Followed the plan, adjusted the height to accomadate a trundle bed in the future. Tapered the edges of the 2x6 material for a shaker/craftsman look. If you cut the board at a 25 degree angle the 2x6 material will rest right in line with the 2 x 4 material below. Be sure and add 2 to 2 1/2 inches to accommodate the taper edging.

Used Minwax gunstock stain to match the furniture and three coats of fast drying gloss poly.

I worked on this over the past couple of months (would have been quicker, but you know..life gets crazy sometimes!!)

I used the farmhouse table plans to a tee and then stained and poly'd it. It turned out great!!! My Wife loves it and now all I have to do is build the benches. The wood is cut for them, just need to find the time to do it. This is my 4th Anna-White project. I have also built a bench for the end of our bed, some laundry cubbues, and a day bed.

I love this site and plan on using much more...I have friends and family wanting me to build them stuff...the only thing now...is how much do I charge..... :)

I built two of these bad boys!
I used the cheapest spruce wood as I knew I was going to paint them.
Not sure how much everything cost in the end - maybe €50. Am making 2 beds to go with them too but they'll be a little longer in the pipeline!
I cut the wood myself using my circular saw and joined the wood with pockethole screws.
I painted the tables white and then used a chestnut brown woodstain on the table tops, shelf and knob.
Hard to say how long it took me as I just did a bit every now and again when I had a bit of time.

My version of the rustic rolling kitchen island. Really can't do the x's yet. It's all leftover wood and counter top. I use my other one similar to this as a coffee station.

Building a workbench seems to be a rite of passage for most serious woodworkers. The Entry Level Workbench shown here is a collaboration between myself and Kevin at Kev's Woodworks. I've detailed the design while Kevin and his son built the workbench as a father/son project.

All details including dimensions, parts list, tool list, and a full cost breakdown are included in the link if you would like to build your own bench.

https://www.instructables.com/id/Entry-Level-Workbench/

Made by my husband.

Kitchen cabinet I made with raised panels.

Some more details at:
http://bendrea.wordpress.com/2013/09/22/kitchen-cabinet-2013/

My Second DIY project! It turned out PERFECT :) 

Finally, kitchen is done.  We've been in this house almost 4 years and for me the kitchen was not efficiently functional.  Dishwasher was on the wrong side of the sink, had a trashed compactor which we did not use, very little counter space, not enough drawers, etc.  

The whole kitchen was gutted except for the cabinet over the stove which I covered and still has storage.  

Thanks to Ana White for the plans and inspiration!  Learned a lot during this process.

I love my new table! My wood was a little bit warped for the tabletop, so that's where I ran into the most problems, but I used a hand planer to smooth it down and it turned out perfectly!

This was a really fun starter project for me. I've never made furniture before and I ran into some issues, but I learned a lot and enjoyed myself! My husband and I live with my Father-in-Law who has all the tools I needed (though I'm going to purchase my own later on).

The stool and table plans are here: http://ana-white.com/2009/11/plan-kids-large-storage-play-table.html . I modified it slightly because I was using scrap pieces (two doors from a particle board wardrobe). I don't like particle board... but I figured since it's my first try, I wouldn't waste any cash since I had all the stuff here, even the nails and screws.

So I made the table about 2 inches shorter and the stool 1 inch shorter. I also used a rectangle top for the table with one side flush against the table side so I could put the set against a wall (i.e. three sides have overhang, the 4th is equal with the legs).

I painted both sets a dark red orange (my husband's favorite color) and let my daughter put her handprints all over in white paint . She LOVES it. And despite the 'wood' I used was particle board, it's pretty strong. I'm pleased. I will probably make another one with stronger material in the future.

Oh there were a lot of holes and such from the used board and some breaks from being thin, crappy board, but I was able to use filler one a lot of it and glue too. It's hard to tell it was a beginner job from a few feet away! Haha!

Used 2x4s for the top instead of 2x6s. All the shelves are 1x2s. My first attempt at a door and drawer - it kicked my a**! 

Top stain: Minwax Golden Pecan

Then Minwax Polycrylic 3 coats