Community Brag Posts

We have a smaller house and wanted a dining table as well as a table behind our couch.  So, we got the best of both worlds with this minor customization.  I simply split the two legs and tabletop in half, added additional feet, and built two supporting braces instead of one.  For an added touch, I welded tubes to steel angle iron to make a hinge-style locking mechanism with steel pins.  This locks both halves together (when using as a full table) and adds a little rustic black metal to the overall look.

For the tabletop, I cut the sides off the lumber to get the square look.  I then bent one tooth in my tablesaw and quickly cut the face of the lumber to give it a rough sawn look.  I then belt sanded it all to smooth out the really rough spots.  Then I shou sugi ban (burned) the top to burn off the splinters and make the grain really pop.  I added a little stain to smooth out the light spots.  Lastly, I put about 64oz of epoxy and lightly sanded with 0000 steelwool after it set. 

Please excuse the floor trim or lack therof.  I just installed the new floor and decided our table was the higher priority.  :P

We built this activity/lego/art desk. We added a Lego base plate under one side of the table top and a paper roll to the side. We also built two little benches that fit right under the desk. These pull out and hold two kids on each side.

I looked high and low for something to store the plans at my office. Everything was outrageously expensive. Then I came across this plan and it is perfect. I did make some modifications though. Took 4-hours to build (not counting the wood cutting, I had that done at Home Depot). Then it took another 4-hours to stain it. Overall, I am really excited to give it to my boss when she gets back from vacation (it's a surprise).

I made this sink from a sink that I saw on here one time and can't find now. Just improvised didn't follow a plan. I have it in my garage and plan to stain it and add some touchs soon.

Thanks for the plan and the inspiration to do the job, it turned out great! Luckily, I didn't put the new bedding on yet, as the little ones needed some wrestling time.

Thanks!

This was my first build! I first stumbled upon plans for the cubby bench while Googling storage options =)

I combined plans from the Perfect Cubby Bench and Entryway Storage Shelf with Coat Hooks. I made slight changes to the dimensions; most of them were intentional. Both are only 36" which is perfect for my small space which doubles as the back-door entryway and laundry room. It manages the abundance of clutter created by a two kids and my husband.

I have shopped and shopped for the perfect entryway solution for this small space. Never have I found one until I came across the plans on this website.

Thank you, Ana! You've given me an excuse to start building...I had all the tools...just needed the motivation =) Now I have a ton of plans to get me started!

From a stay-at-home mom only one year into the job, I have discovered a new sense of personal enjoyment! The crafting, cooking, etc. is great and all, but this is my kinda thing!

This is our Texas Style Home Bar.

It is build out of 2x4s, 1x6s. The Base is 1,50m x 0,50m. The Top is 1,50m x 0,60m. It was build as a Tribute to the State of Texas where we lived the last 3.5 Years. The Base is made of 2x4s and some Edge Glued Boards. The Posts are also 2x4 and i routed a notch in there to fit the Boards. Problem was to rip the 45 Degree Boards so they fit the middel part. The Sides a Red with a White Stripe to look like a Barn Door. Top is made of Edge Glued Board. I made "Texas" Out of old License Plates and filled the Top with Epoxy Ressin Glaze Table Top. Was quite some work. I used Espresso Stain for the Dark Parts and White Wash for the other Parts. I also used China Red Stain for the Sides. The Dark and Red Parts are covert with shellack. All other with Polyurethane. The Top looks fantastc, and i had some old Beer Towels accomondate it. Most Problem where to made it with no plan. I sketched up what we wanted and start building from that. Difficult and Nerv wrecking. Had good help from my Family. I put casters to made it move better. The Glas Holder are made from T Molds. Bottle Holder are from scratch Material. Some decorate items are still missing but for now the Beer tastes Perfect from this Bar.

To be honest - this was my Second Big Project after the Farmhouse Table..

Thanks for commends!

Jann

Couldn’t wait to share this one. I’ll post the finished pics on here once the painting is finished and the cushion is sewed.

This build is a reclaimed wood version of Ana’s Simple White Outdoor Loveseat. We’ll be using this inside. This started as a way to repurpose those blue vinyl cushions (which I made 11 years ago for a hot tub bench – these had been stored in the garage for a few years). Using reclaimed wood on hand – reclaimed 2x4 studs, an oak 1x12 shelf and some pine 1x12 scrap ripped to 1x6 for the aprons, plywood from an old entertainment center ripped to 1x4 size, some 1x4 that used to be trim, a left-over 1x2 and S4S, and some left-over 1x6, constructed the frame and back. After I got that together, Hubby suggested we add some wide arms so it wouldn’t need to have a side table. That was the only wood I had to purchase on this one – a 1x6x6 for the arms, and a 2x4 for bracing the arms.

So far this has been a weekend project, including re-sizing the plan to fit my 24” x 24” x 4” cushions, doing the math to use 1x4 size instead of 1x3 size for slats and rails, and sizing to use the 2x4 frame on their ends rather than flat, to save a tiny bit of space in the footprint. Originally there were going to be 8 1x4 rails for the back, but I was 1 piece short, so instead of having 8 rails in 1x4, I have 6 1x4’s plus the 1x6 in the center (now I have 1 piece of the 1x4 left over). And it’s very comfortable for sitting!

Still left to do: sand the filled screw holes on the arms and paint the arms, and sew the cushion. I got that high density foam with a 60% off coupon at JoAnn Fabrics. Also the fabric was 30% off (right now it’s just draped around the cushion for the photo). The fabric and foam was only $90, and I’ll have enough fabric left over for a few accents. Hopefully I’ll get to that during the week, if not, on the weekend.

My daughter loves her new bed!  The plans were easy to follow and didn't take very long to build.  It took me about 2 weeks to finish.  I suggest measuring your mattress first and adjusting dimensions accordingly.  My daughter's mattress is a bit longer than usual, so I added about an inch to the length.  I added drawers to one side and left one side as open cubbies.  I also added a 2x4 base below the storage boxes for support.  Ana has plans for this in one of her kitchen cabinet plans.  I'm so glad I did, as I've already found 3 kids hiding on the cubby side, and one of them is 14!  I didn't run the 2x4 base all the way to the head/footboard, so it wouldn't show.  This changes the height where the storage boxes attach by 1/2 an inch.  The bed may suprise you at how high the mattress sits, but I think that is normal with a storage bed.  My daughter loves sleeping up high.  Thank you so much for this wonderful plan!  I love Ana's website and have learned so much!

This is my first project attempt from Ana's plans. I had to modify it greatly to fit my space accordingly. The room where it made its home only has a love seat and a recliner. The space also isn't that deep, so i made the table aprox 45" x 19" x 18" high. I also built a completely different top to this table as well. I felt this fit our personal style a little bit better. So being that this was my first project, it was a little more challenging due to all the measurements had to be changed. I wish that I could have just folloed Ana's plans to the tee, would have been a little easier. So after I assembled the basic frame, i assembled the top using pocket hole screws, glue and clamps. I used three coats of stain, with sanding between coats, two coats of clear Satin laqcuer and finished it off with a paste wax. Buffed the table with a cheesecloth and microfiber towel and then introduced my living space with a new, handmade table. My next builds should go a little quicker because I will follow the building plans exactly as they show. I hope you all like the table and look forward to hearing your comments on them, good or bad. Any suggestions to help me along the way would be greatly appreciated. Thanks for taking time out of your day to read this and again, I hope you enjoyed my first real, finished furniture piece.

Dennis

Check out all pics from this project in my Google Web Album by clicking on the blog link

Our Vintage bar stools that are not complete yet.

I could not find a big enough, awesome enough trellis in stores, so I built my own out of cull lumber [the stuff on super-clearance no one else wants] for about $12 and a left-over post pocket. Thanks for the inspiration!!

I built this after going dumpster diving for pallets. We went through and broke up all of the pallets and basically made this entire big piece for the cost of the stain, nails, and backing.

Inspired by Ana and driven by a desperate desire to nest, I made this table in my first-trimester. We live at this table. It's where we eat, play, and craft. On special occasions we stand on top of it, and sometimes we even eat under it. We love the way it looks in our mid-century ranch house with modern chairs. Thank you, Ana!

This was a lot of fun to build. Took a few hours while kids napped plus a few more after bedtime.