Community Brag Posts

Farmhouse coffee table with Red Mahogany stain. Pocket holed so no screws show. - Roger

I used Ana's Queen size Farmhouse bed with the modifications for the box spring. I also changed the plans slightly, instead of the 1" x4" on the footboard and head board I used 2" x 6" at the bottom. I don't have a nail gun or finishing nails so this provided the stability and saved me a few dollars. I also made the corner posts longer than the plans to make the bed taller.

I love this bed, I made it extra tall, so you have to jump into it. And there is plenty of storage underneath!

It took me and my dad about 4 hours of actual cutting and assembling, but an additional 10-20 hours of sanding and painting. It took me a few months to actually finish it after work.

THANK YOU ANA for the plans!!!

I modified the plan so that that I had a 48" table top and 4 legs only.  I didn't need such a long version in my entry.  The picture frame is from left over wood from the project.

Can anyone guess where I took the photograph in the frame?  Somewhere in the lower 48 states.

Thanks Ana for the design!!

Daren

Built from scratch looking at a photo someone sent me that cost $5200. I built for $500

Red oak 38x72 farmhouse dining table - The board professor

We constructed our farmhouse bed from rough-cut lumber (mostly pine with a few eastern red cedar panels). However, the top rails of the headboard and footboard were reclaimed from an old railraod depot and maintain their faded red color. I will admit, using rough-cut lumber practically tripled our efforts because nothing was square or even, but all in all, I think it was worth it!

Fairly easy table to built, just be careful measuring for coolers.

My husband built this table for me as an 8th Anniversary present.  It came out absolutely beautiful! For the first time,  we can host  family and friends with plenty of room. I paired it with some chairs that we already owned. He will be building the matching bench soon.

He left out the 45 degree diagonals,  may add them later.  It is so sturdy, they are basically decorative. 

I adapted a plan to create concealment nightstands with three hidden compartments. A quick access space on each side and RFID locking storage under the top. - Julie J

I was looking for something to make for my niece for Christmas that could be treated as an heirloom to hand down to future generations...thus, it had to be sturdy. My mother made the mattress, pillow, and blanket sets. I loved the way this turned out and my niece was pleasantly surprised!

We started with the basic chicken shed coop plans and modified it some. We wanted the peak to be in the front for ease of access and to allow leaves from tree overhead and rain and snow to fall to the back away from the entrance. The windows raise from the inside using 1/8" wire secured on the inside with a rope cleat hook.

We added Dutch doors. We added latches for the pop door to keep it iopen or closed as needed. Dutch doors also have decorative latches and eyehook latches to secure them when they are fully open. I rested the shed on 12 in. x 8 in. x 12 in. concrete patio pier blocks to allow drainage. we extended the roof about 6 " to allow for extra protection and avoid dripping whe  it rains.

On the inside I have a roost and a poop deck. Hanging from the poopdeck I have their feed to keep it off the floor and keep shavings, etc. from getting into the food. The poop deck  and the floor are covered with comercial grade tile to facilitate easier cleaning.

A delight for our daughter. We added an extra rung to the back rest, and kept the seat pretty high for her small babies. Otherwise, we just followed the free plan. Thx!

Waterfall table dressed up for Halloween. - Jeremy

Built this table using plans from Anna's amazing book. It was a much easier build than I anticipated. The actual finishing took longer than the construction. I did a slight modification by attaching beadboard to the top of the table. I had some leftover from a headboard my daughter and I made so I put it to use! Anyway, LOVE the table! Thanks, Ana! I would never have ever attempted building furniture without your virtual encouragement! Blessings!

Made this beautiful TV stand from the "Rustic X Console table plans". I shortened it to 2 ft high to fit the space for a TV. Love how it turned out!!

I needed a book display rack for my boys so I built this one from the plate rack plans and modified it to suit the size I needed. I actually used all scrap lumber from previous projects, so the cost was minimal.

Filled all the Knots with wood filler and sanded with 150g sandpaper. I used a Minwax Pre Stain Conditioner. Used Minwax Provincial 211 Stain. Finished with 2 coats of Minwax Semi Gloss Poly.

Dress up closet made from craftiness Is Not Optional's Dress Up Storage plans.