Community Brag Posts

Bedroom media center. Tv and fireplace with shelves.

We finished the deck this summer and wanted a large table to put on it. I saw the different versions of the outdoor Ana built. This one seats eight and has a tile inlay. For now...chairs from Walmart provide seating.

We were throwing all of our woodworking supplies into this closet off my patio, and it was really hard to find what we needed when we needed it.
So we made this shelf using two 2x4x10s cut to an inch less than 5ft each for the legs, and 4 1x3x8s cut to half inch less than 2ft each cut. (one board per shelf). (Measurements are for minimum waste)
Kreg jigged the 1x3s together 4 deep for each shelf. Used 1 1/4" Kreg screws.

We might go back and add a shelf or two to fix the odd spacing at the top and give us more shelves for the little things.

We did make some revisions to the plans, including making it shorter and not as wide. 

I am in process of making these for my new twin nephews. By reducing the width of the toy box by 1/2", I was able to fit two of the open top toy boxes on one sheet of cabinet grade plywood ($30).

For Two Toy Boxes cut plywood to the following dimensions (see photo for layout):

2 - 32 x 15 1/2 pieces (bottoms)
4 - 33 1/2 x 15 1/2 (front and back)
4 - 15 1/2 x 15 1/2 (sides)

My local Home Depot does not charge for cutting the plywood and the person that was assisting me made absolutely perfect cuts and helped direct me to the cabinet grade plywood (which was located away from the plywood aisle), thus saving me an extra $15.

Boxes took approximately 2-3 hours each to build, another hour to sand and fill screw holes, and several hours to paint.

Photo is of Dexter's toy box. Dante's looks very similar. My 2 year old niece enjoyed taking a nap inside of the boxes as well.

Make sure to purchase non-toxic paint.... I believe one of my nephews may be part beaver!

This bench for 2 was made of leftover pine wood planks I had in my cellar. I used different saws and a router to make sure the ends where smooth and give the overall project a elegant touch. Since I love to see the texture of wood I chose a walnut stain.

Made this over the weekend with my Daughter. Gray oil based stain. 

I built this a couple months ago and I'm finally getting around to posting a brag post. This is the second woodworking project I've ever done and my first year gardening! I almost spent over a hundred dollars on one of these raised garden beds and then I saw Ana White's plans and I am so grateful! Hopefully my tomatoes will be ripe soon, but one thing is for sure... this raised garden bed paid for itself with the amount of veggies I'm getting from it! I have big gardening plans for next year! Sorry my second pic is sideways... can't figure it out!

This was my first woodworking project and I absolutely love it. I think it turned out amazing and was actually very simple to do. I just got some construction grade lumber from Home Depot and borrowed some tools and got started. I did have to buy a Kreg Jig, which is an amazing tool by the way. I am not complaining about having to buy it since I have used it on many projects since!

A cutting board seems to be a right of passage for any new wood worker, that and making a mallet! I’ve already made a mallet and have been putting off making a cutting board so I figured now was as good a time as any. I’ve always liked the look of edge grain maple and I had some scraps of maple that were too narrow for most projects so I figured that I would go for that look. To spice it up a bit I decided to add a couple of accent strips of Oak.

I turned some old oak shelves that I got from an estate sale into a 3' wide Scandinavian slat bench.

Pocket Screws are my new favorite things! Total of 10 chairs made, 6 corners and 4 sides. Over 230 cuts, and 1000 pocket screws. It took me a while to finish, but I am very pleased with the result. I would not attempt this project without the Kregg Jig or similar product however. It saved me a bunch of time. The plans were detailed and easy to follow. I added a back brace to the design, and decided to make three separate units instead of a u-shaped sofa. This adds more armrests to the unit. I intend to add end tables in the corners and a table in the middle still. Instead of screwing the chairs together I used One-Wrap Velcro so the units can be reconfigured. I purchased the cushions instead of making them. Lowes had some on sale for $50. It added about $500 to the total cost, but it was worth not having to sew.

This is a project I completed last summer. I made some revisions to the original plan. First off, I wanted a corner sofa, so I had to figure out how the corner would work. This was my first ever wood working project and I'm not an architect or engineer, so it was quite challenging. I made a mini model out of foam core to give me a visual of how it would all work together. That was a tremendous help and I recommend doing this to anyone just starting out.

I did not use the part of the plan that included the foot pedestal. Instead, I built the sofa flat on the ground and in the end added store bought feet mainly because I liked the looks of them.

The sofa was built exclusively with the Kreg Jig, except for attaching the horizontal back pieces. I could have use the jig for that part as well, but liked the rustic look that screwing them in to the back braces provided.

I didn't want a padded back because the sofa sits outside on a covered, screened in patio year round. I wanted the ability to take off and wash all the cushions, or to use the bench without the back cushions sometimes.

The 2 sections of the couch were built as independent units and are movable, so one can sit across from each other. Both sections have ample storage.

My husband and I took this on as our first project.. very happy with the results!! Our american bulldog gets kennel anxiety so we thought we would try this and he loved it right off the back! It is nice and lg he is 90lbs and our little one has made his way in with him to and he is 25lbs they both fit comfortably!!!