Community Brag Posts

We changed the plans for this kitchen island a bit to best suit our needs. We removed the middle shelf and the bottom half of the center divider in order to create a large, open area for storage. We also extended the bottom slats to the full depth of the island, or 21".

The drawer depth was also increased to the full depth, or approximately 20". Instead of using 2x2 cleats for the drawers, we installed 20" self-closing drawer slides from Lowe's. This allows the drawers to be fully extended as well as have a soft-close feature. 

The top measures 26 1/4" x 56 1/4" and was made by securing two pine panels together using pocket holes. We couldn't find an appropriate size at Lowe's, so we purched two panels instead. After sanding and staining, it is impossible to tell where the boards are joined together. 

In the future, we might distress or add an antique finish the white base. Overall, we are very happy with the kitchen island. It's wonderful to have a little extra storage in the kichen! 

Thanks Ana!

-Anna

I built this to hold my son's toys, which seem to multiply by the day.  It's very sturdy and has lots of storage room.  I printed out the lettering on paper, put the paper on top of the wood, and traced over it hard to create an impression on the wood.  I then used the feight lines as a guide to paint the name.  

Wow! Did we ever pick a "small" project for our first build:) We had never built so much as a birdhouse and here we were building a playhouse. It was so much fun though and I'm glad that we did it. My daughter LOVES it and we are so pleased with how it turned out. We ran across a few problems due to our inexperience but nothing we couldn't overcome.

I just made the center part of the console.  My daughter didn't want any cabinet doors or drawers on it.

It started out being painted yellow, then she changed it to the distressed light green in the first pic.

Made this for my granddaughter and worked on it 40+ hours. I borrowed the removable window boxes and shutters off another plan to girlie it up. If I were to make it again, then I would add an extra 2 inches on the sides, front and back to make it easier to make up the bed. It's so adorable and I can't wait for her to see it. 

Made this for a friend. Followed the plans from the Clara table, chairs were made from the 4 dollar stackable chair plan.
Finish was Watco Danish Dark Walnut oil, which i just discovered and love. Goes on even and isn't blotchy on pine. For the table top i added a couple coats of polyurethane.
The table was easy to make, but the chairs took quite a bit of time with the amount of slats. Also there are about 30 screw holes per chair to drill, countersink and fill with putty. I am making another set for someone else, and will probably go with a single, wide slat for the back and seat. Also I would suggest adding braces to the legs, they seem a little flimsy

I built this for some friends who are having a remodel done in their house to get their washer and dryer out of the kitchen.  The new area was a perfect size for a cool piece of furniture and because of how well my other projects turned out they asked if I would make something for them.  My friend is a great cook and has some really nice cookware that needed housing so we used the "planked wood sideboard plans" as the bones for the project.  I saw some cool things from Pinterest (Glideware) that I wanted to incorporate and we drew up some plans.  All in all it took me about 36 hours to complete. Two weekends and some work at night after work.   I used my miter saw, table saw, circular saw, power drills, wood clamps, Kreg pocket hole jig, and my electric sander to knock this one out.  

I just want to thank Anna for inspiring me! I would've never thought that I could actually build my daughter a loft bed from scratch if it hadn't been for this website! This loft bed took about 3 weeks to build but the reason why it took me that long is because I did it in my spare time which was a couple of hours each alsmost everyday excluding the weekends, also this was my first time using my husbands table saw and drilling pilot holes but once I got the hang of it everything went smoothly. I wanted to save money so I purchased the Mini Kreg Jig which is about $20 from HD and let me tell you it is a must when your drilling pilot holes. I purchased my lumber from HD as well. It took me about an hour to pick out the wood. I decided to paint the loft bed with DecoArt Enamel craft paint because it's non-toxic, the paint cures into a hard finish, no primer, I didn't have to sand in between coats,  or put a protective finish. It also dries fast. I put 3 coats. This paint can get pricey if you pay full price but I just used a coupon everytime I went to Hobby Lobby. I used a tea, vinegar and steel wool mixture for the stairs, again because it's non toxic. I also raised the height of the 2x4 posts 6 inches so my 7 yr old daughter could walk under there without hitting her head. I'm so glad I decided go for it! Thanks again ANNA!

I wanted to build my kids a sand/ water table, but wanted something that would could also serve as other purposes. My father helped me since I used his tools. We shortened the whole project by 16% so my kids would be able to reach it better. We also changed up what wood was used. My father came through and had a pile of wood that he had no use for. So we used 1x6's that we cut down for the shelves and 2x4's for everything else. We also added a brace on the back to add a little more stability to the bench since my kids were going to use it. To finish it up I bought a plastic storage tub with a lid and some sand. The bottom shelf is used for toy storage.

I used the Rebecca Side Hutch and Side Base plans to create a slightly wider version to fit the TV in our master bedroom.  The building took one whole weekend and then it took another week to finish it up like filling holes, sanding, painting and then reassembling.  My final cabinet is 36.75" wide at the top and I changed the doors to overlay instead of inset.  I love the finished cabinet!

I made these chairs and table for my father as a Christmas gift to sit next to his pool. The chairs were fairly easy to make. To stay within budget I did use inexpensive white wood so the quality of the grain was not quite what I had hoped but I believe they still came out very nice. I used BEHR weather proofing wood stain in RedWood which turned out very nicely. The only thing that is currently lacking are the cushions. Due to the price of the foam that will have to wait.
For the table I started with the original plans on the site but when I realized just how long it would be I cut it down and added the two thin strips to break up the pattern.

If I were to do anything differently I would shrink the overall size of the chair to the size of standard cushions that can be purchased at local department stores or outdoor furniture stores to minimize the cost.

Used a 2x2 cut at 45 degrees on both ends to hold up the flaps.

My wife wanted an 8 foot long table, but wanted it to be a little narrower that as standard table. This one ended up being 97.5" x 29" I used a torch to scorch the wood then apply poly finish.

We have quite a fixer upper and while re-doing the bathroom, I came across Ana's Island plan in her book, The Handbuilt Home. This isn't the finished picture as we have installed the sink fixture and pipes, where I wrapped the exposed pipes with twine to give it a more rustic look. The table was modified in size and the mirror was a salvaged piece where I made a backer and framed it. Though still in need of some finishing touches, the look so far is spectacular... I wish I had a before and after photo. Much of what you can see, such as the tile in the shower and mirror has been made from found materials around the house or were items that were going to be sent to the dump. I love recycling!

New to building,

Stephanie Broker

Went a slightly different route, since I'm not a fan of furniture built using 2x4's. I opted to use 1x3"s for the supports. Still more than sturdy, and I think it adds a little to the look.

Shrank it down to 28" x 28" to match the size my wife wanted. At that point a single drawer on each end made more sense for them to be practical. This was my first furniture project, so lots of mistakes were made, but I learned a lot. I look forward to many more projects from this site.