Community Brag Posts

My kids needed a step stool and I had some scrap wood (2x10) left over from a previous project

A new home for 8 ex battery hens. :)

ManicMick

We loved the storage of the Farmhouse bed, but loved the headboard and foot board of the Kentwood. We also wanted a twin size bed. Instead of trying to figure out the measurements to make the farmhouse to a twin size (which is shorter in length), we made it at the full size length and just bought XL twin size mattresses, which were not hard to find and now we can keep the beds even after our boys become teenagers :-)

We basically built the headboards and foot boards from the kentwood exactly as Ana's plans state. Then we built the Farmhouse storage drawers. We love them!!! Thank you so much Ana for MORE great bed plans (this is our second set of bed plans we have made!

This was a project undertaken to facilitate my current pursuit of learning how to cook, but I think it will serve me well as I study, too, holding my textbooks up. It also let me experiment a little with staining and with using milk paint (which has NO VOCs but is kinda weird to work with). And it let me put to use some scrap wood that I think I was unconsciously saving for something special.

Because I had a scrap pile, screws, a few hinges, and the finishing products, this project was Almost free...I had to buy a narrow hinge ($1.50? I think?), and I chose to buy some pretty page weights ($3 including both pendants and the chain). So...not too bad, right? For a solid book stand that has meaningful beauty to me?

Ok, so this is all scrap wood. The stained pieces are maple leftovers from my cabinet project, and the rest is a mix of pine and poplar. See the dimensions in the last photo. The paint is Miss Mustard Seed Milk Paint in Lucketts Green, and the stain is Red Chestnut oil-based stain by Minwax. I finished the whole thing with one coat of wax buffed to a soft sheen (my new favorite finish).

I used a miter saw for my cuts and a router for the kickstand grooves, but really a regular circular saw would've worked just as well (or better, for the grooves). It took me several days to finish this project, but there's no reason it should take (someone other than me) more than an afternoon.

This was a pretty easy build, always a plus when you're looking for more storage. I'm not sure about the darkness of the stain though; I usually go with a walnut to match the rest of the house and wanted to try something different. This seems like a bit much. Might be easier to build an entire second set vs re-doing the stain though...

This thing is a beast ! I made the top way thicker than I should have but I love it.

I made this table before the PB plans came out on the this site. I used gate hinges on the corners and 3/4" piece of all thread on the bottom. The top was poured with the High Gloss glaze from Lowes. It fits 8 all around and you could squeeze in 12 if you really needed to. All together this only cost $350.

This was built off Ana's Outdoor Couch plans.  I just made some additional things to it and made it larger.

I added the vertical back supports so the cushions don't slip out the back.  I raised the seat height to 17". 

Shelves in garage

I have to admit...I'm an Ana White and Pintrest addict. I was visiting my cousins farm and saw a pile of beautiful old & weathered barn wood. She let me take a big pile home. I washed and scrubbed the wood with a soft brush to get the years of dirt off. After dried, I layed down all the wood and picked out all the neat character pieces. I freehanded a template of the headboard on butcher paper and traced it on the boards. I cut the boards and lightly sanded the edges. I brushed on two coats of clear coat. When dried my hunky hubby helped me put it all together with 1x2"s and screws. We attached it to the bed frame and there ya have it! A gorgeous traditional-rustic headboard!

I am a really beginning builder (read: this is about my fifth project ever), but it works perfectly for our really tiny, narrow bathroom. I finished it with some stain we already had on hand. Thank you so much for the building plans!

We've been talking about making this for quite some time now, probably close to 6 months. Mostly because we've never made anything before we kept putting it off. We had a free weekend and decided that we needed to complete this project that's been hanging out there for way too long. We'd researched where to get the wood, and what we wanted, but still did a little more planning. Thursday night we went to the big orange box and checked out their options for 2x4s, plywood and moulding. Friday I went to our local Ace lumber yard and looked at their options.

Friday night we decided to get the 2x4's and plywood from Home... the big orange box since their plywood was much more level. We paid a little more for the grade A plywood, but didn't want MDF as it will disintegrate when it gets wet. Not planning on getting things wet, but just want to be sure.

We got the moulding at the local supply store along with screws by the pound and corner brackets.

As you can see in one of the photos, we had the store cut the plywood for us as we didn't have access to a table saw. We borrowed and used a compound mitre chop saw for the rest of the cuts. Since we had so much leftover plywood and really liked the look of Sausha's wider pillars, we decided to go with facing out the front and left side (the only ones visible in our location) and columns and put moulding on the front and one back leg showing. For the moulding we only faced the back and right leg with two pieces. In hind sight as the pedestal doesn't go against the wall we could have gone all the way around, but that might have added another weekend.

Saturday we started out getting the rest of the necessary wood, laying out the boards and deciding how we wanted to proceed. We ended up following the directions and not making any changes to it. The only change I thought about making was to take the 2x4's all the way to the ground rather than mount them on the bottom decking. We decided since this has been made quite a few times and haven't seen any bad reports, we'd stick to the plan.

Saturday we worked about 9 hours total putting everything together, facing out the project and filling the screw holes with wood putty. My only regret at this point is that I didn't fill the top edge of the faced plywood all the way across with putty. In order to get a much cleaner look, if I were to do it again I'd have bought a tub of wood putty and filled the entire edge to eliminate any holes or spaces from the edge of the plywood and the seam between the face and decking.

Sunday we started out by sanding the wood putty down, reapplying where needed, sanding the rest of the rough edges flat, and then started on moulding. The moulding took a better part of the day to get the angles right, and thankfully we had the compound chop saw that would do greater than 45 degree angles. We glued and nailed the moulding down, and then took the project into the garage to paint as it was getting late on Sunday. Three coats of paint smoothed out all the edges. Be careful about drips on the corners. We decided to go with something other than 1)trying to match the washer/dryer and 2) black as it might attract too much lint and show. In the pictures it's actually a lot more purple than in real life, but it's a gray paint with a tint of color to it, Behr premium primer and paint in one.

We put the stand in place Monday evening, although the paint was still slightly tacky. The hardest part about the end was getting the washer and dryer up and hooked up. We needed to put the washer up first and connect it as the hookups were behind the dryer and no way we could have connected it with the dryer in place.

We love it! It's raised the washer and dryer up to a decent level, saved us at least $350, and now have room to put baskets underneath. The whole thing rattles quite a bit when the washer spins up, but so does the house and the TV stand 2 rooms away...

Due to a few bad cuts, we ended up having to get an additional strip of moulding. If you're not experienced in doing moulding, plan on a LOT of waste. ;)

Our next project needs to be a matching recycling center which will go right next to this.

This is my third project - built the Full Farmhouse bed and Haley platform bed. Son wanted a 6 ft table to accommodate all of his computer/gaming devices.

Came together quickly - sanding/stain/finish took majority of time. Stained base with Minwax ebony (2 coats), used Minwax weathered Oak on table top (1 coat) and 3 coats of Satin Polycrylic.

I now have a long list of projects....

Built 2 twin beds for my granddaughters.  They turned out great and they love them!