Community Brag Posts

Pretty easy project.  Check for square often.  It will pay off when putting the shelves in.  The "x" on the sides was the trickiest.  Cost was approximately $100.

I made the top removable by attaching blocks to the inside corners of the apron and using a spade bit to drill a hole.  Then attached hanger bolts to the table top and fastened with washers and wingnuts.

I was in the shop on Thursday and decided to build something with the endless supply of 2×4 wood scraps I had collecting in the corner. We had been looking for a wood shower organizer since we moved into our new apartment, so decided that would be a good project to tackle. I few weeks ago I found a teak shelf that would have been perfect for our bathroom, but was not willing to pay $119. I designed a shelf in the style of the teak shelf I liked. Untreated pine is not suited for a wet environment, so I went to Home Depot and bought a can of waterproof epoxy for the finish. The end result is a very simple and functional shelf.

Treated myself to a load of new electrical tools and bought a kreg jig, this was my first project of this size for many years and also using the pocket hole method, my wife was very happy with the end result as was I. The doors, all made from scratch using the jig also finish the shrine off well. I'll be hunting around on the site for a new project soon, this one took me a lot longer to complete than I anticipated, it ook months before I finally managed to finish if off but then I had an issue with the amount of time available I could spend on it on a weekly basis.

Made from following these plans, and using scraps I already had.

This is my first project.  With some help from my husband (navigating the power tools-- the table saw in particular) it was completed in a few weeks.   We live in Army housing, so I never really know what kind of space we will get. Inevitably, there is never enough storage, so this will find a home in any new home we might live in.  I used beadboard for the back, stained minwax special walnut. The paint is Benjamin Moore serenity blue- and then I used acrylic polyurethane- adding another level of kid resistance;)  Great plans Ana, and I am so excited to do my next project!

Modern style coffee table

I did these as a birthday present for my husband. He is very picky about seating, but he said these were very comfortable! I used 1x4 oak for the headers and pine for the rest. After reading others' concerns about the support dowel, I decided to do the following:
1. Drill a 3/4" hole halfway through each 1x2 support with a 1/4" hole continuing the rest of the way through to the outward facing side of each
2. I glued a 1/4" dowel into one 1x2, pushing the dowel as flush as possible to the outer edge of the 1x2. I then slid a 3/4" hollow steel tube onto the wood dowel, and into the 3/4" hole in the 1x2.
3. Finally glued the other end of the wooden dowel into the other 1x2 (which forces the steel tube to nest into the 3/4" hole in the 1x2) and trimmed the excess dowel flush. The steel tube acts as the support, and the 1/4" wood dowel simply holds it all together. Did that make any sense?

If you can possibly avoid paying full price on the fabric, DO! That alone accounts for 70% of this project's total cost!

We made this in just over 2.5 hours with the kids "helping."  We made it a bit taller, with the seat at 19 inches, so the leg pieces were 25.25 inches instead of 18.25.  Because of this, we will probably add two supports across each side as it seems a bit wobbly when the kids all wiggle on it.  Now we finally have a seat where all 3 kids can sit together to play on the computer.  Thanks for the plans!

I used the Rekourt plans for the most part, but I did change it a bit. I needed a smaller table, so I adjusted the plans to accommodate this. The table is 5 feet long with matching benches that are 4 feet. I eliminated the 2nd cut on the 2x4s used to construct the table base to simplify the look. I also made custom benches to match, as I could not find any plans that were an exact match on the site. This is the first time I've built anything, and it took some trial and error and a lot of muscle. It was well worth it though!

I had a lot of fun making this. I am so excited to be using it. Ana's plans were easy to follow.

This was a project to use some pieces of left over ¼” thick aromatic cedar closet lining board.  I cut off the tongues and grooves with the sliding miter saw, and calculated the measurements for the box to fit the size of the wood.  For this build I used the micro-pin nailer with compressor, and ½” headless pin nails.  The finished box measures 4 1/8” tall, 6” long, and 3 3/8” wide.

Inside, a divided lift-out tray sits on rails made from small pieces of the cedar board glued to the inside.  The addition of an extra decorative board to the top made it ¾” thick, to work with a regular knob.  The inside of the box stayed unfinished to preserve the cedar fragrance.  This was an afternoon project.

I've wanted to build one of these forever! I changed the plans a lot to accommodate my needs, but I loved the idea of faux drawers on the doors to have an authentic look. It fools most people! Took 2 weeks for me to complete, working on and off. It has great storage inside for all the kids' stuff I didn't have a place for previously. The stain is ebony by minwax and the hardware pulls I purchased for under $10 for 30. 

Built these for my daughters for Christmas. They are super easy and fun to make!

This was just a quick little project as we decided we needed a bit of organisation in the office.

I just used scrap mdf and leftover bits and pieces from other projects for this wall file. We now have somewhere to put all the postage stuff for our online sales site.

Cheers... Nay

Our son Liam-Joseph wanted a "Big-Boy Bed" and then he added "I want Daddy and Santa to make it".  Well "Santa" and my wife Jacques looked all over the internet and finally found your Cabin Bed via jennwoodhouse.com.  Jacques altered the plans demensions and she realized the bed could be barn-like so she came up with the red and gray paint job.  She actually wanted a cupola but I thankfully talked her out of that.  Well somehow we keep the construction from Liam 2 weeks before Christmas.  On Christmas Eve Liam's Grandparents keep him at their house while "Santa" and I put the bed together (I never did a trial run so I was relieved when everything fit right together).  The next day after opening his presents he ran up to his room and saw his bed for the first time.

The project isn't completed.  I recently finished the roof with wood pallets but I need to finish the trimming of the interior of the bed walls.  

I built a couple benches to go with the reclaimed wood farm table I recently built. They are made out of hard to find 2″ reclaimed rough sawn lumber. The benches would also make a great coffee table or side table. Each bench is 36″ long and 18″ tall and 9″ deep.