Community Brag Posts

A great one board project using some left over cedar that was collecting dust.  Using a 1/2" round over bit I eased the outside corners as well as the drawer sides.  I find that the drawers will slide easier with a slight round over applied.  I left the cedar without a stain and two coats of satin clear.  

Needed more storage and this project was so easy. Tied in the baseboards and crown for a built in look.

- Used a router to cut a dado slot for the vertical boards to slide into the 4x4 posts so I would not have to screw them in from the outside

- Used a router to round over the edges to make the post toppers.  

- Used router to give a shaped edge to the top horizontal planks

- I bought the finials for the post tops

Barn board flags made from a dilapidated barn.

I scaled down the large rustic x bench plans to create seating for my grandkids at the new kid's table.

I got the plans from Anna White $50 beginner farmhouse table build. Changed from a 6 ft table to a 5 ft. Built in a few hours but took longer to paint than anything because it took 2 coats. 

I only recently stumbled upon Ana-white.com and was amazed by all of the wonderful plans and tips here, not to mention the community. My wife and I had inherited a king size bed after my grandparents passed away. While we were both grateful, the bed was on a very basic metal frame that sat very low to the ground and was hard to get up out of. My wife had often talked of having a nicer bed to put our mattress and box spring on, So with great eagerness I set to work. I loved the classic look of this bed and was a bit saddened that there was no king-size plans available. I decided that wasn't going to deter me, so I set out to modify the plan to fit. After making a few adjustments and modifications, the bed really started to take shape. Needless to say, I am very pleased with the results! Thanks everyone, and thank you , Anna!

Great plan! I curved the edges with a French curve and a bench sanding disk, and then used a router on all exposed edges. I used a dremel router table with a small bit for the small pine pieces and a full sized router for the two main platforms. If I were to do it again I’d be far more careful with angle accuracy.. I think my miter saw is a little off. My table saw was spot on for the plywood cuts. I also used smaller wheels and only have spinners on the front, preventing collision.

LOVed building and painting this. Although using European wood is a headache as of course the standard wood sizes are different. ... always 4-6 mm off... so all my things are crooked. I don't care though and it is my new favorite chair. I used ArchiTect blue exerior color, two coats, and pine wood.
I am grateful for Ana White's metric conversion chart in the book I now have but when going to the hardware store here, I am confronted with numerous standard wood sizes that are not the same as in the US!

Friends of mine are having a girl and needed a bookshelf for the nursery. Loved the simplicity of this design and wanted to see in an antique white finish. Great plans and design.

I added an additional detached shelf so we can change the setup anytime. I also increased the space between the two main shelves to 30 inches and extended the depth to 22 inches overall. I left one shelf off to make room for the computer tower. The top is made from maple with a gunstock stain. This desk will mainly be for my kids gaming station. 

(I don't know why my picture is horizontal, it shows up fine on my computer).
In redecorating my oldest son's room, we needed him to have a loft bed, but all the commercial loft beds are too tall for his bedroom. So then, we thought we would re-work his current bunkbed. In order to use it as a loft bed we had to remove the bottom support rails and that meant we needed a new solution for a ladder (because it was part of the support system). After looking through the site, I decided that this ladder was the best for our needs. The ladder went together smoothly. We had to modify the directions just a bit to make it the right size. We put a set of U-brackets on the end of the ladder to put over the bunk bed. We also drilled through the bed frame and into the ladder for additional support.

This took about 6 hours from beginning to end, but next bench should take about 4-5 hours. Most of the time was spent on sanding the wood and waiting for the stain to dry.

Main lesson learned: Drill pilot holes throughout. I used no-drill construction screws, but it didn't pull the wood tight enough against each other. Also, stain all the wood pieces before assembling (as opposed to just the top slats as suggested in the plan). Remember that the leg pieces will not need stain on the flat surfaces, just the sides that will be exposed. Use a square tool to stay as close to 90 degrees as possible.