First Rustic X Console table build
First stab at this table turned out so well a friend bought it off me and I had to build a second.
First stab at this table turned out so well a friend bought it off me and I had to build a second.
Dear Ana White,
I was looking for an inexpensive shed to build and saw your lean to. I love it and get many complements. Thanks for your site and what you do.
James got a sweet retro kitchen set for Christmas from his grandma. CarpenterMama scored a kids kitchen table (pretty sure it's authentic retro) at Goodwill for $8. All that he needed was a chair to sit in, and Ana's Four Dollar Stackable Chair fit quite nicely!
This was CarpenterMama's very first building project, and she is as proud as punch that she made something with her own two hands, some wood & screws, and oops paint. James is ecstatic that it is blue and he can sit in it. :-)
sofa table made from console plan, I just changed the measurements.
We built this over the course of a couple of weekends. I think the key thing was making sure my 1x6's were the correct width before we began to cut all the other boards. There was a lot of trimming after the fact making the overall width 1/2" shorter than the plans. Some adjustments made to the original plans were...
1) Using decking brackets to support the plywood to the 1x8s on the trundle (super easy way to secure it)
2) Purchased side rail brackets exactly like the ones here from my local woodworking shop.
This makes the bed easy to disassemble because although I swear I'll never move again I'm not building the bed into the room.
3) Instead of casters on the bottom we used those plastic furniture sliders. They were way cheaper and so slim. With the weight of the trundle wood and mattress they move flawlessly.
4) Since my daughter has a memory foam bed I was worried about sagging. We used small 1x? ripped in half along the inside of the side rails for a little lip and then 4 1x6's the width of the mattress to make supports and then laid plywood on top of that. 5) Cut down the headboard by 6.5" so that the mattress butted up against it.
Me personally I hate when there is a gap there for pillows to fall down in the middle of the night.
This is a pretty easy project and makes a nice holiday gift. This version was made from a scrap piece of hardwood and a 5/8" dowel. As an extra touch, I added a compartment inside the board to store the pieces. The compartment panel is held on with magnets for a clean look.
The quick video shows how the compartment works.
I painted the outside with Benjamin Moore Balsam color paint (as another poster on here did) and stained the interior pine with walnut stain. I tried making it resemble a pine tree. I wanted to make it as sturdy as possible, so I used 1/4 inch plywood backing for the entire back, and secured it with 1 inch brad nails. I painted the edges of the plywood green and left the middle unfinished because I liked the look.
My husband made this chair in about 30 minutes. It was are first project from this sight. So easy and my niece loved it!! I painted he cut! what a team
This was my first Wood Project - EVER.
Working with this plan was quite easy. I just changed the design of the table top to my wife´s wish. I used "Golden Oak Stain" for the Legs and "Provincial Stain" for the Table top and Bench. The Legs are covered with Water seal and the Tops with 3 layers of Polyurethane. Chairs are Stained in Provincial also. Was a lot of fun for all of us. Learned a lot during this build.
Thanks
Mon, 07/01/2013 - 21:10
Thanks for the nice comments. I bought the Chairs at a local Mexican Furniture Shop, sanded them, Stained them to fit the Table Top and put 3 layers Polyurethane on it... Came Out nice.
Thanks Alain.
Jann
This has probably been done before but here it is for consideration by my fellow woodworkers. If you're anything like me I get pretty impatient waiting for wood glue to work its way out of the tube. So using some scrap wood, I drilled 1.5 inch holes in a small 1x4 board and elevated it about 3 inches. A small board under the glue tubes catches any unwanted drips. Makes a perfect caddy for my glue tubes and no more waiting for my glue. Its always ready to go!
Wed, 06/03/2015 - 06:25
Nice way to keep them collected AND ready to go.
Could do the same for condiments, maybe.
I sent these plans to my dad and said I wanted him to help me build it for Christmas. He came with everything cut and ready to be sanded and assembled! It was put together and stained in a day! I love my Christmas present, and love that my dad and I built it. It will be a family table, for sure!
This was a great project to build, easy directions and easy to make modifications to. I built this bedroom suit for my son and his bride with their brand routered in the middle and used black epoxy to fill. Used Miniwax Honey colored stain and finished it with two coats of Danish Oil to protect it.
This was my first project. My wife saw it and told me to make it :)
This was my first bigger woodworking project, and I loved the project and the plan! I'm just starting out buying tools, so the only power tool I used for this was a drill. I also have yet to get a work bench, so for now I was just working on the floor inside my apartment.
In order to use up some leftover wood, I made the sides out of several boards instead of one solid piece. I didn't use pocket holes for lack of a jig; instead I simply glued the boards on the sides and connected them with a few thin screwed-on boards inside. I will still line the inside with some sort of cloth, so I wasn't too concerned about what it looks like inside.
Considering my circumstances, I'm extremely pleased with the results, and ready to soon move on to another project.
From start to finish it took me about 3 weeks of working on it about 2 hours in the evening maybe 4 days a week (mind you, I'm a beginner and was using hand tools).
Sun, 07/07/2013 - 21:31
You did a very good job considering you did it all by hand. When I was afraid to use power tools I made my sons first bed by hand so I know how difficult it can be. Since you already have a drill I'd suggest getting a miter saw next. It will save so much time with your cuts. You'll also get perfect angles. :)
I dont have a pocket hole jig either but if you still want pocket holes you can buy a countersink drill bit at just about any hardware store (or use a regular drill bit but the countersink ones work better, I feel) and angle it at 15 degrees or so. Then just sink your screw right into the hole. Viola, hand made pocket holes. :)
I love the dark color too, job well done
~Melody
I found the Workbench Console plans on this site and thought it would look great behind the sofa.
The length was extended to make it comfortable for 3 people to sit at and also to span the length of the sofa. I cut out a section at the back and lowered it to hold some glasses. This fits 4 beer glasses, 4 wine glasses and 4 shot glasses. The towel holder is a cast iron key that I found on Amazon. On the other end is a cast iron bottle opener found on eBay.
I would like to take credit for the chairs, but I cheated and got these from IKEA.
We love using this while eating dinner and watching a movie and is especially handy when guests are over.
Made this Accessory Holder as a Christmas gift for a male cousin to hold his phone, watch, ring, glasses, and wallet. Comes apart for easy movement. I like the two-tone of the stains and the simplicity of the holder. Router kept giving a bit of kickback, biting into the wood where it was unwanted, hence the messy cord line, but as with most of my projects, I don't mind the mistakes that make them more "unique". Artistic choice? : ) Also difficult was figuring out the angle to cut the opening slot for the side piece. It needed to be angled to set the side piece just how I wanted it. Eventually decided on 10 degrees.
The idea for this holder was based on this: http://cleverwoodprojects.org/woodworking-projects-for-beginners-six-ea…
Don't read the site- it was clearly written by a bot or ESL individual, because it's mostly gibberish. Just used the image for inspiration.
I freehanded a design that then was drawn on the wood and had plenty of fittings and mockup pieces made throughout to figure out how things would fit. Fun challenge, great gift.
The table is based on the farmhouse table with pocket holes. I used a mulwark pocket hole set. The bench was made with all scrap lumber and I ended up being short on 2x4 wood, so I used 2x2 on each side to accommodate the same dimensions. It was a time crunch, but I got it all done before Xmas Eve and it looks dope.
Sun, 12/26/2021 - 13:49
Oh yes, that is dope! Thank you for sharing, love the finish choices!
I built Ana's Reclaimed Wood Headboard. This was the easiest piece I have built so far! Very quick! You can see the steps I took to finish it at our blog http://www.shanty-2-chic.com/2011/04/diy-headboard.html
We've made the decision to homeschool our almost 5 year old daughter starting in September. The dining room will be the school room, but I don't want to lose my table in the process. So I began looking for good storage options. I saw the Display-It-Storage Mirror on the PB Teen website and loved it! Right up until I choked on the price tag. I went inspiration hunting and found Ana's Willy bookcase plans. I modified the Highrise Condo Willy bookcase, added a base with lazy susan hardware and a top outfitted with crown molding. Then I bought some cork on Amazon to create a cork board on one side, a role of dry erase paper to create a dry erase board on the other side and framed them. On the back, I hung a bathroom organizer with lots of pockets for dry erase pens, push pins, pencils, tape, scissors, etc. Finishing touch was my daughter's choice of scrapbook paper for the inside backing.