Community Brag Posts

I love my dogs, but their wire kennels were an eyesore. Removing them completely was not an option, but I was tired of looking at them. I went back to my first-ever rehab project, and took it one step further to create a one-of-a-kind castle for my pups.
The original piece of furniture was an old console-style TV cabinet. Sliding doors on the front revealed the TV, and two lids on top contained the tuner and a turn-table.

Armed with screwdrivers, hammers and a dremmel, all components were removed form the cabinet, leaving just the shell. (PLEASE be sure you remove all sharp, potentially dangerous, screws, staples and what-not’s from the inside of the cabinets, to avoid injuring your pet! The dremmel allowed me to cut off and grind down stubborn screws.)

To cover the holes in the top cabinets, I used old checker boards. The cubbies are now a great place to store dog treats and leashes.

OPTIONAL: The back panel of the cabinet I used had holes from the TV components. I elected to replace the back board with a new sheet of peg board. (The peg board allows for much-needed ventilation.) In order to get the size perfect, I traced the old back onto the new and marked the original screw holes.

I vacuumed the inside to remove all construction debris and polished the exterior with Pledge. Then, I inserted an old comforter into the kennel, and stood back as my two pups launched themselves into their new abode.

The doors can stay open during the day for them to enter at their own will, and close for bedtime. And my eyes no longer hurt.

He likes natural wood, I like painted furniture. Solution: two-toned bed! Vertical slats are stained in Minwax Red Oak (took 3 times to get that dark color!), surround is painted black. I thought we'd never find a workable compromise!

I changed up the dimensions a bit to fit my preferences:
1. I like a taller headboard and footboard (dog can't rub against the end of the bed anymore - wahoo!).
2. Also wanted the bed to be just a bit higher above the ground so I wouldn't have to buy new under-bed storage boxes.
3. Used 1x6s instead of 1x8s for the vertical slats because they fit the width just perfectly - no trimming needed.
4. Added about 2" to the length so I'd have plenty of room for tucking the duvet at the end of the bed. I hate when the covers get stuck and I can't pull them up easily!
5. I routed out a groove in the posts to slide the side rails in because it seemed more secure than screws alone. Could've done it without, though.
6. We used dowels and wood glue on the 2x6 tops of the headboard and footboard pieces. I think it made a big difference in the overall appearance. We don't have a doweler, but the hubby made a guide with a spare 2x4 to keep our dowels lined up correctly. It worked pretty well.

Next time I would use pocket screws. I've acquired a jig since this piece was completed. It would definitely have saved me some time in the finishing process.

I really wish I could have talked the hubby into letting me distress the finish just a bit. The thing is, it's inevitable around here (my kids are like crazy apes sometimes!). So I really wanted it to at least look intentional. Oh well, I guess we'll get there soon enough even without it!

Built for our 4 ur old son.. We all love it and had fun together!

A piece of Palouse/Moscow/North Idaho History!

Hand-crafted by father and son from reclaimed materials native to the region, this is a one-of-kind piece of furniture of both substance and significance.  The stock was sourced from the railroad depot that stood on the University of Idaho campus in Moscow for well over 100 years.  The crops, forest products, and people of the Palouse passed through its doors and across its floors from the early days of westward expansion and settlement.  Marked for demolition in 2017, the depot yielded lumber that had been harvested from old growth forests native to our region since time immemorial.  The trees that produced the lumber-turned-dept-turned-halltree stood tall, proud, and mature at the time of the signing of the Declaration of Independence.

The halltree’s back panel and trim are crafted from the depot’s tongue and groove flooring, and still bear the marks of their original milling.  The remainder of the piece is constructed from the ceiling planks.  Twice painted during the course of the depot’s sentinel watch over the commerce and culture of our region, the cream surface coat is yielding to the forest green base layer, giving the finish a depth and patina that testify to its age.  The history of the Palouse literally passed over, under, and between every square inch of wood in this halltree!  It now stands ready to serve a family for generations to come while reminding them of our pioneer past.

Dimensions:  39” x 15-1/2” x 78-1/2”

I made this chair for my 3 year old son's Birthday, he loves it. Really easy build.

Pine box with walnut top and drawer faces. Behr paint on the box and tung oil finish on the walnut. 

We really liked the plans for this table, but it was too narrow for our taste. My husband altered the plans so that the table is 36" wide. The solid oak boards on the table top are reclaimed from the old barn out back.

I built this dresser for a little girl. It was my first time doing drawers and I was a little intimidated but it wasn't bad at all! I'm going to be building one for my sons room too. Thanks for the great plans!!

I got this Idea from Sausha's washer dryer pedestal post.  Before then i didnt know people even built pedestals for their washer and dryer.  Just purchased new front load washer and dryer and they wanted 250 bucks extra for each pedestal.  That is 500 bucks and is absolutely rediculous.  So i opted out of those and thought to myself maybe I can build something instead.  So I began my search online and stumbled across this post which seems to be the most popular pedestal build on the web.  I think sausha's build is fantastic and absolutely beautiful though I went another way with mine.

I tend to like to overbuild things.  Especially in this case, seeing as the washer weighs a beastly 200 pounds by itself.  I figured with clothes and water it would be about 235 pounds just for the washer.  I noticed that with the aluminum drawer pedestals that you can purchse with the washer and dryer the support is only where the legs from the washer and dryer will sit.  That was all I needed to get on my way.  Purchased some regular old douglas fir 2x4's, 4x4's, and a 4'x8' sheet of 3/4 inch plywood.  I opted to use fence post brackets to tie everything together because I didnt feel like driller pocket holes in each 2x4 when you were not going to see them once its all said and done.  The fence brackets are not structural so they lack ridgidity untill you tie everything together with the legs, slats, and top.  Cut the top from the 3/4 plywood sheet and used the left over plywood to cover the front and the sides.  I left the back open as it is not seen anyway. 

Total size of the pedestal is 56" wide x 31" deep x 12 3/4 inches tall, but you can build it as wide, deep or as tall as you need it.  When i was done putting it together.  I tested it by jumping up and down on it and I weigh 230 pounds.  So this thing is quite strong.  I finished it up by covering the edges where the plywood meet with Edge moulding and the bottom with baseboard to match my laundry room.  I used Behr premium plus ultra paint on most of it and, behr alkyd paint for the baseboards.  Gave the top a couple coats of General Finishes High Performance Polyurethane.  Which isnt neccessary but I opted to do so because of the weight of the washer and dryer and the General Finishes High performance dries harder than most other polys that I have used.  I only used it on the top though. 

Taking into account that I used the paint and baseboards left over from renovating my laundry room.  This project cost about 150 bucks.  200 if you have to purchase the paint and moulding.  Quite easy to do and though I made the cutes I needed with my table saw.  This can be done with a circular saw and a drill.  No exotic tools are needed.  Will post finished pictures when my washing machine and dryer are delivered on friday and they are sitting on top of the pedestal. 

Queen bed with shim head and foot boards

I built this for my son's bedroom, but modified it to fit our needs. It is 42" high, 38" wide, and 18" deep. I did a double thick top, which I love, and my Dad routed it for me. This piece is solid! I am very happy with the result! Sorry for the not so great cell phone pics!

My first build, a small side table for our newly decorated guest bedroom. Adapted from the Mini Farmhouse Bedside from Ana's website and the side table from her book.

The top and shelf were made from reclaimed oak panels from an old wardrobe.

I now have a second table and a farmhouse bed to make. I constructed without a Kreg jig but am thinking of buying one now to make construction cleaner.

I really loved the design of Mimi's Faux Mantle. But the wife wanted an electric fireplace for the living room, so after shopping around for them and not finding any that we liked. I suggested we use the Mimi's Faux Mantle design and custom it to fit an electric firebox. We order and firebox then followed the plans pretty close as you. Then finished it in a pure white with an espresso stain. This was our second wood project and had a great time working together on this project. We can't believe how it came out and are already planning more projects.

Great project for my first attempt at building a farmhouse table.  I adjusted the base to allow a chair to slide in at both ends.  Braced breadboards on each end with (3) 2x4.  Very strong and sturdy.  Decided not to use the lower base support to see how it held up and has been extremely stable.  My wife liked the open look so that's all I needed to hear.  Excellent plans, had fun and came out better than I anticipated!

We have not had a headboard for our king size bed since we bought it 5 years ago. We upgraded from a queen and just never bought one. Since moving into our new home I've been going for a rustic look in the home and I knew this headboard would be perfect. I did lower the height of the headboard to be 4.5' and for the back panels you still only have to get the 6 foot length for a king.

Anna White Beam Table with Benches 

This was a fun build. I used the HD Kreg Jig for the 4x4 beams and a standard Kreg Jig for the table. The bases were done with a white wash finish and the tops done with a few different stains to give it more of a barn look

My sister had all her jewelry on a jewelry tree and couldn't see all of what she has. So I had an excuse to make her something, yay
The front is glass but I don't recommend using glass unless you have the exact size. I broke the glass while cutting it so I had to get help from my neighbor the the art frame maker. I added felt to the bottom for random little things and screwed a dowel in for rings. We're gonna attach it to the wall someday when were up to it but for now it sits on her bedside table.

Great little project. Finished just in time for Thanksgiving.

Andy