Community Brag Posts

We modified this table to make it larger for our growing family. It measures 42" (10 inches larger than the original plan). We added 10 inches to the length of the 2X6's and added 5 2X2's to increase the width of the width of the table. We love the interest it added to the table. 3 coasts of minwax cherry and three coats of minwax helmsman poly.

I loved the look and design of Ana's Simple Bunk Bed but due to limited space in our home, needed a triple bunk bed. I wasn't interested in the hassle of a trundle so I decided to modify the simple bunk bed plan and make it a triple. I have to say, I was a little worried about how sturdy it would be but this plan is so solid with the 4x4 posts that there is no need to even even think about that for another second!
I changed the ladder so that it was attached to the side rails of the bunk bed as someone had posted they did earlier and decided to add another little ladder for the middle bunk so my little one wouldn't have to leap from the ladder to get into her bed. ;D

In order to do a triple in our home (with 8 ft. ceilings), I needed to bring the height down so I made the bottom bunk sit on the floor with the legs only being as long as the height of the headboard. I also made all the headboards and footboards only as tall as the footboards in Ana's original Simple Bunk Bed plans.

This was my first build and there are definitely things I would do differently to make this work better if I had it to do all over again. I would make the legs a little shorter on the 2nd and 3rd bunk so that there is more head room for the person on the top bunk.

All in all though, I had a great time building this and can't wait to try some more of Ana's plans!!!

My dad used the plans for the Simple Bed - twin size and built two. Then he took the headboards from both to build the bed for our daughter's room. It sets against a wall, so it looks like a daybed since both ends are the same height. She loves it! The other bed will have both foot boards and will be used in our son's room when he is old enough for a twin bed. Our daughter loves the bed and our son can't wait to get his....and we all love that Pap made it just for them! :)

We need bedroom furniture desperately! So, I decided, for my second build I would start in our bedroom! The dresser first, because I was going crazy without a place to put my clothes!

I needed some extra storage space and have always wanted a storage bench in this corner of my dining room. It took me a week to build from start to finish. I’ve never done any woodworking before, so this plan was good for me, as it was easy to follow with the color coding. The only thing that was “off plan” were the X’s on the face of the bench. I had some leftover 1x1 trim, from a handyman project a few years back, that I was happy to use up. It fit perfectly and I had just enough for all X’s. My biggest challenge with this project were the lids. They have a very minor bow, so one of the corners isn’t flush. But, it’s not enough to bother me or need to re-do the lid. All-in-all, I’m super happy with this banquette and may have caught the woodworking bug!

I made this for my sister the day before her house warming party. It was a pretty easy build. I used wood glue and 2" nails. Using a nail gun, this came together pretty quickly. I do wish that I had wide enough clamps to hold everything in place while it dried, because there were a few gaps due to some imperfect boards. I used 104" stud length boards, so I only need to purchase 7 instead of 9. this was enough to make the cuts for the top and both leg pieces from each board. the price was the same and we had limited space in our van for boards, so this was a better option for us. I used a sprayer hooked up to an air compressor to apply the stain and was able to get in between the slats fine with this method, brushing over it as I sprayed. Luckily I chose the same color as her deck not knowing, so it matches great. Now I need to make one for myself! :)

I was looking for a way to better organize my basement workshop. After looking at your Ultimate Workbench / Miter Station project, I became both inspired and motivated to organize my workshop bench equipment and power tools. I was tired of moving equipment around in my small shop area to use it and the amount of time required to clean up the saw dust during and after project work.

I modified your plans to allow me to incorporate the use of a solid maple shop table that I have had for over 30 years and provide a means to have my main benchtop equipment (miter saw, table saw, and drill press) be readily available for use. I substituted the 3/4 inch plywood top with a 3/4 melamine top with a popular edge trim to allow the workpieces to freely move through the miter saw, table saw and assembly stations. In addition, I added a removable miter saw fence using the Kreg Precision Trak system to facilitate miter saw work setup and to make multiple repeatable cuts. I made the fence easy to remove and store by using 5/16-16 inserts on both the work surfaces and on the he overhead material storage rack allowing full use of the workbench surface.

I also incorporated a separate rolling cart that served as an assembly table, table saw outfeed table, shop air compressor and pneumatic nail gun storage, router and router accessory storage and Kreg Cutting Guide Storage.

I wanted to have ready access to my cordless tools, so I built a separate wall mounted cabinet that holds my drills, impact tools and drill bits. Of course, that lead me to build a wall mounted battery charging station to consolidate and organize all the different battery chargers and spare batteries. Tried to make all things Easy to See, Easy to Get and Easy to Return.

Finally, I spent quite a bit of time researching how to design and add a dust collection system. I ultimately went with a simple, but effective system that incorporated the use of a Dust Deputy Pro, 14 Gallon Rigid Shop Vacuum, Powertec 2 1/2 inch Clear PVC tubing, Blast Gates, Flexible Hose along with Dust Rite Hose and adapters to connect my portable wood working tools. The dust collection components work work well together capturing about 85% of the generated saw dust, but I want to give a special shout out to Shop Nation which supplied a custom 3D printed dust collection adapter for my Hercules Miter saw. It is really amazing how much of saw dust generated by the miter saw is now being channeled directly to the dust collection system.

I now smile every time I enter my workshop :)

Had a horribly messy front entrance so really needed this shoe cabinet. It's dimensions suited my space better than an Ikea one, and accommodated more shoes. This being my first project, I am glad I started with this instead of a loft bed, since I made alot of mistakes (& corrections) along the way. Although some of the problems occurred because of pieces that ended up being convex. I chose to fill in the gap between the two boards on the front of each bin. It worked out really well.
Really love the Kreg Jig! So worth the investment.

Could not figure out how to properly use magnet catches. Did apply one to one side of the top drawer but it doesn't work too well--pulls the bin too far in. 

I worked on the benches and table for three weekends. All are finished in Ebony by Rustoleum. I used the non-Kreg plans for the benches and the updated Kreg jig plans for the table. I spent a lot of time at Home Depot selecting straight, flat boards for the table top. I literally dug through all of their 1 x 6's and laid them out on the floor in the store to find a good fit. I finished the benches with three coats of Minwax semi-gloss, and I finished the table with three coats of Minwax gloss. I prefer the higher gloss so I may put a coat of gloss on each bench so they all match. I also put some heavy duty furniture felt on all of the legs so they slide easily across the wood floor without scratching! I've been using a sad hand-me-down table and folding chairs for the past couple of years. I couldn't be more pleased with how this turned out.

I live in Alaska and the lumber for the benches cost about $35. The lumber for the table cost $65. I spent about another $100 on wood conditioner, stain, polyurethane, screws, sand paper and a brush. So all total, I have about $200 invested.

I made this using the $10 Cedar Tiered Flower Planter plans. Painted Red White and Blue with stars.