Community Brag Posts

I wanted to build a small shower bench. I used the Providence Bench Plans and just made it a bit smaller with a few adjustments. This bench is 35" long and 18" tall. I did not use the cross supports on the bottom because it was so short. Also, you will see that I turned the bottom stretcher and side supports flat/horizontal. I put the screws for the seat boards through the top down just because this was the easiest way for me to do it. The plans did not show in detail how to attach the seat boards from the underside. It just said "finally, the seat boards." I guess they probably used a pocket jig. I bought a pocket jig and used it in the couple of places, but this was my first time using it. I used brown, coated decking screws in the places I did not use the pocket screws. This was my first attempt at building anything and my first time to use a pocket jig. I used a natural wood stain and Behr Weather-Proofing since it will be in a wet area.

This bed was built using poplar, and pine wood. I used poplar for most of the stained pieces that are visible, and the stain is varathanes Early American. This is the fourth bed I’ve built with Ana’s Farmhouse Storage Bed plans, because it breaks down to four pieces, headboard, footboard and two side boxes, along with the drawers. This makes it easy to assemble on site.

My friend & I made this doll house for a Christmas present for my daughter.  The plans were easy to follow!

I put carpet on the top floor & then used contact paper that lookes like wood for the other flooring.

I made this simple Bunk bed shelf so all the stuff my son stored on the headboard, wouldn't keep falling off. It was easy to make and I painted it while working on another project. and I used spray paint to get the orange on a little easier!

Theses cabinets were built for a customer from plans they had found online. The hardware was ordered with the plans for an extra expense and the glass was made to order. Hope you enjoy them thanks for looking.

This was a great project to do. I have a family member that paid that full price for the real Pottery Barn piece. I then made this one and showed it to them. Ha!

I used Alder ply but because of the expense I only bought 1 sheet which will run $90-$105 from Menards or Home Depot. Other lumber yards ran up to $140. I got all the pieces out of 1 sheet except for the 2 adjustable shelves which I used birch ply. And you can't even tell. I was going to make my own jig but just bought the Kreg pocket mini jig. Invaluable! and about $20. I found the overall cost from the plans to be under reality. Acrylic, hardware, and hinges will run you $70-$80 easy. But I guess if you use cheap pine or something than maybe you can be close to the estimate. 

As queried by others, I too found the plans to specify how to attach the top. I used tiny "L" brackets around the underside perimeter and attached them with my screw gun to the frame (pic attached). For the doors, I didn't like the idea of just screwing the acrylic glass to the inside of the door so I routed the inside and attached some plastic tabs I found in the screen door section of HD to hold them in place. (pic attached). You could also use small mirror clips installed upside down.

I wrestled with the color choice for a long time but finally found the Minwax Gel Stain Mahogany (which is different than regular stain mahogany) to be the right color. After staining and a coat of sealer, I glazed, let dry, then sealed some more. Finished it off with some supa-fine steel wool and paste wax.

I love this piece now because I only glued certain pieces so that I can take it apart and put it back together as I am moving soon. (out of country). The European hinges were a bit of a pain to mess with since they have some movement to them and only lateral adjustments, no vertical. But it came out great. (I think)

Thanks so much for these plans!

$10 ledge and first build with a kreg jig!

Standard cedar deck, as you can see not complete, . However the benches are complete. Seen a picture in a book and custom cut and fit peices on my own

We are remodeling our 3 bedroom house into a 4 bedroom. In doing so, my youngest is getting the smaller room. We decided to go with a Murphy bed to allow more play time space. I do not particularly like the fact that this bed doesn’t sit off the ground but overall love the simplicity of making it. We turned it horizontal and just love the overall product. I can mot wait to make something else from this site!

Tams

We built three different sets of these ledges one set for each of the kids and one for our bedroom. We requested some sample paint off line in some colors we choose so the paint was free. Very simple to make and finish. We drilled holes 16 on center to hang them off the studs to allow heavier items down the road. Picked up the wood from the home store cut them down and sanded with 180 than 220 grit sandpaper then slapped on the paint.