Community Brag Posts

I wanted to start building right away....But had nowhere to build! Anna suggested the Kreg Jig, and since my birthday is when I found the site, "suggested" this as a gift to my daughter, who passed it on to the big guy...and viola, Master Kreg Jig. Happy Birthday to me! I got the plans from the Kreg Jig Community....super helpful site, answer all questions, and a great resource to beginner builders.
The worktop is made of 2 pieces of MDF, which is SUPER durable. Loved working with it. This took a day, and not a day goes by that I don't use or get some kind of compliment on it. What's really neat is there is a utube video to follow as you build geared towards the just starting out builder, which shows layout, cuts, jigging, very easy to follow. Plan is on Kreg Jig Community, free if you register, as well as lots of cool free plans....not quite as cool as Anna's :)
Very reasonably priced about $70 inc 100 ct Kreg screws

This is a wall ornament I made for my daughter for their get away home on the golf course at Canadian Lakes, MI. "No animals were hurt in the mounting of this moose head" The only thing to suffer was a few pieces of scrap wood that I had laying around.

This project evolved from us purchasing the wrong foam to go under 4 area rugs.  After it didn’t work for the first rug, we had 3 more rolls of the stuff that we couldn’t take back to the store (we had waited too long to do a return).  I originally had intended to buy an inexpensive sectional sofa for the downstairs family room, but with all this foam staring at me, I decided to put it to use and make sofa cushions.  There was enough foam to do a whole sectional!

The sofa frame is based on Ana’s Outdoor 2x4 Sectional sofa.  I adjusted the size, because the fabric I wanted to use was 54” wide, and that would fit nicely around a 22” deep x 4” thick cushion.  Each cushion is 11 layers of the foam (seat cushions: 67 x 22 x 4, backs: 67 x 18 x 4). That length for the cushions fit exactly into the 8 yards of fabric available on the bolt.  The next week I ended up going back for some more fabric for the corner cushion and an ottoman that's in work. 

I had the frame assembled and was ready to add the final upper back pieces, when Hubby suggested we give it a slanted back.  That required a little re-engineering and a couple of extra boards on the back and armless end.  Instead of using 2x4s the full length for the seat, I had used some 1x2 furring strips reclaimed from another project.  Also used some of those for the upright pieces for the backs.  Added some 1x6 to top the arms and ½ x 3 ½” craft boards to the front to hide the cut 2x4 ends.

The cushions are covered in a polyester faux tooled suede (fabric from Hobby Lobby).  The cushion covers are slightly loose on purpose, to give the nice worn squishy look that a real soft leather sofa cushion would have.

It’s surprisingly comfy and we love the look! 

I have a rustic outdoor room made out of our garage. We started the project last summer but it took until this weekend to get a table built. I was skeptical that I would be able to build a table myself, but I knew this table would fit in my backyard decor and I had to do it!

Using the plans from the site, I was able to build this almost entirely by myself. I got help for flipping it and adding the side aprons.

I started around noon with a trip to Lowe's and was done by about 7:30. The wood and screws cost around $50. I still have to finish it and am thinking of staining it dark brown.

Also, the guy at Lowe's recommended that I used deck screws. So that is what I used. I did not pre-drill all the holes. I also put the 2x6s in the table top, then flipped it over and added the 2x2 supports and screwed them in. I think that saved some time and seemed to work out okay.

Thanks for a great project, Ana! I am so proud of myself that I did this! Now I am off to make a bench to match.

Using Ana's great Reclaimed Soda Crate Caddy plan I built the perfect wood caddy for my bathroom by just adding rope handles and stenciling "BATH" to the front.

This was a fun and very rewarding project.  Thank you Ana for sharing your talent with us.  I got tired of stores wanting too much money for cheaply built bar stools, so I turned to the internet and found Ana.  These stools are quality built, and at a fraction of the cost.  The only thing I altered in Ana's original plan was the backrest.  I tried to build the horizontal braces but kept damaging the wood.  So I just built them vertically.

Picnic table is built of non treated pine. 2x6 and 2x4 only. I did stain as I went with outdoor stain just so everything would be protected. I don’t have the exact amount of wood bought but I think it is around 11 2x6 and 6 2x4. I used plans off of YouTube from A Simple Design of Ocalala. https://m.youtube.com/watch?v=WlprN_rUiJg

This was my first project that I took on from this site, and I was very happy with the result.

I used the plans from the Simple Sawhorse Table, and adjusted to our needs.

The only real adjustments were instead of using a solid top, I used 2 2x10's. I also made the total length 90" on top.

Very great site, and hope to be building more soon.

I made the $4 dollar chair and Ana Table. For the chairs I used 2x2's for the legs to help sturdy it up and because of that my seat slats are closer together. It's a very sturdy chair. I can sit on it and it doesn't budge.
The table was easy to do.

This was a project that took me about 4 weekends.  Last year I installed the French doors.  I decided that this was the year to finish them and the rest of my wife's office with a custom Wainscotting, based off the farmhouse style.  In order to keep it cheap, I used 4' x 8' sheets of 3/4" mdf.  I would then rip them to the width of my choosing, based upon design.  Overall, I used 4 4'x8' 1/4" plywood (for backing), I used 5 4'x8' 3/4" mdf... At a cost of $29/sheet. After installation, filling holes and seams, I primed then painted using a spray gun.  Total cost: about $350.  The room is much more rich, and really lightens up the space.  

Upcycle headboard bench made for a local fund raiser

I wanted a table like Ana's narrow cottage table, except I just wanted an open shelf instead of a drawer for a basket.

Here is my version modified to fit my needs. Thanks to Ana, of course. :)

This project is fun and relatively quick for the end result. All together, it took just over 20 hours. For the most part I followed the instructions and wood cuts according to the plan. I ended up having to tweak some things and I'm not sure if the error was in the plans provided online or my own error. Probably mine!

I thought I would add that, for the sign, I simply picked a font on the computer and printed out big letters (a size that would fit nicely on the sign) and then used those letters to trace out the border. Then I painted the letters by staying inside the lines! Easy Peasy. I used a small rustic rope and drilled holes in the sign to slip the rope through. I then tied knots so as to hold the sign in place. Works great and definitely completes the set. I thought about skipping the windows, but I'm so glad I did not. They really stand out and look amazing. My son loves to open them and just stare out (who knows what his imagination is making him see).

This bed is great because it allows for another area below. My son likes to turn on a lamp, sit in his chair and read. Thank you SO MUCH for this plan!!!

I found this fabulous vintage metal flat file cabinet at an antique store (Hunt & Gather Vintage Market, in Princeton, MA), but it didn't have a base or a top, so I went searching online for something that I could build.  The Corona Coffee Table plans were going to be perfect!  I just had to make a few adjustments:

1. Build it to fit my flat file cabinet.  
2. I didn't inset my apron 1x3 boards because I wanted the top ones to be flush with the edge of the flat file cabinet, and then I wanted the bottom ones to match.
3. There was a "lip" on the top of the flat file cabinet, so I had to build a thin trim around the bottom edge of the table-top.  This lip keeps the top from sliding off the flat file cabinet, but just to be sure there wasn't any wiggle, I put a bead of silicone around the top of the metal cabinet and then placed the wood top on.  

LOVE how this table turned out!  It's counter-height and the perfect centerpiece for my craft room.

Not much to say, just a quick project to use up some scrap lumber. Better to use it than burn it.