Community Brag Posts

My wife and I needed bar stools for the kitchen and could not find ones we liked. Also, finding ones that were the height we wanted was a challenge. So, after seeing the plans for the Simplest Stool we decided to make them. It was really quite simple with the plans given. Even the angle cuts were not that bad. Thanks for the plans for this awesome stool.

My patriotic pie safe

My entry into the IG Builders Challenge. Modified the Ana White Bailey Console a few ways. Instead of 2 large drawers, I installed 2 doors on each end, with 2 drawers in the middle. Century old barn wood used throughout. The legs are reclaimed oak floor joists, front stretchers are oak, rear stretchers are poplar. Heart pine planks users as door and drawers fronts. Heart pine front the same barn used as the top as well. Barnwood skins used on each end and the middle of the backside. Reclaimed shutters were used on the door compartment bottoms, and the rear.  I may eventually add a lower shelf with some of the leftover poplar and barnwood skins at a later date. 

 I had so nuch fun making this table. I love how it turned it out.

Mrs. Lasley

I combined my favorite elements from three of Ana's dollhouse plans to make this dollhouse for my kids. My favorite part is the stairs, which I cut from a 2x4 with a miter saw. I made this project from start to finish in one day while the grandparents took the kids, and it was ready for Christmas morning! I made simple furniture for it, too, which you can see in the second picture.

I fell in love with the Farmhouse Toddler bed, but decided to stray a little from the plan and made a couple changes. I chose to use 2x2 lumber for the legs and purchased mortise-free bedlocks from Lee Valley Tools so I could disassemble the bed to make moving it easier.

I lengthened the height of the headboard so it was flush with the bottom of the bed and also lowered the entire bed so it's only 4-1/2" off the ground.

Rather than attach the wood mattress slats, I cut and nailed small wood "spacers" that the slats sit between. This keeps the slats from shifting, but makes them quick and easy to remove to disassemble the bed.

I loved the look of the curved rails on the Lydia Toddler bed but extended them a bit further than the original plan.

The mattress we have was a different size than the orignal plan was based off, so I ended up using all 1x4 lumber and then just trimmed off about half an inch on each side before attaching to the legs with pocket hold screws.

I'm thrilled with this little bed and so far our daughter seems to enjoy it as well.

I started this project on my own never building anything before. It was so fun. My husband helped me get the roof on and the trim work.

Took 2 weekends to build 2 of them, they have a gently distressed finish.

With inspiration from Ana’s Little Crates, I prepared crates frames and slats separately so employees of a retiree may write on the slats. Once the writing was complete the slats were attached to the frames and presented as a personalized gift with examples of hanging or tabletop use.

Thanks

I started woodworking about 6 month ago and I love it! 

I made our kitchen table and nightstands.

This was a real test! The drawers took as long as the frame, if not longer.

It's all worth it when it turns out this good though!

Thank you for all the wonderful plans, my wife practially has all the furniture in our house in line to built by me. 

Built this for my daughter. Plans were excellent and I needed them because I am not an advanced woodworker. Going to try for a matching end table. If you have plans that would be greatly appreciated.

I loved the idea of the charging cubbies and the storage area in this plan!
I needed something a little shorter, for my three younger boys to be able to reach the hooks, though. I modified the plans a bit for this. I also opted out on the drawers and just left the cubbies open. With my boys, the more simple something is to use, the more likely they will make the effort ;)

I added a 2x4 to the back for hooks. I wanted the wall color to show through the back, so I didn't use a back piece.

My shelves are about 2.5 ft long. I wanted a display area in my dining room to show off some plates I had made for my boyfriend a while back.

I have a pet ferret that has little room to run around. So I seen this rabbit/ferret cage at the pet store. It was about $150 or so. So I took a pic of it on my phone, and found the Google Sketch app, and watched some videos, and now I have plans for the cage. Some 2x2's, 1x8's, plywood, chicken wire, and some locks and hinges for the ramp an lid.... Still tweaking it, but hopefully it will work out.

I loved the style of this desk but needed it to be quite a bit smaller. I reduced the measurements down from 48 inches wide to 28 inches wide. This required only 4 foot long 1x12. I added just one 15 inch wide faux drawer on the front. This was incredibly easy to build. It took me longer to paint and stain the timber than it did to build it.