Community Brag Posts

I built this indoor playhouse for my daughter who turned 2 in september. She loves to help mommy cook, loves to have little tea party's for her dolls and love to watch Chip n' Dale terriorize Donald Duck. So I thought I would give Alexandra her very own little house to do all those things. I hope you all like it and have just as much fun building one of these as I did. 

I have to shorten the design up a bit to fit my dinning room. I also did Epoxy Resin on top to give it the glass like appearance.

So ebony stain on white pedistole with an Epoxy Resin finish.

So excited!~ I've got big projects in mind but I just wanted to test it out first with a simple one. So easy to follow and I can't wait to do more!

Great project - fun to build and helpful for wheeling my new miter saw around the garage.

I made a few modifications from the original plan:
- I used a 1x4 instead of a 1x3 for the bottom supports to add a bit more of a lip to keep things from rolling off of the shelf. The shelf is big enough to hold my small pancake compressor and ciruclar saw.
- Like others, I added a drawer (1X4 front/sides, 1/4" plywood bottom, 2x2 drawer guides).
- Like others, I went with simple strap hinges and then used some wood to support the wings when open. When closed the supports tuck neatly under the wings.
- I added some 1/4" plywood to make a back. I left enough of a gap at the bottom to be able to sneak my extension cords out to a power strip I mounted on the back.
- I made a fence extension out of a 1x4. I attached this to the left wing using wing nuts and hanger bolts so it is easy to remove if I need to. I spent time measuring carefully to make sure it lined up exactly with the saw's fence. It is nice for supporting longer boards and keeping them straight.

I built this table using modified pocket hole plans and a mix of pine, spruce and cedar lumber.

When I laminated the boards together to the table top I also applied four culls to try to keep it flat as possible. When I removed the culls the boards weren't as even as I had wanted so I used a belt sander with a 120 grit to take out the high spots. I filled the knot holes with some 5 minute epoxy and I really liked the look. I would use decent epoxy if I do another large lamination of knottty wood as the $5 microtube I bought was thick and hand to work into the small voids around the knots. After the epoxy cured for 12 hours I gently used the belt sander gentle to remove the excess and then gave the entire table top a little 220 grit action. 

Used the farm house bed plans from here with a few modifications.  Instead of plywood for the headboard and footboard, I used tongue and grove 1x6 planks.  I used edge glued spruce planks from Lowes for the drawer fronts and I invested a bit more on the drawer slides and opted for the full opening type.  Also, rather than 3 large drawers on either side, I opted to put 2 smaller drawers in the center.  I felt the shallower drawers would be more useful for smaller items (socks and underwear).  I also used a 3/4" molding to hid the ends of the plywood drawer boxes.  The weathered finish was created using a video I found on YouTube (https://www.youtube.com/watch?v=k7Via9Lz4Pw).  My upgrades increased the overall price, but it was still under $600 and should last a lifetime.

My best friend (and upstairs apartment neighbor) was looking for a "grown up" bed for her apartment. When she saw the Swedish Bed, she fell in love. We built the frame out of 1×10′s and the “guts” were reclaimed wood from my Dad’s barn (to cut down on costs). She painted it a flat black using mistint paint pints from McCoy’s that were $1 each. The pipe legs were from Lowe’s in the plumbing section, and they’re threaded for easy installation. You just thread them into a little square base that you can screw straight into the wood, and pop on a threaded endcap so it doesn't scratch your floor or rip your carpet. Her first choice of 10" proved to be much too tall after she plopped on her enormously tall pillow-top mattress. So we exchanged them for the 6" version for a much more balanced look. She loves it!

I was looking for a long desk for two people and wasn't able to find anything that wasn't custom. I decided to try and here it is! I now have a massive and sturdy desk I can be proud of.

Not too bad of a project but had to a good bit of guess work so I could changed the plans for a queen size bed and flip in on its side.

Sister asked me to make her a table. Since I am out or work right now I said yes and got this thing done in about 3 days! 

Built this cute doll bed for a friend's daughter's 3rd bday. I hear she loves it :)

The bedding (which took the longest) was made from my stash, followed loosely the plans at
http://fromanigloo.blogspot.com/2010/11/dolly-bed-fitted-sheet.html

and http://fromanigloo.blogspot.com/2010/11/dolly-pillows-and-pillowcases.h…

I wish I had a nailer; this project would have been faster with that. Predrilling etc took more than I care.

Mostly used left over 1x3s, and the rest was brand new pine.

Note to self: don't sit in chair out back when you have a dog that likes to lick. This chair puts you right at licking height....

I also created a build video here: https://youtu.be/h_oEu908-iI

What a fast, fun, and FUNCTIONAL project!  I did lower the seat height, as I think it allows you to sink into them a bit more -- especially with the cushions I had for them (which BTW, were on sale at Lowe's for $14.99/each.. normally like $60, I think).  Thanks ANA, for making yet another project such a breeze!

I wanted a big rustic farm table, didn't want to drop thousands on one from a store, so I decided to make my own!

I built it in the (formerly empty) dining room, with tarp on the floor and plastic to seal the doorways.

Was a big project and my first project so I started with the benches as this site and users recommended.

I used the farm house bench plan - just shortened the dimensions so that I could have two benches on either side of the table. Then I merged the two table plans so that I could have the top with the bread boards but legs that attached underneath (like the rustic table) so that they could be removed when we move. I'll work to upload my plans too.

Used Minwax Wood Stain in "english chestnut" and Deft Satin Wood Brushing Lacquer (instead of a Polyurethane).

My first big project! Decided to make two cabinets and drawers to make the desk more symmetrical and a better fit to the room. Also decided to go without the knobs and bottom trim under the drawers so that I could just pull them out from the lip underneath. Just a personal preference for me.
I definitely had lots of fun building this desk!

I essentially followed the Rogue Engineer plans exactly with the exception of making the table on 50 inches long to help it fit better in my living space. I also opted to not add the lower support struts that would be perpendicular to the table top. I felt like that were bulky and were necessary for support. I may choose to go back and add them though. A miter saw and Kreg Jig are essential to get this project done with ease. I gave it a rough sanding to help keep the rugged texture of the original woodand maintain the reclaimed look. Feel free to post any questions.

Just finished this maple bookcase with fluted trim for my daughter's room.  I chose all maple trim even though it's painted because I wanted a good hardwood with low grain that would look good for decades to come.  Full build details are on my website.  Router bits used were a roman ogee and a core box bit.