Community Brag Posts

I wanted a good flat and level workspace to continue projects. This workbench folds up to the wall in my garage so I can still park when not working on anything. I made it pretty stout with 2x4s and 2x6s since it would need to support fairly large pieces of furniture without deflecting. It is very heavy as a result though (good core workout folding it up and down :) )

I used two folding shelf brackets on the legs to keep them from accidentally being kicked out from under the table while it's out. (http://www.woodcraft.com/Product/2001690/2615/Folding-Shelf-Bracket-8-P…)

I used four heavy strap hinges to connect the table to the 2x6 (which was lag screwed into studs). Two gate latches were used to secure the edge of the table to studs when the table is folded up.

I cut the legs approximately, and then when the table was hung I cut and shimmed them to get the table level on the uneven surface of the garage floor.

My wife was needing some extra storage in the garage for seasonal decor totes.

So, of course, I first go to Ana White's website. Voila, I found the perfect plans for the space I had to work with.

- The final product ended up being 72"Hx54"Lx21"W

- I used a counter sink bit to pre-drill screw holes so the heads would be slightly below the surface of the boards. This way the totes would not get caught on or damaged by the screws.

My wife has been looking for a jewelry cabinet at local antique markets so I decided to make her one for Christmas. I mostly followed the original plan but added cork in the bottom section so that she could push in earrings that can't be hung from the front.

Made the table runner from cherry for my wife for Christmas. We have lots of Department 56 pieces and no place to show them in our new and smaller home.

We were in desperate need of a lego storage solution for our son's small bedroom. I made this for his 7th birthday. I saw a photo of a similar one as a result of a google or pinterest search and decided to draw up some plans.
I recessed the top slightly so that pieces won't fall off. I just glued thin cleats to the inside of the box to hold the lid, (using spacers to get it at the height I wanted) Ideally the top would be reversible however I didn't quite get one of the dividers square so it only fits one way. I used Posca water-based markers to do the text. Make sure you wait until the text is really dry before you try to seal it (don't ask me how I know that...) Turns out that the markers don't react well with the brush on poly so I just left the text unsealed.
I was just going to have one handle on the front but then I made a stupid mistake and wrote the text so it would be upside down when pulled out (I know, dumb right!) So I added another handle on the other side. I used a water-based enamel for the whole box. Not sure if that was worth it of if I should have just used flat and given it a top coat of poly. I used a brush on the inside corners and found it really hard to get an even finish because I rolled the flat surfaces. Painting the pieces before assembly would probably fix this.
Added some castors so it can be pushed under the bed.

I built this project by myself.  My husband helped move the large pieces when I connected them, so one person really can tackle this project!   I had a combination of scrap wood from new home construction on hand and store bought lumber.  Most of my time was spent sanding, sanding, and more sanding, especially with the construciton grade lumber.  Yes, it was worth it!   I used tongue and groove wood for  upper level flooring and bridge.  It really made it easier to put the floors together.  I connected all the tongue and groove pieces with a snug fit and used my brad nailer to secure it down on the perimeter of the floor.   Therefore, not every peice had to be screwed down.

This was my first build.  After searching high and low for a desk for my husband for Christmas, I decided to build him one......2 weeks before Christmas.  With some help from my father, we somehow pulled it off! (without killing each other) I followed the plans exactly, except for one thing.  I used a pine panel for the top so my hubby would have a flat writing surface.  I purchased a 6ft panel (i think) and cut it down to 5ft.  When he went away on a business trip, I transported it from my parents house (where the build was taking place) and assembled it.  Then I put a big red bow on it and surprised him!  Don't know how I'm going to top that gift!  

Potting Bench Build! 🪴🛠️❤️
.
Another project I’d been working on 😍💪🏼 I love building things and woodworking. Been wanting to build a potting bench for a couple years now. Finally decided to do it. Found a little plan on Pinterest by Ana White, headed to Home Depot, and bought a bunch of 8ft 2x4s and 1x4s. Customized the plan by adding additional shelves, lattice-like backing, hooks, and knobs.
Had a bunch of leftover paint and stain, finished it off with a few coats of spar urethane. - Kendra

The cookie tray. I added two rows as we get a lot of treats gifted throughout the season. It is sitting on one of the buffets from the site as well. I cannot wait to try it everything in one spot and out of the way but easy to get into! - Danielle Arthur on Facebook

I used the easy frame and panel doors instructions to build 4 new large cabinet doors for my hallway cabinets!  I painted them Sherwin Williams Alabaster.  You can find my full blog post about them here:   http://www.leapoffaithcrafting.com/make-shaker-cabinet-doors/

I made this nightstand and one other from the Kentwood plans. The handles are diamond willow from Wisconsin. I used 1x2's for the door.

My garage needed an overhaul and I wanted to start a hobby in woodworking.
I found my way to Ana's website and found some of the best ideas and decided to try my attempt at building the Ultimate Roll Away Workbench with Miter Saw Stand.
This helped inspire me to augment my garage and build that workbench and new french cleat wall.

Thank you Ana for having such an awesome website and offering up ideas for free!!

My 13-year-old daughter asked me about making a stool, with the main requirement being it had to have a round seat.  So I turned to this ana-white.com to see if I could find something that we could do and found the plans for the three-legged stool. The first one we made with the dimensions specified in the plans but she thought it was too short.  So we made another one with longer legs and a larger diameter seat.

Seen a picture somewhere and I liked it . It was on my mind so I made this Nativity Manger, no plans just went for it by memory.