Community Brag Posts

I followed the plans exactly, and added the headboard at my daughter's request. My brother recently tore down an old fence, and I pulled this gate out from under a brush pile. I strengthened it with lots of screws and cut each side to bring it down to the same width as the bed. The whole project cost me somewhere around $150-160 because I literally had nothing but a drill. I had to buy everything from screws to nails to wood conditioner, etc. Not bad for a truly "from-scratch" project.

This was my second-built project after finding Ana's wonderful site - the first being the Rustic-X coffee table.  After learning how to use a miter saw, jig saw and kreg pocket hole jig for the first time by watching Ana's video tutorials as well as several others available on the web, I built up the confidence to attempt a media console for my three video-gaming boys. 

I pieced together a design plan for the console using the general design of Ana's Apothecary Console Plan, together with the incredibly helpful plans and instructions detailed on 2Crafty4myskirt.blogspot.com.  Kind of like mixing together pieces of different recipes, I was able to create a design that had the length of Ana's console, plus 2Crafty's wonderfull side-storage doors for all of the boy's video games.

As set forth in detail below, I used Ralph Lauren's Carbon paint for the entire unit, and Minwax Red Chesnut Wood finish to distress the edges.  I used Pecan Minwax Polyshades Stain & Polurethane for the table top.  One of the most helpful pieces of advice from 2Crafty was to leave attachment of the back and top of the unit until they are separately painted and stained.

I finished the false fronts with antique copper (bronze) cabinet label holders (2 1/2") which I purchased online at D. Lawless Hardware online.

As a beginner, I had a steep learning curve in learning how the tools worked (safely), and so it took me about 40 hours all in to finish the project.  While my sons helped along the way, my husband didn't actually set eyes on the project until it was complete.   He was stunned at how beautiful it was - and that I had in fact created what he calls the "center-piece" of our family room from a pile of lumber purchased at Home Depot.  He is full of helpful suggestions of what I should make next!

Thank you Ana for providing me with the tools, skills and confidence to produce a piece of furniture that I am very proud to point to and say "I did that!"

We were given this fireplace insert and need something to house it. After searching the web, we decided that Ana's faux fireplace design was our best option. We modified the measurements to fit our needs and added a wood stained top to serve as our "mantle". We are thrilled with how it turned it!

Ana's $10 ledges. In Colorado, they cost just a couple bucks more at $13. Thank you, Ana, for helping me see just how easy these shelfs really are!

This is a miniature version of the Man Crate, measuring 6” x 6” x 4 ¾” tall, made from 1/2" and 1/4" scrap birch plywood, with added hinges to make a lift-up top. 

This is going to be a gift - - I’m going to send it filled with candy.  

The girls and I are all in! We just started our build for the Playhouse Loft Bed. Wish us luck!

AlphaPilot

Reclaimed wood desk top for a Geek Desk stand.

Needed a small table for the nursery and this was perfect! 

I zigzag stitched vintage neckties to plain canvas and used these directions to construct the stool frame. I used 1 5/8" screws.

Based this wagon on plans found on Ana White's site. I built this for a 2 year old girl of a co-worker. She is right now using it to pull around her dolls.

Sliding barn door tv console. Created the metal hardware from aluminum i bought from home depot ($80)

This was pretty easy and inexpensive to make.  I'm going to make the coffee table this weekend, but converting it to a chest with a lift top.  Purchased some cantilever hinges for that on Amazon for about $35.  Will post pics of that once it's done.  Sorry the photos came out sideways....They keep uploading that way even though they are right side up on my iPad......

I was told about the site from my neighbor. Little did I know I would find myself wanting to build everything on this site. So I started with the 6 cube bookshelf leaving out the dividers on top to allow the kids to use it as a bookshelf. I also wanted them to have a place to store their dress up clothes when they weren't in them. So, I turned the 6 cube bookshelf on its side and added a couple of inches to allow for small dress up outfits. I am going to put the storage bins in the squares once I find some.

I followed the plan for making the shell of the house, but since I have access to help and the on-post woodshop I made a few changes.  We cut a 2x4 to fit the doorway, and then used the lazer cutter to make the panels, after sanding and painting, I used a necklace bead as the doorknob.  We also cut some 1" square blocks and drilled the center, the used the grinder to round them out to make a holder for the dowl curtain rod.  I also used scrap frame wood for the window/door trim.  Then I covered the entire house in wallpaper!  The outside is a brick wallpaper, the inside is a gray/silver with sparkles, and the ceiling is white with sparkles.  I used cork for the floor so it would be soft and warm feeling.  It took me a long time, but I am very happy with the results.  My daughter was thrilled to recieve this on Christmas morning!  

Built a pair of these for the master bedroom as my first project... Not too bad, very functional, and I was able to use mostly wood I had laying around...

This build has been (thus far) my biggest and most ambitious yet. This is not only for the size of the build but the techniques I used. While I did use pocket holes in many spots I changed the design by using two stretchers to span between the sides and provide support for both side walls and bed slats. To reduce the number of pocket holes the original plan called for I used my stacked dado kit and created to dado cuts in the stretchers to support the bed slats and side walls.

But I can't say enough good things about Ana and this site. The original plans where a inspiration to build this bed and continue to inspire me to build other projects around the house. All of our friends who have seen pictures of our Sons Ski Patrol Shack bed have raved about it and I can even see a little pride in my sons face when other kids are ranting about how "cool" his bed is.

So while I didn't follow the plans exactly the end result can't be disputed; its an awesome feeling to give your child such a great bed! My son came up to me and hugged me and said he loved his bed. So from a plan I downloaded to that moment of my son telling me he loved it was all worth the effort!! Thank you Ana for posting this and all the other plans. They are not just building plans to download they are happy memories waiting to be built!! Cheers from Colorado!

We made this bed in the king size. DEFINITELY sand each shim prior to gluing it down. It is definitely no fun rolling over in the night and hurting my hand on the rough shims. I would also recommend staining the headboard (the base for the shims) prior to gluing down shims so that any holes between shims blend in with the stain color underneath. We did not and there are a couple spots that you can see the plain wood under the shims. Also, we did what they recommended in the plans to secure the side rails. The bed is not very stable and squeaks. We keep talking about altering it somewhat, but it's so dang heavy that we have been putting it off. One other thing that I wish we had done would have been to sand off the corners of the end of the footboard. We've gotten a few bruises from walking into the ends. It cost more than we expected and it took longer. But overall, we love it and are very happy with it. Just wish we had known now to do some things differently.