Community Brag Posts

I have wanted to build this bed for a very long time. I finally bit the bullet, stopped procrastinating and just got on with it and thank god I did. It was actually easier than I thought. It just about built itself! I built this bed taller than the plans called for. I used joist hangers to support the mattress beams. The joist hangers were attached to the inside of the siderails and the mattress beams just slot into them for easy removal. The most time consuming part about this build was the painting. It is extremely sturdy. This bed will last a life time.

Made for my daughter for christmas. hope she likes it 

I loved the idea of a loft bed for my daughter to maximize space, but wanted more farm house style. So, I made a few modifications and it turned out better that I ever could have imagined. Raising it up just a bit more allowed for a custom desk build for underneath as well. - Anna

12/16/14 UPDATE:  Posted a plan for this project, linked in this brag post

This is a variation of the Easy Jewelry Box plan. The completed measurement is 11” wide, 14 ½” high, and 7 ½” deep. This one has a center “tower” with 5 drawers 5 ½” wide, and a wide overhang on the top and bottom, which covers the 2 side doors that open out for hanging necklaces. The drawers are lined with embossed felt, and the drawer bottoms and insides of doors are covered with sticky-back felt. The 2 removable ring drawer inserts are some scraps of 1” foam, covered with scraps of the sticky-back felt, with slits cut into the foam with a utility knife (cut the slits into the felt first, attach it to the foam, then cut the slits into the foam). Cost breakdown: antique brass knobs: $28, sticky back & embossed felt: $14, hooks: $15, wood: $35, hinges: $7, paint: $5. (already on hand: finish nails, glue, sandpaper, left over stain & poly) . I worked on this a few hours a day over a long weekend, probably about 12 hours total. Finishing took most of this time, the build was actually only a couple of hours.

I needed to build a bedside table to go with my farmhouse bed and I wanted to make one that was not matchy matchy with my other one and it also needed to look a little more manly.

I used new chunky pine for this build.

I couldn't find the right handle for this so I bought a steel strip from Bunnings and bent it into shape and drilled holes to attach it to the drawer. I bashed the steel strip with a hammer to make it look more rustic and battered.

The bolts on the legs are purely for decoration.

I think I managed to make a manly looking bedside table and it goes really well with my farmhouse bed and bedside table.

This was my first attempt to build a table . I'm very pleased with the outcome. 

Wide 7 drawer dresser made from Pine.

We have been doing some work in our garage and the old workbench had to be dismantled. My husband asked for a new workbench for father's day, but I didn't like any of the ones we saw at the stores. I told my husband that I could build a better one for cheaper and he said ok (although I don't think he really had much faith in it turning out). We bought the wood and then, after putting the baby down for a nap, knocked this thing out in 2 or 3 hours. It was very easy, just straight cuts and screwing the pieces together. I did the whole thing myself with a little help from my brother at the end. My husband loved it and showed off pictures of his Father's Day present to his boss and co-workers. We probably spent about $60 in materials and it really did just take a few hours. I changed the dimensions to fit our space and needs. We had some extra wood left over so we added a back-stop to the top to keep things from rolling off the back and I made the bottom shelf deeper. It was a fun and easy project to do.

For my third project I built my brother-in-law the Fancy X Farmhouse table cut down to a size suitable for him and his girlfriend. When I read through the comments it seemed like alot of people had the same question: How do I attach the top?!?!?! As this was going to be used for an indoor dining table I didnt want to screw through the top if I didnt have to and I didnt want to use metal bracketry eithery. What I did required 4 inch screws and  a 5/8 drill bit. Ive attached pictures to show where I placed the wood suport pieces. Two screws went through the top cross beam (connecting the two leg ends) into the center support piece and I put a total of 2 screws each through the sides of the two longer support pieces and into the top board of the legs. I used a 5/8 bit to drill about an inch (very rough estimate and essentially to countersink the screws an inch deep) into the 3.5 inch width of the 2x4s and then a smaller drill to pre-drill holes for the 4 inch screws. This allowed the head of the screws to sit about an inch into the wood and the threaded portion of the screw to dig deep enough into the second board without going through it. Overall it holds great and there are no visible screw heads on the top of the table!

FYI This technique DOES require aligning the cross beam with the top of the second 2x4 rather than the top 2x4  because you want to save enoughg room the support pieces. (See pictures)

King size Farmhouse Bed. With the Addison of 2 Morkies, we found real estate was limited on our old Queen bed. I took on your plan for the King Farmhouse Bed. With basic lumber (quality which leaves a lot to be desired), a lot of sanding, pocket screw joinery and a dark walnut stain; I am happy with the outcome. Thank for your plans. Keep them coming.

Our new outdoor coffee table

Rustic coffee table. Plans by Ana White. Coffee, vinegar, steel wool stain

My nephew and I made this bench for his mom and dad's 24th Anniversary

My first build! Came out great, my daughter loves it!

Farmhouse coffee table with Red Mahogany stain. Pocket holed so no screws show. - Roger

I used Ana's Queen size Farmhouse bed with the modifications for the box spring. I also changed the plans slightly, instead of the 1" x4" on the footboard and head board I used 2" x 6" at the bottom. I don't have a nail gun or finishing nails so this provided the stability and saved me a few dollars. I also made the corner posts longer than the plans to make the bed taller.

I love this bed, I made it extra tall, so you have to jump into it. And there is plenty of storage underneath!

It took me and my dad about 4 hours of actual cutting and assembling, but an additional 10-20 hours of sanding and painting. It took me a few months to actually finish it after work.

THANK YOU ANA for the plans!!!