Community Brag Posts

This tv stand was my second project I made. It wasn't too difficult, but I'm definitely glad it's done and I can reclaim my kitchen counter!!
I designed this myself, gathering ideas here and there from different stands I saw. The tv stand I really wanted was this one from Wisteria.com. http://www.wisteria.com/Recycled-Pine-Console/productinfo/W4180/ I've been wanting it for years, and it was about $1200. So that's where I got the idea for the slatted shelves, and the industrial wheels.
The hardest part were the "x's" on the sides, and finishing it, getting in every nook and cranny. Not sure how I feel about the finish, so I'm going to live with it for awhile.
NOTE* Casters were bought BRAND NEW a week ago on amazon.com. I soaked them in muriatic acid for 24 hours, and then dipped them in baking soda and rinsed. Then I did minor touches with a propane torch. Didn't turn out how I expected, but I like how they turned out. PLEASE do your homework on muriatic acid before using it!!
The corner brackets on the top were found on wildwesthardware.com.
The lumber for this project was only about $80. But the corner brackets were $17 each (they are hand forged) and the wheels were $100 for the 4, (after shipping). Still better than $1200!!!
**On the 2nd and 3rd pic, the steel wool juice hasn't dried completely, that's why it looks splotchy.**

This is by far the biggest project I've completed yet. It actually surprised me how easy it was to complete. It did take me about 4 days to build the project and an additional week to sand and paint the project.

I followed the playhouse loft plans and the storage stairs plans, adjusting only the back to allow for the additional length of the slide. I didn't add the windows to the sides (I didn't see any point in having them there). I also used the castle loft plans for the slide. When I first started this project I was planning on making the slide completely separate. I changed my mind mid project after I had the side wall cut to length at Lowe's, so I just added that small piece to the left of the slide to make up for the gap. I also made this project in 4 separate pieces (stairs, slide, front wall, back) so I could put it together in her room in one evening and not have to kick her out. Once we moved it to her room all I had to do was screw the four corners in and attach the back wall and bed slats.

I definitely recommend not using particle board. I had no idea what the difference was between particle board, mdf and plywood when I started this project. Particle board was less then half the cost of plywood, but looking back I would pay the extra for the plywood. I don't feel like the screws hold well in the particle board and it also chipped on the bottom some. I actually had a chunk come off in the corner where I must of screwed to closely to the edge. I'm sure this is basic knowledge for most, but for those newbies (like me) just a little tip.

I had a lot of fun building this bed (not so much sanding and painting) and learned a lot. Now off to browse for my next project :)

After building and hanging a barn door, I realized I did NOT want to do that on a piece of furniture. It looks cool, but getting it to work right wasn't worth it. 

I altered the dimensions a bit to 25"H x 16"W x 61" L

I also used 1x3's instead of 1x4's since I was doing a smaller scale

cube bookshelves modified to have one open shelf and 3 cube slots

Easy excellent project for That odd room you may have that needs a corner tv stand.

I use pre made 16" wide 3/4" MDF shelving from Home Depot for the Shelves, Used 1" x 3" for the top, and sprayed it all with Rustoleum Industrial flat black which dries in 15min, was the large size cans for $5.40 and and only useds 3.25 cans to paint the whole thing. 

TV is a 55" Class so it actually works perfect, because the tv stand is two legs and not the typical center mounted ones. so  put the tv toward the front of the console and the console is as far as you can go into the corner.

I have two power strips screwed to the back of the console, along with a cable amplifier, my wireless router for the house sits right behind the TV and you can see the blue status lights under the bottom of the TV.

Have  my speaker bar in the added shelf #1 below the tv, comcast cable modem in the right side square, TIVO in the center top, DVD Player in the center bottom, and loads of extra shelf space for whatever else I can think of....

It was time for Addison to get a big girl bed. We used the Kentwood design and the trundle bed plans. 

Very easy to make, and not too expensive. I'm not that great with a lathe. I tried it a couple times but not too good. So I buy my table legs online through osborne wood company. These legs however, came from an old table that I got for free from an antique store. The rest of the table got cut up and used for 2 night stands, and this is what I used the legs for. I used pocket holes to attach everything. Support the middle with cross supports and there you have it. The benches are just 1x12x8's cut into shape and supported by 2 1x4's on either side.

This project was on the honey-do list. My wife was looking for antiques and had a pretty specific look she wanted this one fit. It was a fun and relatively fast build. I choose Oak as that is the most regular wood I use and had some on hand.

I modified the dimensions a bit making the hutch a foot taller and the buffet a little larger in width and smaller in depth. I used full extension ball bearing drawer slides for the drawers.

I rabbeted the back in and put a middle brace in for support and so that I could hide the back seam. I don't like to face nail face frames, but for this it turned out pretty nice nonetheless.

My dad and I built this table for my wife's birthday present. 

I followed plans from Woodworking for Mere Mortals. Steve Ramsey has a great build video for the project. You can check out the video on his YouTube channel. This lumber cart replaces a previous one that I built a few years ago. My old lumber rack could not store sheet goods and took up too much floor space in my garage.  I disassembled the 2x4s from it and hope to recycle them for a future shop project.

For complete build details continue reading my DIY blog here.

This was my very first "Ana project"! It was a special Christmas treat for my boys and their expanding train collection. This table has had many, many hours of entertainment and enjoyment. It is a great beginner project and has very easy plans to follow! I didn't do the storage carts at the time. I may go back and do them later though...for now they like playing under the table as well. My obsession began :)

This wasn't my first build job, but it was the first one where I needed an extra pair of hands. My daughter loves it and so does everyone I know! Thank you for the plans!

I needed to adjust the width of the dresser to fit  - and it was may first build by myself... Already have a second one ready to paint!
 

When I saw this table I knew it would be perfect for this space! I was so excited I copied "Sweet T" Table and added a faux handle (which is now my husband's new favorite word) I primed and painted it and then put a coat of poly on it. Was a fun project

This project was a whole lot easier than it looked I think that it took me three days from wood in the back of my truck to the finished project. I think that I spent about $200 on this whole bed and headboard. It is sturdy and I really love it.

Man cave chair for my Hubby, made entirely from reclaimed/scrap wood.  This took a long weekend to build (includes time to rip down the reclaimed wood, and a couple of tries to get the padded arm rests right). 

This build uses the Simple White Outdoor Chair plan, adjusted to fit smaller cushions and use my scrap/reclaimed wood. 

The seat cushion is covered with marine vinyl, and the back cushion is covered with fabric from a curtain already on hand.  The covers are done in a simple box style.  The seat cushion closes with ties at the back, and the back cushion has an envelope back.  

The end result is a sturdy, comfortable chair that’s not too heavy, and is decked out with colors from Hubby’s favorite football team.  I’m very pleased to say that Hubby likes his new chair!

Got this wood from some thick old flooring we laid in a house and brought them to my shop. Cost me about 20-25 dollars for lumber and paint. Everything else I pretty much had on hand. But man I think it turned out really well