Community Brag Posts

I altered the plans to the full-sized slipper chair so that I can document my upholstering process. SUPER easy, SUPER cute build (and my daughter loves it, so even if it weren't easy, it'd have been worth it :-))

I made this table and bench for my wife, for Christmas. She loves it.

This was a fun project to build! The plans were very easy to follow and the table and chairs turned out just like they were supposed to. I ended up buying a Kreg jig to put the furniture together. The jig cost $40.00 at Home Depot and it was well worth it because I'll be able to use it on other projects. The plans showed the furniture being prepped and painted but my daughter wanted the pieces to look close to their dining room table so I took the time to stain and varnish them. I built the table and chairs out of pine and I used average dimensional lumber so the whole project only cost around $35.00. If you're looking for good children's furniture these would be good to build.

built from Ana White plans for my son and daughter in law

Our "home made" bed. We made this bed from discarded cedar posts found on the property. Three of the main bed posts were the original entry gate posts at The Bed Rox and the one closest in the foreground used to stand where the cabin stands now.

This is our third project. We needed a table set in the living room since our IKEA coffee table did not survive the move to TX. My husband and I fell in love with the rustic X collection and decided to start with the coffee table first. Everything was quite straight forward until cutting the 2x2 for the X. Well, without much wood-working experience, I made a rookie mistake of cutting them to length before cutting the angles. Eventually, we came up inches short on the 2x2 bars to make a complete X. We had to re-measure and re-cut all the angled bars. But we made it! At first, my husband got frustrated and wanted to leave the X's out and let the table be open on all four sides. But since we are trying to build a whole collection (end tables next, and then console able), I really wanted the X's to make them cohesive. So we survived the taunting tasks and have learned from the experience. We cut the 2x2 a little long and then mark them against the frame before we cut. The original measurements from the plan did not really match up to our frame so we decided to mark and fine-adjust. It worked out well. There was a slight "rainbow curve" in the middle plank of the table top. We decided to use a heavy duty 2 1/2 PH screw on the sides to suck it in, to try to make it level. It worked out well too! At the end, we sanded all the corners and tops really well because I wanted an even top. It is a very nice size coffee table and heavy and sturdy. And we are both extremely happy with the final product.

$

This little nightstand holds tons of stuff.

We adopted two puppies: Blueberry and Pink, and needed a dog house. I showed my bf the post of the East Fork Dog House on this website for inspiration. He winged the basic construction as he's a carpenter guy. Our foster children helped paint it, and the puppies love it (chewed the corners of it already).

All hand cut accept for runner are attached with biscuits

This was a fun little project. I made the bench to be placed in our foyer to sit down and put your shoes on and off. 3” foam and fabric makes for a comfy bench.

This is Ana's king sized farmhouse bed with an arch. This turned out great and is super strong...much better than most store bought pieces. The "king" cat thinks its pretty cool too.

We made these last year, and managed to find cushions at walmart- but I never loved them. This year I painted the pieces black, added an extra horizontal slat in the backs, and recovered the walmart cushions and added some from ikea.

This is a fantastic place to check my email in the morning and read in the afternoon.

Thanks!

Faux fireplace 

We followed the plans except added in bed rail brackets to make it easier to relocate and adjusted the bed as a whole to sit higher off the ground. 

I built this for my daughter's room one Saturday afternoon. She even helped me sand and paint it! Its perfect for little ones who love to read. Keeps the books from spilling over the floor when we're looking for her favorites at night.

There was a cute little niche in the guest room my son and daughter-in-law stay in, probably designed for a dresser. With the addition of grandkids to our lives, I knew what they really needed was a changing table. On a trip to a popular home decor store, I saw a HUGE pile of lumber and shelves in a pile in the parking lot. I asked to see the manager who told me it was all being hauled away TO THE DUMP the following morning! I asked if I could take some off of her hands, and she said I could have all I wanted (a woodworker's dream come true!) I quickly put the seats down in my Pryus and stacked it to the ceiling! 3 trips later, and I managed to gather enough wood to make this project and many others, all for FREE! It's all 3/4" birch plywood. Most has deep scratches, probably from being thrown in a pile in the parking lot. Some of the scratches are too deep to sand (because of the birch veneer) so that is why I painted the top, sides and doors.

This was my first time making a drawer and these type of hinges. I also made the hardware and the legs. I love mid-century modern, so used a 1 X 4 and cut/sanded down a 1 X 1 at an angle for the legs (ok, honesty time, this was my 5th attempt! It took me awhile to figure out how to get the angle just right and make sure it was sturdy enough).

A big THANK YOU to my new KREG JIG, which I learned about in Ana's book. Without it, I couldn't have done this project!