Community Brag Posts

Followed the new home depot plans, only change I made was using 2x4 instead of 2x2. Getting ready to build another one, but this time will also change the arms to be wider on the ends to accommodate wine holder on one arm and cup holder on other arm. :0)

It was a bit tricky putting it together in my limited space closet but I got it all done! Loving it! It also forces me to make up a capsule wardrobe and clean out my closet as there isn't room for everything. Thanks Ana!

This was a very easy project from scrap wood I had leftover from previous projects. I modified the box a little. I cut slits in the box so the top slides on nicely. I also stained the box and sealed because I love the look of stained wood. I used early American wood stain.

This was my first project. We are using it in the Man Cave.

I scaled down the large rustic x bench plans to create seating for my grandkids at the new kid's table.

It took about 7 hours to complete this project. We used Ana White's Farmhouse Queen plans, with some modifications: the bottom of her bed frame is about 4-6 inches off the floor, ours is 17 inches for extra storage space. We also made the footboard slightly deeper to accommodate longer legs. Due to limited space, we built it on the bed of our truck with the "help" of our 18 month old. We love the way it turned out.

I only recently stumbled upon Ana-white.com and was amazed by all of the wonderful plans and tips here, not to mention the community. My wife and I had inherited a king size bed after my grandparents passed away. While we were both grateful, the bed was on a very basic metal frame that sat very low to the ground and was hard to get up out of. My wife had often talked of having a nicer bed to put our mattress and box spring on, So with great eagerness I set to work. I loved the classic look of this bed and was a bit saddened that there was no king-size plans available. I decided that wasn't going to deter me, so I set out to modify the plan to fit. After making a few adjustments and modifications, the bed really started to take shape. Needless to say, I am very pleased with the results! Thanks everyone, and thank you , Anna!

Modified the Camp Loft bed with Stairs plans slightly so that the dresser would fit under the bed without banging your head for access.  The heght is taller creating the need for railings to be added to the platform.  Conversion to bunk beds was considered so all bottom boards save the front rail were installed.  If bunk beds are needed, just add the 2x6 front rail.  The mortise slot is already cut.  Went with mortise and tenon joints instead of pocket screws.  Cubby storage area created under the platform accessed from left side.

Friends of mine are having a girl and needed a bookshelf for the nursery. Loved the simplicity of this design and wanted to see in an antique white finish. Great plans and design.

When we started building this bed, we liked that it wasn't too tall for our low ceilings, but could still utilize the space beneath it. As we were building it, we thought we would just put a 2nd mattress on the floor, but when we measured it, we decided we could safely turn it into a bunk bed for our 2 youngest daughters. We just built an additional set of rails. Instead of buying another piece of wood for the mattress support, we used the support from an ikea bed that we weren't using. We put the bottom mattress off the ground around 10 inches.

This took about 6 hours from beginning to end, but next bench should take about 4-5 hours. Most of the time was spent on sanding the wood and waiting for the stain to dry.

Main lesson learned: Drill pilot holes throughout. I used no-drill construction screws, but it didn't pull the wood tight enough against each other. Also, stain all the wood pieces before assembling (as opposed to just the top slats as suggested in the plan). Remember that the leg pieces will not need stain on the flat surfaces, just the sides that will be exposed. Use a square tool to stay as close to 90 degrees as possible.

I loved the original design but wanted to learn new skills and use hardwood.

I used a combination of pocket holes, biscuits to align the plates and the frames, and figure 8 fasteners to attach the top.

At a VERY low pace (~1-2 hours every day), and many mistakes, it took me about two months to complete this project. If I had to do it again, it would probably take me two-three weeks at the same pace.

Overall, I learned a lot and am very pleased with the final results.