Community Brag Posts

Combined the modular office small desktop with the Narrow file drawer base unit to suit my needs/space requirements. Used the legs from the narrow farmhouse table because I just loved them! Added beadboard for the drawer faces because it matches the rest of our house.

Converted an ordinary bathroom vanity into a Napoleon sink console/vanity. This is the second one I’ve completed, the first was in the hall bathroom which Hubby calls “his” bathroom. Since this one for the master bath is more feminine, I’m calling her Josephine! This was approximately a day and a half project, but spread out over several weekends. I had originally planned to put a faux drawer in front of the sink, and had the drawer front made, but then decided I’d like to try to make some custom drawers in front of the sink to utilize that space. I ended up doing the center drawer fronts twice – on the first try the space in the center was a little too narrow for the knob once the trim was in place. Since the vanity is in a corner, the sink doesn’t fall exactly in the center of the vanity cabinet, leaving it left of center by about an inch. This required different middle drawer sizes with interesting shapes.

The drawers are made from a combination of 3/8” craft boards and 3/8” plywood, ½” craft board, and some ¼” plywood for the bottoms (all of them except the one right of center – that has ¾” plywood for the bottom). The 2 outer drawers also have ¾” S4S as guides.

The doors and drawer fronts are ¼” birch plywood cut to size, with ½” x 1 ½” craft boards glued to the fronts for rails and stiles (I added a few pin nails from the back side also). Inside these, mitered pieces of mini-stop moulding were glued in place. The whole thing received some putty on the edges and joints, and thorough sanding with 80-grit, then 220-grit.

The inside frames are made from S4S, 1x2, and some scraps of 1x4 cut to size. If I were doing this in a newly constructed vanity without the sink already in place, the setup for the drawers would have been much simpler. But, we weren’t ready to buy new yet, so necessity was the mother of invention and we have this. I re-used the hinges and 2 of the knobs from the original, and I bought 4 more and the hardware for the drawers.

The pull-outs in the bottom are made from plywood scraps, thoroughly sanded and painted. These are based on Ana’s wood pull out cabinet drawer organizer, with added supports across the bottom to make the drawer clear the lip of the face frame, keeping them the correct distance apart, and giving something to attach to the cabinet floor.

For the inside floor of the cabinet, I got this Idea from Yvonne at Sunnyside Up-Stairs in this post:
http://sunnysideup-stairs.blogspot.com/2013/06/progress-installed-dishw…
Left over flooring was placed on the cabinet floor to give it a fresh new look and protect the cabinet bottom. Our house is 21 years old, so you can imagine the floor of the vanity cabinet had seen some wear and tear. Now it looks new!

I build this last minute for my daughters room makeover.  I worked through the night, but got it completed and painted just after sunrise. (I slept good the following night!)

I had made the farmhouse bed from Ana a while ago and finally got around to building a pair of these bedside tables to match. I love how much bigger the top is than my previous nightstand's top. The bins on the bottom shelf are relatively cheap from Walmart, and I like the galvanized look with the wood. 

My first non-home-repair project. Made three of the sling chairs for my kids. They each picked out their own fabric (regular fabric). We still have not sanded, filled and painted but are hoping to do so this weekend. The kids were very excited to have them. I have been reading your website for months now wishing I had time to make something, and these chairs fit the bill. Thank you!

I built matching side tables using Ana's Narrow Cottage End Table plan. I changed the height to suit the arms of my furniture. They fit our tight space and look fantastic with our existing wood pieces. Very easy to build, even the drawers! I used a router to finish the edge on the drawers, to make them stand out a little more. I learned to put my pocket holes on the outside of the drawer, since the back one is in the back, and the front one is covered by the separate drawer front piece. A Kreg jig makes this a very simple project. Also, I sanded my boards before assembly, then did touch-ups before finishing the project.

I built this for the three little ones to get ready for school and have a place to hang their backpacks.

After making the sling chairs, I decided to give the Farmhouse twin bed a whirl for my daughter. I absolutely love it! It ended up costing us $225 for all of the supplies needed. The only issue we had in making this was trying to make it easy to disassemble. This was fun to make!

My first project! The legs are shorter than in the plans-my fault for not reading thoroughly before I printed just the cut list and headed to the store. Still, I love it. I used the Square Planters with Finials plan for this. Painted it with a stencil in place, then stained over that. Also used a kreg jig.

I love the play loft bed, but wanted to add a princess twist for my 5 year old's birthday. I found melamine plywood, which helped in the finishing since it was already white. It was a lot of work, but so worth it! I think the kid's favorite feature so far is the slide, which has seen a ton of use :) My favorite feature is all the storage! Thanks so much Ana! If it wasn't for you, there is no way I would have had the courage to tackle a project like this!

I've always wanted a Cali King bed, but balked at the one to six thousand dollar price tag for the showroom models. This one is an excellent, straight-forward build with little modification needed from the plans given. The lumber yard staff was great at selecting high quality stock once they knew to what end what the pieces were going to be used, so utilize their expertise. Tolerances are fairly tight on this bed, so measure carefully, and more than once. With the addition of the four posts and canopy frame (also provided on www.Ana-White.com ), and a Stearns and Foster luxury plush mattress from Costco, I've more than got my money's worth. Indeed, so will my children. it's heirloom quality.

Saw this table and wanted to put it in my kitchen, looks great.

This is a project where we built the cabinets for our friends, and they added their own top to the desk.

These cabinets are each 18″ wide x 24″ deep x 26″ high, with the overall desk size being 72″ wide x 27″ deep x 27.5″ high.

These are constructed out of 3/4″ and 1/2″ plywood, with poplar face frames and shelf fronts.  The finish on the cabinets is a distressed white latex paint, finished with a few coats of clear Valspar Sealing Wax to give the cabinets a nice, soft feel.

You can see more pictures on our post on our site, or even get the plans if you want to build your own.

This chair was pretty easy to make with Ana's plans. I plan on making four more just like it (updated: completed). The only modification I made was adding another slat to the back of the chair. I used a miter saw for all cuts which really helped with the speed of the project. The 2x2's are treated pine and the 1x3 slats are cedar that I got from the "orange box store" for about four bucks a stick. I also primed and painted the 2x2's (legs) before I assembled. I could not imagine trying to paint the legs white and not getting at least some on that beautiful cedar. The contrast really pops in person. Thanks ana-white.com! $20 per chair.