Community Brag Posts

 I had heard about Ana on the YoungHouseLove podcast and she inspired me to take on this storage bin! It looks great and my 2 year old son loves it!  I documented the process on my blog at 1thing1week.com where I take on one new challenge each week. 

This was my first attempt at building and I learned a lot such as if you drop pine, it cracks in half - and - when cutting with a jigsaw, cut inside the lines....you can always trim more off, but you can't put it back - and - my dogs can distress a piece of furniture faster than I can if I put it under "thier" window....whether I want them to or not!
This was a great beginner project and gives a fast, satisfying result. As you can see, it has become the cat's bench...can't get a picture of it without him, he lives on it!
Just a couple of notes: I cut the legs more according to the plan diagram than the pretty cuts Patrick made on his...I wasn't ready for that. Also, I didn't have my glasses outside with me, so my measurements on the legs are probably not right. I made the top shorter because I wanted it for a specific space (which didn't work out, see note about about dogs and distressing....ugh!).
Also, this probably should have taken me just an hour or so, but I had my Kreg jig set all wrong and first had shallow pocket holes (see note above about pine breaking when dropped) and then made them too deep (learned to use wood filler)! That's when I finally got my butt into the house to get my glasses to read the dang directions (again!).
Thanks Patrick and Ana for giving me such a great, easy beginner project!

This project started on a Saturday and I moved it into the house the following Friday. All that being done with two little cherubs running around and making demands of me every 10 minutes. Super easy build and my first time.

King size, so I added two 1x3 supports on the back. I love it!

Building the desk was pretty straightforward. I actually saved a little money going with the 2x6s (4 of them was under half the price of a pine project panel) rather than the panel which I actually brought home first. I went with the 2x6s instead because it felt sturdier, and the straightest panel I could find was a little warped (which I didn't want to force).

My biggest piece of advice is, if you don't have a wood planer, DO NOT use a Kreg Jig to assemble the top first. 2xWhatevers just don't seem to "lay" the way you want them to if they're all connected together. I built the legs, added supports and then used glue and 2" finish nails to secure the top, butting them up as close as I could (there's only very minimal gaps, ~1/16 or less) It is SOLID. I filled in the nail holes with Elmer's stainable wood filler. After staining, I used a tiny artist brush with the stain on the filler so it could penetrate a little longer. Worked like a charm!

We decided to go with a color stain on top because it's going in a craft room/office so we wanted it to be bright and fun to get our creative juices flowing. The walls are a light gray so we figured we could afford some color :)

This project was meant to be a birthday present for my niece; however, after showing it to other people, there are now multiple people that are interested in having their own, understanding that I will be able to make it for much cheaper than buying an equivalent project from a store. It was a fun project and took little time to complete with minimal resources required....and for cheap

I had been searching for a loft bed for my son for some time but couldn’t find anything affordable until I stumbled across these great plans! I found the instructions to be very easy to follow (though I did spend a lot of time going over them first) and the cut diagrams were great to prevent waste. I also fell in love with hmkeith11 paint job which I copied as well. I used Behr paint in pencil sketch and just a large grout sponge to make the bricks. Super easy and turned out great.

I made a few modifications to the plans. First I made the towers 6ft tall but did not change the height of the mattress platform. I also made the towers one piece and just cut the tops of them to get the “castle look”. I made the towers taller so the rail on the front would be bigger and allow for a more “secure” feeling when sleeping (and to ease my fears of two fearless boys jumping on the bed). I also eliminated the small front piece that connects the slide to the tower. I just made the front door panel longer and attached the slide right to the tower with a few screws. I like the look better and it eliminates a small rail at the top of this small panel giving it clean look (in my opinion). I also added a small door under the stairs since the wall was long enough in my son’s room. Its fun and adds a second exit point. Lastly, I modified the supports for the mattress based on some other brag posts feedback. I rested the support beams on the plywood sides and added a third beam and 2 beams going across tied into the wall studs and the front door panel. I wanted to feel 100% sure my very active kids couldn’t bring this bed down. I also added a piece of plywood on top of the bed supports since we have memory foam mattress, this gave the mattress the correct support it needs.

This was by far the biggest woodworking project I have ever taken on. It took me 2 months of working just weekends for only a few hours a day and some evenings after my kids went to sleep. Perfect size project for me. I’m also a short female, so go for it moms! You can do it!

I had also never cut such large pieces of plywood and didn’t know how to get my cuts straight. I found out how to make a skill saw guide and boom! Problem solved. Just buy a piece of Masonite, rip a 4 inch piece then glue it down on the other piece with the manufacture straight edge pointing in and you got yourself a guide for straight cuts! Here is a link: http://www.provenwoodworking.com/woodworking-saw.html

My son is thrilled with his bed and it was a great challenge to build!

Rustic Industrial Shelf

The Swede in Norway

I built this for a friends upcoming baby shower! She has yet to receive it so I hope she loves it. It was super easy to build, even the fancy scrolling at the bottom of the sides was relatively easy. I can say that only because I'm an experienced builder, but for someone new to this, it could be daunting. Just go slow and try it out on practice boards first!

So easy and fun!

Eaasy to build. Just measure the wood. I used My finish nailer and pocket hole screws and counter sunk wood screws. I used 1/8 piece  masonite instead of the plywood. My wife also knited blankets and  my mother made the mattress and pillows. They just loved them.

Love making it!!!

We modified the farmhouse table plan and made office desks from reclaimed lumber! Check out the full post on my blog: http://livingvintageco.com/category/do-it-yourself/woodworking/.

My husband and I took two plans, the Mantel Moulding Headboard, and the Chestwick Platform Bed. We made some slight modifications which are as follows.

For the Mantel Moulding Headboard I wanted it to be a tall. The original plans called for the headboard to be 61 1/2 inches. We made ours so that it sat at 74 inches. We also made the width of the headboard 60 inches so that it was a perfect fit for the base.

For the Chestwick Platform bed we used 2X12's. Since we decided to make the headboard taller, I felt that the 2X8s wouldn't have been aesthetically pleasing. We used heavy duty top corner plates to screw in the bun feet.

Mounting the headboard: Due to the size of this headboard, it is recommended that you attach to a stud in the wall behind headboard to prevent forward tipping. We used french fleat picture hanger with wall dog mounting screws (200 lbs), read instructions. We attached two vertical 1X2's to the back of the headboard for added support, since the headboard rests on the platform bed. After the headboard was properly secured to the wall, and resting on the platform bed, we then installed four mounting brackets. 2 heavy duty corner brackets, and 2 mounting brackets. The heavy duty corner brackets are long enough to screw into the mattress supports, the platform bed, and the headboard (see pics).

This was our second project, and we couldn't have done it without Ana's help.

Was realy easy to build.

DIY Entry Table