Fancy X Farmhouse table with 4x4 base
![](/sites/default/files/20141231_145327.jpg)
I used 4x4 post for the base.
![](/sites/default/files/20141231_145313_0.jpg)
![](/sites/default/files/20150611_210022_0.jpg)
![](/sites/default/files/20150611_210042.jpg)
I used 4x4 post for the base.
I wanted some Cornhole Boards and I wanted to make them myself. I used some vinyl stickers (distressed American flags) that I got on Amazon! I also bought the Cornhole Bag set on Amazon as well! I added some carrying handles from hardware At Home Depot. I found the link here on Ana's website! I love them!
Was a fun build. Took 3 days. Ana your awesome.
My take on the Rustic X Console.
Fun project, ordered the hardware for the rail system itself and the wheels were too big so I made my own rail system.
Mon, 02/07/2022 - 10:10
Beautiful build. Looking forward to building one of my own.
So my sister moved back to Southern California from New York. She found a great place but needed a table. I made one table and one bench. My sister then found two chairs for the other side. This is the second or third thing I have made/built from Ana’s site. Thank you for making me feel more manly with great instruction. I also built this pre Covid-19 when lumber was not so expensive.
Tue, 10/05/2021 - 09:55
Great housewarming gift, and very pretty too! Thanks for sharing!
Modifications to Ana's original plan:
My husband, step father and I built these Thanksgiving weekend (2010) and my mom got us a half bushel of oysters to snack on and made awesome steamed mussels with bread for dinner. This was a very fun family weekend.
I modifyed the plans a little to make the arms angle in a bit instead of being straight boards and also created the curved front. Then after building the first chair, Pat decided to make the second chair's back rest taller and cut angles to match the arms.
I picked intermediate because of needing a miter saw for all the different angles needed for getting the front right.
Also, It took one day for each chair
We altered the original plan by enlarging the sandbox (approx 5' x 6') which made for wider benches that can comfortably seat an adult. The benches and back rests are three boards deep instead of two. We added 2x12 supports under the benches for additional support, as well as another 2x4 support in the middle of the backrest.
Tue, 04/14/2015 - 20:00
I just love seeing pictures of these built! Makes my heart swell :-)
Used pressure treated (copper) and will allow to fade to grey with sun and sea air. Built to enjoy PEI mussels, lobster and beer in the open air and not too worried about the finish or surface. The table took 3 hours, start to finish - benches x 2 took longer at about 7 hours. Am getting a little lateral movement with the benches so will replace the 1 x 3 spacer with 2 x 4 and may add a diagonal 2 x 2 support as well (to match the table). I don't have/didn't use a Kreg so that may be the issue...?
Plans on Ana White are fantastic - I made the see-saw this weekend too in about an hour....thanks!
I used the "how to build" from the Shepherd Kitchen Island plan to help me create my own dimensions for this bar... 60" long, 24" deep, 35" high. It has a space on the left for an under counter ice maker and the wine rack is built in inside the right hand cabinet.
The counter top is plywood covered with a sheet of zinc I bought from rotometals. Fairly easy to do after watching their videos on how to apply and how to patina.
This was my first Ana White project, and I learned a lot from making it since I was also a novice woodworker. I am very happy with the end result, but it was probably a good thing that this went on the inside of a closet :) It gave me the confidence to go on and build something more difficult with the skills I built along with the storage.
The $30 estimate is only for the wood. Wood putty, sandpaper, screws, paint, etc. will make this more expensive, but you will use all of the extras on other projects since this one won't use those up.
The time involved is a guess--it has been a few months since I completed this. Someone with experience could probably do it faster and someone brand new to building might go slower. So I chose 3-6 hours, a nice in-between number.
Watch your caster size with carpet. That was my only snag with the instructions. Ana has hardwood floors that the casters roll on. I have carpet so I wanted larger wheels in order for smoother rolling. That added height to the caster also, so you want to modify the length of the sides of the storage unit to reflect the larger casters on carpet.
All in all a great plan and useful end result!
**UPDATE--January 30, 2012** We removed the casters from the bottom of this just yesterday and the door opens SO much easier. I would invest in some high quality casters and not the cheap ones I bought if you are going to use these. Without the casters I am only putting light things (stuffed animals) in this. If you are using it for heavier items, I would use the casters but make sure they readily turn. The casters I had did not want to turn as the door moved and they dragged on the carpet instead. Also, the overall height of your unit will depend on the height of your casters, so buy them first if you are going to use them. I still love this though!
Farmhouse dining room table built for my mom. Unstained.
Table top is 2" White Pine Boards, legs are cedar, and everything else is whitewood studs. Left the leg assemblies and stretcher board unattached for the two hour transport to Charlotte. Attached them with screws and some glue upon arrival. Loved the plan and finished in two days!
I was inspired by your coffee station plans to build this unit. I added an upper shelf with gas pipping, along with LED lights under the shelf. This station has been very popular in our house.
I absolutely love the way these turned out! I drew up an example in Sketch-up using Ana's plans for the Simple Nightstand as a starting point.
How to build a Bottle Cap Tray AND what NOT to do.
These Bottle Cap Trays are sold for 45+ Bucks online. I spend maybe 15$ on it.
You need a lot of Friends drinking a lot of different Beers... For this tray i needed 88 Caps. I also asked Bartenders and Co-Workers to collect Caps. As more colorfull you get as better. Twist off Caps are the best behause they do not have dents.
I bought the Tray at Hobby Lobby for 3.99$ (you can also build one from a Plan from this Side) and after sanding with 220Grid i stained it to fit my Home Bar. After lay out the "Design" i removed them all and lay them in the back of the now empty tray.
2 Ways to glue the Caps to the Board:
1. Hot Glue (be carefull the Caps get very Hot)
2. I poured just a small amount of the Epoxy in there and pushed the Caps into the Ressin...
How to mix Ressin...
Read the Manuall!!! The first 2 Trays i poured to much and then it gets very very hot and ruin everything (see second last Picture). 2nd Glue the board to the Walls, if the Ressin runs out of the Tablet it is also a great mess!
I Used 2 small cups messured it and Mixed it in the Red Solo Cup...
Put the Tablet on an even surface (protect it) and pour a small amount into the tray... Level it and then put the Caps in there and use a torch to get rid of the Air Bubbles. I needed 3 layers to Cover all Caps. Keep it Dustfree during curing - very important .
I let it cure for 12 Hours bevor the next layer was applied. Total Curie after 72 Hours...
Sorry for Bad English - i am German...
Hope that helps to build your own Bottle Cap Tray...
And made it as colorfull as possible. I aranged them to face One Side but you also can turn them happy around.
Thanks for comments and Reading
Jann
I built this for my four year old son! He even helped me out so that made him love it even more :)
Thanks for the joy of this project! Our family of 5 just got a new kitchen table, and everyone pitched in to build it.
The ongoing saga of our cruddy old kitchen is finally over, for the most part. We attempted the quick fix and failed and now with a little time, knowledge and cash we think we finally got it right. Our ceilings are lower than the average house so we couldn't buy stock cabinets. We custom made everything and added some accessories. All thanks to Ana-White!! You are so awesome!!
For more photos etc... just visit:
http://buckleyjournal.blogspot.com/2013/07/kitchen-reno-redo-20.html
Tue, 07/16/2013 - 13:45
Amazing job, MCBuckle! Off to click over to read more about it
Thu, 07/18/2013 - 23:16
You've got guts AND glory! :) Wish I had the confidence a year ago to build our kitchen cabinets. I hired a friend of a friend. It took months for him to build the 5 bases, then he took another job and left our kitchen without doors and drawers. If he doesn't come this weekend like he promised, I'm revving up our circular saw and growing some guts myself.
Thank you for the inspiration. (Oh, I was not able to post a comment on your blog. When it asked me to type in the code to prove I am not a robot or web spider, the submit comment button was missing.)
Fri, 07/19/2013 - 05:48
Go for it!! Trust me, if I could do it anybody can.
And thanks for the heads up, I think I fixed the comment issue!
These are made from the three drawer plans but modified the size to meet our needs and used planks for shelves instead of drawers. Painted white and black gel stain.
UPDATE FROM ANA - We have received MANY requests for this plan and have created a plan inspired by this post here.
Shopping List (for ONE bedside table) + Tools
Cut List (for ONE bedside table)
Cut 1x4s and 1x2s with miter saw. Layout side panel 1x4s as shown above. Measure and cut 1x2 to length. Nail the 1x2 to the 1x4s, two nails per overlap with glue. Make sure your side panels are square. Build two.
Drill 3/4" pocket holes on inside edge of 1x4 ends as shown above. Cut 2x2s with compound miter saw. Attach to the 2x2 legs with 1-1/4" pocket hole screws.
Set Kreg Jig to 1-1/2" setting. Drill 1-1/2" pocket holes on end of each 2x2, one per end. Attach to 2x2s with wood glue as shown above.
Cut 1x4 shelf boards with compound miter saw. Nail and glue to the inside of the project as shown above.
Cut 1x4 top boards with compound miter saw. Nail and glue to top with 1-1/4" nails and wood glue.
If you wish to add a back, measure and cut from 1/4" plywood and attach with 3/4" brad nails.
Mon, 02/12/2018 - 16:24
Is there plans for this one? Its gorgeous and I'd love to build it!
In reply to Is there plans for this one? by laurahamer07
Thu, 06/07/2018 - 15:37
Hello, this nightstand was built using these plans http://www.ana-white.com/2011/06/reclaimed-wood-look-bedside-table instead of adding drawers the builder added shelves. The shelves can be 3/4" plywood or 1x boards.
In reply to bedside end tables by karenlouder
Thu, 06/07/2018 - 15:40
Hello, this nightstand was built using this plan, but instead of drawers, simply measure and cut shelves to fit from 3/4" plywood. http://www.ana-white.com/2011/06/reclaimed-wood-look-bedside-table
Wed, 07/24/2019 - 09:24
It's taken us a couple of weekends, but we finished our bedside table. We made two, but one still needs painting.
Thank you for the plans. We had a great deal of fun and learning experience making these.
Want to see it? https://www.facebook.com/photo.php?fbid=2830583376957272&set=pcb.283058…
I built some French Tuteur’s for the garden.
Fresh and ready for my new raised beds.
Comments
Ana White
Fri, 03/06/2015 - 15:54
This is really pretty! I love
This is really pretty! I love the way that you staged it too!
aggielandma12
Sat, 03/07/2015 - 10:01
Thanks.
We are waiting on our slip cover chairs (on back order). I have built a matching bench that needs to be finished.
Leslie Is Ready
Sat, 03/07/2015 - 16:44
This is Beautiful
Stunning job! You have definitely inspired me!
aggielandma12
Thu, 06/11/2015 - 19:42
added chairs and matching bench
Finally
dadmandude
Tue, 05/10/2016 - 10:20
4x4 Measurements?
I'd also like to build this table using 4x4's. Can you tell me how you came up with the lengths for the diagonal pieces? Also, how did you attach the perpendicular end pieces to the top? I've been looking to do that as well and on all the plans I've seen they used pocket holes and I know that will not last before the end pieces begin to sag.
Thank you!
brian.heere
Mon, 08/19/2019 - 07:45
Did you ever find the…
Did you ever find the measurements and details? I'm interested in making the same table!