Community Brag Posts

Built this a little smaller - only 15" deep and 42" wide for use behind the couch with multiple functions - laptop desk, dining room buffet table, and behind-the-couch-set-things-on table. Love it!

Tricky parts - the drawers. Because I changed the dimensions, I built the drawer box to fit my new dimensions and installed it. Then, I cut the sides of my drawers 10" deep (the smallest drawer slides I could find and a perfect fit). I laid the Hettich ball bearing drawer slides (from my local lumber and cabinet supplier, not big box) in the drawer box and trimmed down my drawer front/back until they fit nicely. If you're interested, it was 15 1/8" wide.

Nail gun is a must on this project!!! And remember to glue and use 2" nails.

I used the Kreg jig to build my drawers because I'm familiar with building drawers that way and feel comfortable getting them squared. I highly recommend the Kreg jig!

Then, I attacked it with my orbital sander until it was nice and smooth.

Love Ana's great patterns!

This was so fun. My little girl loves it and we have another on the way, so I am thrilled with how it turned out. The assembly wasn't hard, but it took FOUR coats of paint and three coats of finish. That was the most tedious part. I made a box for the apron sink, rounded off the edges, sprayed it with a white lacquer, and modified the countertop so it fit in nice and snug. It's my favorite part. I love that it tied in the white fridge. It ended up costing me 130 bucks. 50 in wood, 35 in paint/supplies, 45 in handles, knobs, faucet, hinges, stovetop etc.

COUNTERTOP AND SINK MODIFICATION:
I hope this isn't too confusing. It's hard when you can't see it, so don't hesitate to email for clarifications.

Countertop
(2) 1x3 @ 10 ½” (these boards go on either side of the sink when looking from above)

(1) 1x4 @ 11“ (this is the board the faucet sits on)

Put the backsplash on the same way the original plans say.

Sink box
11” wide, 8” deep, 5.5“ high (Using all 1x6 boards)

(2) 1x6 @ 11” (front and back)

(2) 1x6 @ 6.5” (left and right sides, on the inside of the 11" boards)

6.5x9.5 inside bottom (cut down whatever board you need to to get this size. This should fit snuggly inside the walls of the box)

Because a 1x6 is really 5.5 inches wide, and the countertop is 3/4" thick, and 3/4" of the sink sits above the countertop, that means 4” of the sink will be under the countertop. So looking at the sink from the front, you need (2) 1 ¾” wide x 4” long blocks of wood on either side of the front part of the sink. Then I just put a 1x12x14 1/2" shelf under the whole thing to hold it up. I built the sink box first and spray-painted it with a white lacquer, then I built the entire sink countertop and base, and then shoved the sink in last. It was a very tight squeeze so I didn't have to nail or glue it in or anything. About an inch of the sink should be sticking out of the front, and 3/4" should be sticking out the top.

Good luck!
Email me for questions!
[email protected]

Or visit my blog for details where I got all the accessories
carlyandjordan.blogspot.com/2013/08/play-kitchen.html

Love how it turned out cost a little more if you count stain,wood conditioner..etc wasn't bad still.wood probably cost around 60-70 cheap and better then most anything you can buy.. Lots more to come 

I used the Rustic Coffee Table Plans from ana-white.com, but purchased lift top hinges and added 2" x 6" around the perimeter, which provided storage inside when the top is lifted.

We built this corner cabinet shelf in three days (only because it is over 100 degrees here, so we had to wait until 9:00 at night to work on it) for our office space. We love, love, love it and can't believe how nice my corner cabinet turned out. Only our second building project ever. :)

We needed a desk for my kid's computer. Something simple and functional but with a little customization.

Since we live in Hawaii ocean themes are everywhere in our home. I scrolled out the waves to make the shelf supports original and let light into the little cubby below.

24" across and 18" deep I built this off the rough plans for the Clara desk and customized it to be at a normal table height of 29" so my elementary school children will be able to use this all the way through high school.

Stained with a blue minwax wood stain on the legs and shelf support. Arctic white latex paint for the table and shelf tops.

My under the sink door cabinet is smaller than what's on the plan so i had to improvise.  A paper towel dispenser won't fit anymore so I just made another shelf.  I love it.  No clutter and everything is so organized. :) 

Our kitchen table buggered out so I decided to give making one a try. This was my first project. With seriously low funds available- I asked around to family for scrap lumber. Turns out the old lumber in the barn was black walnut! I had to plane and join it by hand so it took quite a bit longer to make.
I made the table one foot shorter and one foot wider. It seats 6 comfortably on the sides. Thank you so much for the plans!

This was my first major DIY build and I LOVED the way it turned out! I have wanted a large office desk for quite awhile, but never could find anything in a store that fit my needs and/or style. I modified the plans to fit what I wanted and it turned out great! The top is just a hollow-core door from Lowes ($19) that I stained with a Dark Walnut color. I added a file drawer to the right and just a hinged pull-down door on the left for more hidden storage. Purchased the baskets at Michael's for 50% off.

After I built the dresser for my son, he decided he needed a nightstand. This was his project, I only advised and offered assistance. He was 15 and he came up with the design and we glued up the panels. He cut, sanded and assembled himself. He stained and applied the shellac. I am very proud of him.

Great project!

I wanted to make something using the plethora of scraps in my garage. I ended up making this shelf that calls for 1x6 pieces with 1x8's and I didn't even have enough for that so I cut down some 1x12 pieces and used those too. The long part of the shelf is actually two pieces screwed together using pocket holes. Check out my blog for more on this project!

It took me a long time to finish the chairs, although the table was a snap. The time consuming thing was my desire for two paint colors. Painting is not my strong suit. But I got it done, just in time for our annual Labor Day house party.
I cut the lumber using our radial arm saw. I sanded with an random orbital sander, and used really great cordless drill and driver. My husband likes to buy good tools, but hardly ever uses them.
I had never used pocket screws before: I love them and found it very necessary to use the face clamp and right angle clamp Kreg sells to prevent splitting. My assortment of speedclamps were not getting the job done.
For the table, I tried masking off the white when I painted the red on the legs, which did not go so well as there was annoying paint-creep under the tape. I also decided that the red paint needed two coats to look good (it actually seemed to do better on bare wood then on primed wood.) So that took more time.
I finally bought a really good paint brush and that made a huge and positive difference.
I had intended to paint the chairs' slats red, but the back frame white, and the side supports red. To do this I intended to paint individual pieces and assemble the painted pieces, but the splitting (before I invested in the specialized clamps) was heartbreaking after all the sanding and painting. So I took a month off from the project, ordered clamps, recut a few pieces, and simplified my paint scheme. Much better!
I'm looking forward to starting my next project (NO paint!)

I started about 2 years ago by making one of the Mini Farmhouse Style bedside tables.  My wife loved it so I made a second.  Then I made the bench a year or so ago with plans from this site too.  Unfortunately I can't find where those plans are now.  Maybe in Ana's book (I have that at home too)? I just finished the Reclaimed Wood Headboard with wood I reclaimed from the big orange store :)
I put a 1/4" chamfer on the edges of the panels for the headboard, and had to add a brace in the back because none of them were perfectly flat.  No one has seen the headboard yet, but I've had friends ask me where I bought the bedside tables and bench.  I've never had a matched set before.  This is a definite bedroom upgrade!
Stain is Minwax Special Walnut, paint is Gotham Grey from Behr.

Modified to Full sized, my first bed!

Really simple and quick plan, great for a first timer. I oughta know. This was the first piece of wooden furniture I've ever built. Thank you so much Ana!

I made a version of this crate for the top of my family's refrigerator. I didn't have enough scrap 1x3s, so I used 1x2s as well. Instead of using chalkboard paint, I stained the 1/4" front and painted "nourish" with white paint. I also used old drawer pulls I saved instead of cutting out handles.