Community Brag Posts

My husband & I built this version of the Husky Farmhouse Table. We also built two benches & bought chairs to match the colors as closely as we could. We. LOVE. It! I found the legs on Etsy for a little cheaper than the place Ana reccomends in the plans. The milk paint didn't crackle as much as I wanted, but I think that was because I put the first coat on WAY too thin since I was afraid of running out. And I ended up doing 3 coats. We were able to sand the edges & some spots down a bit to get the effect we wanted though. Super excited to have Christmas dinner at this baby!

So this was my first project. It's not perfect, but I LOVED how it turned out!! A few lessons learned....
1) I know common sense would tell you to get the straightest boards, which I thought I did. When I went to put them together, a few were bowed. I tried to put those at the bottom.
2) I did end up putting a brace vertically in the middle on the back with left over 1x6. It just added a little more support.
3) Since I'm a beginner, I didn't know better, but go easy on the wood filler, especially if you are going to use any kind of opaque finish.
4) The only other thing I can think of, is unless you have someone to help you out, build this close to where you plan on putting it. I am in the middle of a remodel, so was able to build this in my bedroom. This sucker is heavy and awkward for one person to move when it's finished!!!
5) I built this with my finish nailer (2" nails) and wood glue. (Light on the glue...it expands quite a bit!)

My first pocket hole project! Adjusted plans to make table 50 inches long.

Baby changing table for a baby shower gift.

I built this Auburn University themed platform bed for our son. It works perfectly for him, and he absolutely loves it. I added a custom "Tiger Eyes" wood logo, which makes this a one-of-a-kind bed.

The construction of the bed was straight-forward due to the great plans I found on this site. The finishing process actually took longer than the build!

I made a few minor tweaks to the plan, such as using a combination of dowels and wood screws on the frame joints, and using a router to put a 1/2" radius round-over edge on the platform boards, and a 5/32" Roman Ogee edge on the top plate of the headboard.

We used spray paint for the finishing process (Rust-Oleum Gloss Orange and Krylon Gloss Navy), followed with a few coats of Minwax Fast-Drying Polyurethane.

If you want to read more about the build process, you can check out our blog posting at: http://ourhomeourhands.com/auburn-university-platform-bed-ana-white-ins…

As part of a redecorating project using reclaimed barn wood for our guest bedroom, we constructed this window frame to display some photos from one of our siblings of barns found in Iowa.

The dimensions are 44” X 33” with each photographic image being 11” x 16.5”.
Since the wood had so many bore holes, we used ¾” redwood under the visible fascia for added strength.

Cost - $75 / 4.5 hours to build.

http://ana-white.com/2009/12/plans-barnwood-frames-1-and-10-minutes.html

I needed a shed to get my outdoor and seldomly used equipment out of my gargage.  But I needed the shed to be small so it doesn't take up too much space in the back yard and my HOA will not allow it to be taller than my fence.  So I needed a small/short shed.  I didn't use any plans, but it would probably have been quicker if I had.  I did it with free time during a week, but could probably be all completed during a weekend.  It was probably a few hundred total.  I tried to reuse existing hardware/wood where possible.  I'm a cheapskape.  Here's my blogpost I did with additional pictures...

https://drowland.wordpress.com/2017/12/22/small-short-storage-shed/

You can see I also added a matching doghouse. 

I used the farm house plans for this bed but I made my 4x4 taller because I wanted the post affect, I also added the" \/ " because I wanted a "rustic look. I used 2 different stains to get the old barn wood look. I had a great time making this bed and LOVE it Thanks for the ideas.

This week's project was an outfeed/assembly table. A project that iv'e been needing for a while now. It's mostly constructed with 2x4's and plywood and mdf for the tops. I added caster the the legs to keep it mobile in my shop in case of having to move it around. I'm extremely happy with it and I love the extra space it provides underneath.

Blog article: http://www.lanebroswoodshop.com/2015/05/assemblyoutfeed-table.html

Video: https://www.youtube.com/watch?v=Hap5Dv60qHw

Built this for our daughter for Christmas!  She loves it! Very easy build

This table is enormous at 106" long made from pine boards and fir studs. A very easy build considering the final outcome, totally doable by any DIYer.

Instead of having the plywood top sit on top of the frame, I sunk it into the frame instead with 2x4 supports underneath.