Community Brag Posts

We built this entryway locker using Hillarys plans. It turned out amazing and it gets more use than any piece of furniture in our house at the moment.

I needed a place for my kids to put their shoes so I shrunk the plan for the X Console and made it fit my entry way. I love it!

This was my very first project. People ask me how much it cost me to make it, and I don't know that you can quantify the satisfaction of making our own furniture. The whole family helped in making this table. We elected for the Rust-o-leum Kona stain and then a semi-gloss poly. i think my next project will be a kitchen table, some built-ins as well as taking my son's favorite college team logo to embed onto a chair. Thank you for making the available and easy to follow.

I worked on this in the evenings after work so it took more than a day or two to complete. Plus sanding, staining and finishing if done right took over the course of a couple of nights.

I finally finished the bedroom set, this one the last piece (and the biggest dresser).

More info on this 1970's bedroom set here:

http://www.woodworkingfourdummies.com/blog/dresser-set-makeover

Cheers,
Ian

Slightly more elegant version of an outdoor cedar patio table. This is made from 100% cedar and joined using Kreg pocket hole screws. The finish is 2 coats of Sikkens Cetol MRD that has been hand rubbed on using a cloth, with 24 hours of dry time between coats.

I've loved this little tree shelf since it was first published, but thought the angle cuts might be too difficult.  I was wrong.  It was simple and fun, with an extra pair of hands. Made a few minor changes. Merry Christmas & thanks for the cute plan!

I built this using the Kentwood bookshelf plans as a guide. I made my shelves 3 ft wide and made it aprox. 8 ft tall. I also bought the KREG shelf pin jig and built the shelves to be adjustable. I haven't chosen a finish yet because I am waiting for my son to pick a color since it is going in his room. I am considering fixing a shelf in place and building some doors for the bottom. I worked on this over a week span, however I could only do bits and pieces at a time. The sanding took longer than the build because I plugged the pocket holes and they take longer to sand down.

This bed is so perfect for my studio apartment. I don't have the floor space for multiple dressers, and the modular 3 bench design made it super easy to move in (and hopefully to move back out when school is over). LOVE LOVE LOVE this project.

I also made the headboard.
It is a single sheet of plywood, cut down and covered with polyfill and fabric. We predirlled holes for the buttons, and I set the headboard (fabric side up) across 2 saw horses with a flashlight underneath so I could see the drilled holes. I used nylon thread and a large needle to attach the buttons. There are flat buttons on the backsides of the holes so the thread doesn't slide through. It is hung directly on the wall behind the bed via wire hooks - make sure you hang it from the studs!

Needed a place to store wood for the fireplace and firepit. This very nicely organizes what was before a huge dirty pile of wood scattered on the ground. Cedar pickets for the top, all is coated in exterior white stain. Holding up nicely so far.

Love the desk! A few issues I had though are that the top panel will not go into the space of the top angle pieces are in place. I had to remove them to get it in. Additionally, the pocket holes seemed insufficient for the top 2x2s because of the angle they are at, so I went back and drilled countersink holes directly into the adjacent support board and added wool glue. Lastly, for then 2x2s that are supporting the bottom panel, I was worried about just having the pocket holes there as well because I could see my 5 year old climbing on it to reach the pegboard so I added L brackets to the bottom of the 2x2s under the bottom panel. I also added a light to the underside of the top panel and supports at the bottom near the floor. Turned out great 

I followed Anna's plans pretty closely though deviated somewhat as well. Added additional length and one more seat separators & seat, increased depth by a few inches, changed design of seperators to allow for arm rests, added some additional trim, a second inset shelf w/in the shoe box area (for sandals and whatnot), and then inset wainscoting.