Community Brag Posts

I started this project with the intention of building the octagon table.  The person I was building it for changed their mind and asked for round instead.  With the table top now being round I did not think that the supports underneath the table fit with the design so I used the leftover scraps from cutting the round top to make the altered supports you see in my photos.  Turned out pretty good I think and the recipient is in love with the design.  Thanks for the original plans Ana and good luck to everyone else building this table!

I made this for my 5 year old daughter for Christmas.  I really like how beautiful and sturdy this play kitchen is.  I added 4 inches to the height so it would be the right size for my daughter.  I also made all the sections equal in width.  This made it simpler for cutting the shelves.  The faucet is made from various pvc pipes and spray painted with Rustoleum silver.  All the knobs are able to be turned, and the faucet can swivel.  For the oven shelf, I used a cooling rack.  Thank you so much for this wonderful plan!

This is the Ipex bookcase (plans on this site). My husband built it for our almost 11 year old's room. He modified it to be 36 inches wide rather than 48. Painting scheme done by me - she is into black and white/zebra.
We are pleased!!

I used Ana's plans and Hillary's suggestions to build this extra large buffet.  It took probably 25-30 hours if you consider the extra trips to Home Depot and Lowe's because I didn't yet have the proper tools.  I used Annie Sloan's French Linen as my base coat, Old White as my dry brush coat, Annie Sloan Clear Wax throughout and Dark Wax in the crevices.  This was my first big league build, so I had to recruit a skilled neighbor for assistance with the drawers and doors.  My two recommendations would be to ensure the piece is square at every step, and to cut the wood as you go.  Don't make all the cuts at once because there will be adjustments.

I used Ana’s plans to make my queen sized headboard. I used 1x8’s for the verticals and changed the framing a bit to only have one piece of wood on top. I also left out the 2 extra board on the back to save some cost. I glued and nail gunned each vertical piece to the top and bottom 1x4. I attached the assembled center to the 2 posts with pocket screws and small L corner brackets for stability. I also adjusted the height of my project to come to approximately 64 inches tall and the bottom of the inner picture portion, where the mattress reaches the headboard, to just hit the top of that 1x4 so we never have missing objects that have fallen behind the bed. I did use the green pressure treated lumber for the 4x4’s and they stained just fine. I also added a farmhouse style X through the center. I ripped my top 2x6 on both sides to be approximately 5 inches wide, so the rounded edge of the worn lumber is now square. I stained this in minwax dark walnut then went over with a second color coat of minwax classic grey. My apartment isn’t big enough for the sides and foot board but someday if we move, I’ll be able to complete the entire bed set.

Norwegian version.

Wood sizes in millimeters:
Can be bought from Byggmax, Monter or Coop Obs bygg for example.
36x48mm
48x98mm
48x148mm

Lessons learned: Dont buy cheap tools and make sure the wood is straight.

My husband built this bed for our 4 year old son and let me say its just perfect! His room is on the smaller side and this made a huge difference for him to have more play room. When my son seen it his eyes filled up with tears he was so excited! My husband built this bed on a Sunday afternoon. He torched the wood along the grain, and then over a period of a week added clear (he used 3 coats as the wood just soaked it up pretty good ). Highly reccomend this project!

I built my new sofa!
I am so happy how it turned out. I had to translate all the instuctions in french, and modify the dimensions to adapt them to the lumbers I found in my country (France)
I had to change inches in centimeters too.
It was just a little difficult but I built it!!!
Thank you so much Ana, I am one of your fan.

First time I designed a piece of furniture.  Made out of pine.  Slat top and bottom with book shelves on both ends.  Joints held with glue and pocket screws.  Minwax pre-stain conditioner.  Two coats of Minwax Provincial stain.  Three coats of polyurethane.  

I used the plans from the website and added a few extra features that we really wanted .we made the tracks for the sliding doors ourselves and got all the hardware for really cheap. Also, added leds on upper/lower shelving to give to a really cool look at night. All in all, we didn't spend more than $350-$400 on this awesome piece. 

My hubby and I built this for a fundraiser. A few challenges along the way, but lessons learned for future projects!

Built this for a customer of mine. Love this bed, it's our current personal frame also. Paint is behr ultra white. Ty @ana for the plans

Built the console (without the hutch) and my wife wanted another one a little diffrent for the other wall so I modified the plans a bit and made the second one. this was our first "distressed" paint job. I think it turned out great!

My husband built this as my Christmas gift. It couldn’t have turned out any better. We shortened it to 75 inches and added a butcher block top to match the floating shelves and island in my kitchen. The plans were very easy to follow. We did have to spend quite a bit of time planning out the barn door track, but it was worth it.

I loved that I used strapping, or furring strips, for this bead. The topper wood is a 2X4, but every other 8" piece of wood cost between $1.25 and $1.99 each. Yeah! Of course, for that price, you have to know you will be sanding the heck out of it. We had a metal frame for this bed but I wanted a headboard. Because it was going against a wall with a 45 degree angle, I had to make it a lot shorter than I wanted. I made it just tall enough so both pillows, when stacked on top of each other, did not fall off the back. I just love it.

Although I know the original idea for this plan was to save space, I ended up building a bigger version. I loved the design and overall look but wanted something with more counter space. My husband does property maintenance, and is always coming home with scraps of wood he salvaged from work. I dug through his wood pile for 90% of the wood I used on this project. I repurposed most of the accessories and bought the rest (including the hardware) from the dollar store. I spent a total of $38 on the entire project! I absolutely love how it turned out and can't wait to see the look on my daughters face on her birthday!